Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Variable Value
ftp Activates or disables FTP for the specified policy.
Because FTP derives its login and password from
the ACLI management filters, FTP works for read-
write-all (rwa) and read-write (rw) access, but not for
the read-only (ro) access. Use the no operator to
remove this configuration.
host WORD<0–46> For remote login access, specifies the trusted host
address as an IP address.
The switch supports access-policies over IPv4 and
IPv6 with no difference to functionality or
configuration.
Use the no operator to remove this configuration.
http Activates the HTTP for this access policy. Use the no
operator to remove this configuration.
mode <allow|deny> Specifies whether the designated network address is
allowed access to the system through the specified
access service. The default is allow.
If you configure the access policy mode to deny, the
system checks the mode and service, and if they
match the system denies the connection. With the
access policy mode configured to deny, the system
does not check accesslevel and access-
strict information. If you configure the access
policy mode to allow, the system continues to check
the accesslevel and access-strict
information.
network <A.B.C.D> <A.B.C.D> Specifies the IP address and subnet mask for IPv4
or the IP address and prefix for IPv6 that can access
the system through the specified access service.
The switch supports access-policies over IPv4 and
IPv6 with no difference to functionality or
configuration.
Use the no operator to remove this configuration.
precedence <1-128> Specifies a precedence value for a policy, expressed
as a number from 1–128. The precedence value
determines which policy the system uses if multiple
policies apply. Lower numbers take higher
precedence. The default value is 10.
snmp-group WORD<1–32> <snmpv1|snmpv2c|usm> Adds an SNMP version 3 group under the access
policy.
WORD<1–32> is the SNMP version 3 group name
consisting of 1–32 characters.
Table continues…
System access configuration using ACLI
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 177
Comments on this document? infodev@avaya.com