Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this document
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Enabling or disabling the USB port
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Secure Shell fundamentals
- Secure Shell configuration using ACLI
- Downloading the software
- Enabling the SSHv2 server
- Changing the SSH server authentication mode
- Setting SSH configuration parameters
- Verifying and displaying SSH configuration information
- Connecting to a remote host using the SSH client
- Generating user key files
- Managing an SSL certificate
- Disabling SFTP without disabling SSH
- Enabling SSH rekey
- Configuring SSH rekey data-limit
- Configuring SSH rekey time-interval
- Displaying SSH rekey information
- Downgrading or upgrading from releases that support different key sizes
- Secure Shell configuration using Enterprise Device Manager
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Name Description
Type Specifies the chassis type.
SerialNumber Specifies a unique chassis serial number.
HardwareRevision Specifies the current hardware revision of the device chassis.
NumSlots Specifies the number of slots available in the chassis:
• VSP 7200 Series 2 slots
• VSP 8200: 1 slot
• VSP 8400: 4 slots
NumPorts Specifies the number of ports currently installed in the chassis.
BaseMacAddr Specifies the starting point of the block of MAC addresses used
by the switch for logical and physical interfaces.
MacAddrCapacity Specifies the number of routable MAC addresses based on the
BaseMacAddr.
AutoRecoverDelay Specifies the time interval, in seconds, after which auto-
recovery runs on ports to clear actions taken by CP Limit or link
flap. The default is 30.
MTUSize Configures the maximum transmission unit size. The default is
1950.
MgidUsageVlanCurrent Number of MGIDs for VLANs currently in use.
MgidUsageVlanRemaining Number of remaining MGIDs for VLANs.
MgidUsageMulticastCurrent Number of MGIDs for multicast currently in use.
MgidUsageMulticastRemaining Number of remaining MGIDs for multicast.
DdmMonitor Enables or disables the monitoring of the DDM. When enabled,
the user gets the internal performance condition (temperature,
voltage, bias, Tx power and Rx power) of the SFP/XFP. The
default is disable.
DdmMonitorInterval Configures the DDM monitor interval in the range of 5 to 60 in
seconds. If any alarm occurs, the user gets the log message
before the specific interval configured by the user. The default
value is 5 seconds.
DdmTrapSend Enables or disables the sending of trap messages. When
enabled, the trap message is sent to the Device manager, any
time the alarm occurs. The default is enable.
DdmAlarmPortdown Sets the port down when an alarm occurs. When enabled, the
port goes down when any alarm occurs. The default is disable.
PowerUsage Specifies the amount of power the CPU uses.
PowerAvailable Specifies the amount of power available to the CPU.
Chassis operations
January 2017 Administering Avaya VSP 7200 Series and 8000 Series 88
Comments on this document? infodev@avaya.com