Admin Guide
Table Of Contents
- Contents
- Chapter 1: Introduction
- Chapter 2: New in this document
- Chapter 3: Basic administration
- Chapter 4: System startup fundamentals
- Chapter 5: Boot parameter configuration using ACLI
- Chapter 6: Run-time process management using ACLI
- Chapter 7: Chassis operations
- Chassis operations fundamentals
- Chassis operations configuration using ACLI
- Enabling jumbo frames
- Configuring port lock
- Configuring SONMP
- Viewing the topology message status
- Associating a port to a VRF instance
- Configuring an IP address for the management port
- Configuring Ethernet ports with Autonegotiation
- Enabling channelization
- Configuring serial management port dropping
- Controlling slot power
- Enabling or disabling the USB port
- Chassis operations configuration using EDM
- Editing system information
- Editing chassis information
- Configuring system flags
- Configuring channelization
- Configuring basic port parameters
- Viewing the boot configuration
- Configuring boot flags
- Enabling Jumbo frames
- Configuring the date and time
- Associating a port to a VRF instance
- Configuring CP Limit
- Configuring an IP address for the management port
- Editing the management port parameters
- Configuring the management port IPv6 interface parameters
- Configuring management port IPv6 addresses
- Auto reactivating the port of the SLPP shutdown
- Editing serial port parameters
- Enabling port lock
- Locking a port
- Viewing power information
- Viewing power status on VSP 8400
- Viewing fan information
- Viewing topology status information
- Viewing the topology message status
- Configuring a forced message control pattern
- Chapter 8: Hardware status using EDM
- Chapter 9: Domain Name Service
- Chapter 10: Licensing
- Chapter 11: Network Time Protocol
- Chapter 12: Secure Shell
- Secure Shell fundamentals
- Secure Shell configuration using ACLI
- Downloading the software
- Enabling the SSHv2 server
- Changing the SSH server authentication mode
- Setting SSH configuration parameters
- Verifying and displaying SSH configuration information
- Connecting to a remote host using the SSH client
- Generating user key files
- Managing an SSL certificate
- Disabling SFTP without disabling SSH
- Enabling SSH rekey
- Configuring SSH rekey data-limit
- Configuring SSH rekey time-interval
- Displaying SSH rekey information
- Downgrading or upgrading from releases that support different key sizes
- Secure Shell configuration using Enterprise Device Manager
- Chapter 13: System access
- System access fundamentals
- System access configuration using ACLI
- Enabling ACLI access levels
- Changing passwords
- Configuring an access policy
- Specifying a name for an access policy
- Allowing a network access to the switch
- Configuring access policies by MAC address
- System access security enhancements
- Displaying the boot config flags status
- Enabling enhanced secure mode
- Creating accounts for different access levels
- Deleting accounts in enhanced secure mode
- Configuring a password for a specific user
- Returning the system to the factory defaults
- Configuring the password complexity rule
- Configuring the password length rule
- Configuring the change interval rule
- Configuring the reuse rule
- Configuring the maximum number of sessions
- Configuring the maximum age rule
- Configuring the pre- and post-notification rule
- System access configuration using EDM
- Chapter 14: ACLI show command reference
- Access, logon names, and passwords
- Basic switch configuration
- Current switch configuration
- CLI settings
- Ftp-access sessions
- Hardware information
- NTP server statistics
- Power summary
- Power information for power supplies
- System information
- System status (detailed)
- Telnet-access sessions
- Users logged on
- Port egress COS queue statistics
- CPU queue statistics
- Chapter 15: Port numbering and MAC address assignment reference
- Chapter 16: Supported standards, RFCs, and MIBs
- Glossary
Name Description
Note:
The 10 GigabitEthernet fiber-based I/O module ports can operate at
either 1 Gigabit per second (Gbps) or 10 Gbps, dependent upon the
capabilities optical transceiver that you install.
This presents an ambiguity with respect to the autonegotiation
settings of the port, while 1 Gigabit Ethernet (GbE) ports require
autonegotiation; autonegotiation is not defined and is non-existent for
10 GbE ports.
For a 10GbE fiber-based I/O module, you have the capability to swap
back-and-forth between 1 GbE and 10 GbE operation by simply
swapping transceivers. To help with this transition between 1 GbE
and 10 GbE port operation, Avaya allows you to configure
autonegotiation when you install a 10 GbE transceiver, even though
autonegotiation is not defined for 10GbE.
You can do this in anticipation of a port changeover from 10 GbE to 1
GbE. In this manner, you could essentially preconfigure a port in 1
GbE mode while the 10 GbE transceiver is still installed. The port is
ready to go upon the changeover to the 1 GbE transceiver.
In addition, you can use a saved configuration file with autonegotiation
enabled to boot a system with either 10 GbE or 1 GbE transceivers
installed. If you install a 1 GbE transceiver, the system applies
autonegotiation. If you install a 10 GbE transceiver, the system does
not remove the autonegotiation settings from the configuration, but the
system simply ignores the configuration because autonegotiation
settings are irrelevant to a 10 GbE transceiver. The system preserves
the saved configuration for autonegotiation when resaved no matter
which speed of transceiver you install.
AdminDuplex
Specifies the administrative duplex mode for the management port. The
default is full.
OperDuplex Specifies the operational duplex configuration for this port.
AdminSpeed Specifies the administrative speed for this port. The default is 100 Mb/s.
OperSpeed Shows the current operating data rate of the port.
Configuring the management port IPv6 interface parameters
About this task
Configure IPv6 management port parameters to use IPv6 routing on the port.
This procedure only applies to hardware with a dedicated, physical management interface.
Procedure
1. In the Device Physical View tab, select the management port.
Chassis operations
January 2017 Administering Avaya VSP 7200 Series and 8000 Series 104
Comments on this document? infodev@avaya.com