Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this document
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Enabling or disabling the USB port
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Secure Shell fundamentals
- Secure Shell configuration using ACLI
- Downloading the software
- Enabling the SSHv2 server
- Changing the SSH server authentication mode
- Setting SSH configuration parameters
- Verifying and displaying SSH configuration information
- Connecting to a remote host using the SSH client
- Generating user key files
- Managing an SSL certificate
- Disabling SFTP without disabling SSH
- Enabling SSH rekey
- Configuring SSH rekey data-limit
- Configuring SSH rekey time-interval
- Displaying SSH rekey information
- Downgrading or upgrading from releases that support different key sizes
- Secure Shell configuration using Enterprise Device Manager
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
4. Specify the username and password for the appropriate access level.
5. Click Apply.
Configuring the logon banner
About this task
Configure the logon banner using EDM to display a warning message to users of the CLI before
authentication.
Procedure
1. In the navigation tree, open the following folders: Configuration > Security > Control Path.
2. Click General.
3. Click the CLI tab.
4. Enter the banner text in the CustomBannerText field.
5. Check the CustomBannerEnable check box.
6. Click Apply.
CLI field descriptions
Use the data in the following table to use the CLI tab.
Name
Description
RWAUserName Specifies the user name for the read-write-all CLI account.
RWAPassword Specifies the password for the read-write-all CLI account.
RWEnable Activates the read-write access. The default is enabled.
RWUserName Specifies the user name for the read-write CLI account.
RWPassword Specifies the password for the read-write CLI account.
RWL3Enable Activates the read-write Layer 3 access. The default is enabled.
RWL3UserName Specifies the user name for the Layer 3 read-write CLI account.
RWL3Password Specifies the password for the Layer 3 read-write CLI account.
RWL2Enable Activates the read-write Layer 2 access. The default is enabled.
RWL2UserName Specifies the user name for the Layer 2 read-write CLI account.
RWL2Password Specifies the password for the Layer 2 read-write CLI account.
RWL1Enable Activates the read-write Layer 1 access. The default is enabled.
RWL1UserName Specifies the user name for the Layer 1 read-write CLI account.
RWL1Password Specifies the password for the Layer 1 read-write CLI account.
ROEnable Activates the read-only CLI account. The default is enabled.
ROUserName Specifies the user name for the read-only CLI account.
ROPassword Specifies the password for the read-only CLI account.
Table continues…
System access
January 2017 Administering Avaya VSP 7200 Series and 8000 Series 212
Comments on this document? infodev@avaya.com