Quick Install Guide

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesFabric-enabled multi-service edge switches

Commissioning the VSP 4000

Property Value

Baud Rate 9600 bps

Data Bits 8

Stop Bits 1

Parity None

Flow Control None

http://support.avaya.com

1-800-242-2121 (U.S.A.)

1-866 GO-AVAYA

1-866-462-8292 (US Sales)

Poster part number: 700508202

Release 4.0

NN46251-302, 02.02

Caution: Before you unplug the AC power cord, always

perform the following shutdown procedure. This procedure

flushes any pending data to ensure data integrity.

1. Enter the Privileged EXEC command mode:

enable

2. Shutdown the VSP 4000:

sys shutdown

3. Before you unplug the power cord, wait until you see the

following message:

System Halted, OK to turn off power.

For more information on this and other administration

procedures, see Avaya Virtual Services Platform 4000

Administration (NN46251-600).

Connect the AC power cord to the back of the switch, and then

plug the other end of the cord into an AC power outlet.

Note: You will need two power cords if you have installed a

redundant PSU.

Warning: You must use a power cord set approved for the 4000

Series switch and the power receptacle type in your country.

Check the front-panel LEDs as the device powers on to be sure

the PWR LED is lit. If not, check if the power cord is plugged in

correctly. The switch will power on immediately when it is

connected to a suitable AC power source.

Power Up

Note: Before installing, ensure the switch is up and running, and

operating normally. Verify that the SFP or SFP+ transceivers and

network cabling support your network configuration.

1. Remove the transceiver from the protective packaging.

2. Verify that the transceiver is the correct model for the

network configuration.

3. Grasp the transceiver between your thumb and forefinger.

4. Insert the transceiver into the proper SFP/SFP+ slot on the

switch as illustrated. Apply a light pressure to the transceiver

until it clicks and locks into position in the slot.

Install SFP and SFP+ transceivers

Console port cabling specifications:

Ensure the use of Category 5E or higher specification cabling

for 1 Gbps/1000 Mbps operation. RJ-45 console port cables

are as follows:

Connector Pin Number Signal

Carrier detect (not used)

Transmit Data (TXD)

Receive Data (RXD)

Data terminal ready (not used)

Signal ground (GND)

Not used

Request to send (not used)

Not used

Ring indicator (not used)

RJ–45 Console port pin assignments

Connector Pin Number Signal

Ready to send (RTS) — optional

Data terminal ready (DTR) —

optional, can swap or link with pin 8

Transmit data (TXD) — mandatory

Carrier detect (DCD) — optional

Ground (GND) — mandatory

Receive data (RXD) — mandatory

Data set ready (DSR) — optional

8 Clear to send (CTS) — optional,

can swap or link with pin 1.

Note: In the following procedure you create a VLAN with

ID 20 and name Avaya.

1. Create a VLAN:

VSP-4850GTS-PWR+:1(config)#vlan

create 20 name Avaya type port

2. Add VLAN members:

VSP-4850GTS-PWR+:1(config)#vlan members add 20 1/4

3. Configure a management IP interface for the VLAN

(for example, 47.17.123.85)

VSP-4850GTS-PWR+:1(config)#interface vlan 20

VSP-4850GTS-PWR+:1(config)#ip address

47.17.123.85 255.255.255.0

1. Connect the console cable from the terminal to the console

port of the switch to allow initial configuration. Any terminal

or PC with the appropriate terminal emulator can be used as

the management station.

2. Set the terminal protocol on the terminal or terminal

emulation program to VT100 or VT100/ANSI.

3. Connect to the switch using the terminal or terminal

emulation application.

Terminal emulation settings

PEC Code Name Short Description

Avaya RJ-45/DB-9

CONSOLE CABLE

The VSP 4000 has an RJ-45 female

connector, so a serial cable with

RJ-45 connectors, or a serial cable

with a DB-9 female connector on

one end and an RJ-45 on the other

is appropriate.

The maximum length for the console

port cable is 25 feet (8.3 meters).

Converts DB-9 MALE to RJ-45 serial

port. The adaptor can be used for

PC or device with DB-9 MALE

console port. Also, can be used with

Category 5 RJ-45 straight cable to

provide console connection.

Converts DB-9 FEMALE to RJ-45

serial port. This adaptor can be used

to convert DB-9 of AL2011013-E6

console cable to RJ-45.

AL2011022-E6

AVAYA RED DB-9

FEMALE TO

RJ-45 ADAPTOR

AL2011020-E6

AVAYA BLUE

DB-9 MALE TO

RJ-45 ADAPTOR

AL2011021-E6

On your VSP 4000 switch, the console port is the RJ-45 port

outlined with a blue border on the front of your switch (note

orientation). Use an RJ-45 to DB-9 cable to connect the switch

console port to your management terminal. Use adaptors to

provide different connection options. The maximum length of a

console cable is 25 feet (8.3 meters). The following tables

describe the RJ-45 and DB-9 console port pin-out information.

You can use the pin-out information to verify or create a

console cable for use with your maintenance terminal.

DB–9 Console port pin assignments

Connect the console cable to the VSP 4000

Configure an in-band VLAN and a

management IP interface for the VLAN

For more information, go to http://support.avaya.com and

download the following VSP 4000 guides:

•

Regulatory Information and

Locating the Document (NN46251-105)

•

Documentation Roadmap (NN46251-100)

•

Installation (NN46251-300)

•

Quick Start (NN46251-102)

•

Release Notes (NN46251-401)

•

Administration (NN46251-600)

Shutting down the VSP 4000