Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Feature license files
After you obtain the license file to enable Premier License features, you must install the license file
on the system to unlock the associated licensed features. You must load a license file on the
internal flash of the device.
License installation using ACLI
Install and manage a license file for the switch by using the Avaya command line interface (ACLI).
Installing a license file
Before you begin
• You must enable the File Transfer Protocol (FTP) or Trivial File Transfer Protocol (TFTP)
server depending on which protocol you use to download the license file to the device.
• Ensure that you have the correct license file with the base MAC address of the switch on which
you need to install the license. Otherwise, the system does not unblock the licensed features.
About this task
Install a license file on the switch to enable licensed features.
Note:
You can enable FTP or TFTP in the boot config flags and then initiate an FTP or a TFTP
session from your workstation to put the file on the server running on the switch.
Procedure
1. From a remote station, or PC, use FTP or TFTP to download the license file to the device,
and store the license file in the /intflash directory.
2. Enter Global Configuration mode:
enable
configure terminal
3. To load the license file, execute the following command:
load-license
Important:
If the loading fails, or if the switch restarts and cannot locate a license file in the specified
location, the switch cannot unlock the licensed features and reverts to base functionality.
Licensing
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 122
Comments on this document? infodev@avaya.com