Installation Instructions

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesFabric-enabled multi-service edge switches

Table Of Contents

Installation Job Aid for VSP 4450GSX

Series

Release 6.1.0.0

NN46251-309

Issue 03.01

November 2017

Notices

Notice paragraphs alert you about issues that require your attention. The following paragraphs

describe the types of notices used in this guide.

Note:

Notes provide tips and useful information regarding the installation and operation of products.

Electrostatic alert:

ESD

ESD notices provide information about how to avoid discharge of static electricity and

subsequent damage to products.

Caution:

Caution notices provide information about how to avoid possible service disruption or damage to

products.

Warning:

Warning notices provide information about how to avoid personal injury when working with

products.

Voltage:

Danger — High Voltage notices provide information about how to avoid a situation or condition

that can cause serious personal injury or death from high voltage or electric shock.

2017, Extreme Networks, Inc.

Summary of content (12 pages)

PAGE 1
Installation Job Aid for VSP 4450GSX Series Release 6.1.0.0 NN46251-309 Issue 03.01 November 2017 Notices Notice paragraphs alert you about issues that require your attention. The following paragraphs describe the types of notices used in this guide. Note: Notes provide tips and useful information regarding the installation and operation of products. Electrostatic alert: ESD ESD notices provide information about how to avoid discharge of static electricity and subsequent damage to products.
PAGE 2
Danger: Danger notices provide information about how to avoid a situation or condition that can cause serious personal injury or death. Safety messages Warning: Installation must be performed by qualified service personnel only. Read and follow all warning notices and instructions marked on the product or included in the documentation. Voltage: This equipment relies on the building's installation for overcurrent protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15 A U.S.
PAGE 3
Caution: Risk of high current and board burn out if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Warning: The lithium battery is not field replaceable. It must only be removed and replaced by authorized personnel. Contact Technical Support for assistance if the battery requires replacement.
PAGE 4
Installing the VSP 4000 switch on a table or shelf You can install a single VSP 4000 switch on any flat surface. The surface must support the combined weight of the switch and attached cables (from 15 and 20 pounds [7 to 9 kilograms]). To install a VSP 4000 on a table or shelf, perform this procedure. 1. Attach the included rubber footpads on the bottom of the switch at the locations indicated. 2. Set the switch on a table or shelf as illustrated below. Allow at least 2 inches (5.
PAGE 5
Installing the VSP 4000 switch in an equipment rack To install a VSP 4000 switch in an equipment rack, perform this procedure. Prerequisites for installing the Virtual Services Platform 4000 in an equipment rack: • Ensure that you have a space of 1.75 inches (4.45 centimeters) in height for each switch in an EIA or IEC-standard 19-inch (48.2-centimeter) equipment rack. • The rack is bolted to the floor and braced if necessary.
PAGE 6
3. Insert and tighten the rack-mount screws. Installing SFP transceivers Install SFP transceivers by performing this procedure. 1. Remove the transceiver from the protective packaging. 2. Verify that the transceiver is the correct model for the network configuration. 3. Grasp the transceiver between your thumb and forefinger. 4. Insert the transceiver into the proper module on the switch. Apply a light pressure to the transceiver until it clicks and locks into position in the module. 5.
PAGE 7
3. Slide the transceiver from the module slot. 4. If the transceiver does not slide easily from the module slot, use a gentle side-to-side rocking motion while firmly pulling the transceiver from the slot. 5. Attach a dust cover over the fiber-optic bores and store the transceiver in a safe place until you need it. Important: Discard transceivers in accordance with the proper laws and regulations.
PAGE 8
Power supply power specifications for the VSP 4450GSX series switches The VSP 4450GSX series switches support two external field replaceable AC and DC power supplies. One power supply ships with the chassis. You can install a secondary power supply to provide redundancy, load sharing, and to add Power over Ethernet Plus (PoE+) power budget on PWR+ models.
PAGE 9
Power over Ethernet Plus (PoE+) specifications Table 2: VSP 4450GSX-PWR+ PoE+ specifications Maximum PoE+ W Average PoE+ W on 12 ports 835W with one power supply 17.8W or 32.4W (802.3.at) — 1 power supply 1835W with two power supplies • The VSP 4450GSX-PWR+ can support 802.3af 17.8W or 32.4W on each port with one power supply installed. You can add a second power supply for redundancy. DC power supply specifications The VSP 4450GSX-DC switch uses field replaceable 300W DC PSUs.
PAGE 10
Installing the Virtual Services Platform 4000 power supply You must install at least one power supply before using the switch. VSP 4000 models support two field replaceable external power supplies. If supported, you can install an optional second power supply for redundancy, load sharing, or to provide additional PoE+ power budget. Perform the following procedure to install an external power supply into your switch. Note: VSP 4000 hardware can vary.
PAGE 11
Table 5: International power cord specifications Country and Plug Specification Specifications Continental Europe: • 220 or 230VAC • CEE7 standard VII male plug • 50 Hz • Harmonized cord (HAR marking on the outside of the cord jacket to comply with the CENELEC Harmonized Document HD-21) • Single phase United States of America, Canada, and Japan: • 100 or 120VAC • NEMA5-15P male plug • 50–60 Hz • UL-recognized (UL stamped on cord jacket) • Single phase Typical Plug • CSA-certified (CSA label s
PAGE 12
Figure 3: DC power cable Figure 4: DC power cord housing unit with terminals November 2017 Installation Job Aid for VSP 4450GSX Series 12