Design Reference

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesFabric-enabled multi-service edge switches

161

162

163

164

165

166

167

168

169

170

Table Of Contents

Contents
Chapter 1: Introduction
- Purpose
- Related resources
- Support
Chapter 2: New in this release
- VOSS 4.2.1
  - Features
  - Other changes
- VOSS 4.2
  - Features
  - Other changes
Chapter 3: Network design fundamentals
Chapter 4: Hardware fundamentals and guidelines
- Supported hardware
- Platform considerations
- Hardware compatibility for VSP 4000
- Supported optical devices
- Dispersion considerations for long reach
- 10/100BASE-X and 1000BASE-TX reach
- 10/100/1000BASE-TX Auto-Negotiation recommendations
- Auto MDIX
- CANA
Chapter 5: Optical routing design
- Optical routing system components
Chapter 6: Platform redundancy
- Power redundancy
- Input/output port redundancy
- Configuration redundancy
- Link redundancy
Chapter 7: Link redundancy
- Physical layer redundancy
- MultiLink Trunking
- 802.3ad-based link aggregation
Chapter 8: Layer 2 loop prevention
- Loop prevention and detection
- SLPP example scenarios
Chapter 9: Layer 2 switch clustering and SMLT
- Split MultiLink Trunk configuration
Chapter 10: Layer 3 switch clustering and RSMLT
- Routed SMLT
- Switch clustering topologies and interoperability with other products
Chapter 11: Layer 3 switch clustering and multicast SMLT
- General guidelines
- Multicast triangle topology
- Square and full-mesh topology multicast guidelines
- SMLT and multicast traffic issues
Chapter 12: Spanning tree
- Spanning tree and protection against isolated VLANs
- MSTP and RSTP considerations
Chapter 13: Layer 3 network design
- VRF Lite
- Virtual Router Redundancy Protocol
- Open Shortest Path First
- Border Gateway Protocol
- IP routed interface scaling
- IPv6
Chapter 14: SPBM design guidelines
- 802.1aq standard
- VLANs without member ports
- Provisioning
- Implementation options
- Reference architectures
- Solution-specific reference architectures
- Best practices
- SPBM restrictions and limitations
- IP multicast over Fabric Connect restrictions
Chapter 15: IP multicast network design
- Multicast and VRF-Lite
- Multicast and MultiLink Trunking considerations
- Multicast scalability design rules
- IP multicast address range restrictions
- Multicast MAC address mapping considerations
- Dynamic multicast configuration changes
- IGMPv3 backward compatibility
- IGMP Layer 2 Querier
- TTL in IP multicast packets
- Multicast MAC filtering
- Guidelines for multicast access policies
- Split-subnet and multicast
- Protocol Independent Multicast-Sparse Mode guidelines
- Protocol Independent Multicast-Source Specific Multicast guidelines
- Multicast for multimedia
Chapter 16: System and network stability and security
- DoS protection mechanisms
- Damage prevention
- Data plane security
- Control plane security
- Additional information
Chapter 17: QoS design guidelines
- QoS mechanisms
- QoS interface considerations
- Network congestion and QoS design
- QoS examples and recommendations
Chapter 18: Layer 1, 2, and 3 design examples
- Layer 1 example
- Layer 2 example
- Layer 3 example
Glossary

Figure 82: RPR QoS internetworking

Routed traffic

If you route traffic over the core network, VLANs are not kept separate.

If you configure the port to core, you assume that, for all incoming traffic, the QoS configuration is

properly marked. All core switch ports simply read and forward packets. The switch does not re-

mark or classify the packets. The customer device or the edge devices perform all initial QoS

markings.

The following figure shows the actions performed on three different routed traffic flows (that is VoIP,

video conference, and email) at access and core ports throughout the network.

QoS design guidelines

168 Network Design Reference for Avaya VSP 4000 Series June 2015

Comments on this document? infodev@avaya.com