Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this release
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements using ACLI
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Detail field descriptions
Use the data in the following table to use the Detail tab.
Name Description
Type Describes the type of power used—AC or DC.
Description Provides a description of the power supply.
SerialNumber Specifies the power supply serial number.
HardwareRevision Specifies the hardware revision number.
PartNumber Specifies the power supply part number.
PowerSupplyOperStatus Specifies the status of the power supply as one of the following:
• on (up)
• off (down)
InputLineVoltage Display the input line voltage:
• low 110v—power supply connected to a 110 Volt source
• high 220v—power supply connected to a 220 Volt source
• ac110vOr220v—power supply connected to a 110 Volt or 220
Volt source
If the power supplies in a chassis are not of identical input line
voltage values, the operating line voltage shows the low 110v
value.
OutputWatts Displays the output power of this power supply.
Viewing temperature on the chassis
You can view information about the temperature on the chassis.
About this task
The system triggers an alarm when one of the zones exceeds the threshold temperature value, and
clears the alarm after the zone temperature falls below the threshold value.
When an elevated temperature triggers a temperature alarm, the fan speed increases, and the LED
color changes on the front panel of the switch.
Procedure
1. In the Device Physical View tab, select the chassis.
2. In the navigation tree, expand the following folders: Configuration > Edit.
3. Click Chassis.
Viewing temperature on the chassis
October 2015 Administering Avaya VSP 7200 Series and 8000 Series 111
Comments on this document? infodev@avaya.com