Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Variable Value
validity-period-in-days <30-3650> Specifies an expiration time for the certificate. The
default is 365 days.
Disabling SFTP without disabling SSH
Disable SFTP while allowing SSH to remain active.
Before you begin
Enhanced secure mode must be enabled. For information about enabling enhanced secure mode,
see
Enabling enhanced secure mode on page 181.
Procedure
1. Enter Global Configuration mode:
enable
configure terminal
2. Enable the SSHv2 server:
enable ssh sftp
3. Save the configuration file:
save config
Secure Shell configuration using Enterprise Device
Manager
Use Secure Shell version 2 (SSHv2) to enable secure communications support over a network for
authentication, encryption, and network Integrity.
On IPv6 networks, the VSP switch supports SSHv2 server only. The VSP switch does not support
outbound SSHv2 client over IPv6. The VSP switch supports both SSHv2 server and SSHv2 client.
For more information, see Changing Secure Shell configuration parameters on page 160.
For information about downloading and enabling security encryption, see Downloading the
software on page 151.
Downloading the software
Download new software to upgrade the VSP switch. Software downloads can include encryption
modules and software images.
Secure Shell configuration using Enterprise Device Manager
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 159
Comments on this document? infodev@avaya.com