Installation Guide
Table Of Contents
- Extreme SLX 9850-4 Router Hardware Installation Guide
- Preface
- About this Document
- Device Overview
- Preparing for the Installation
- Mounting the Device
- Initial Setup and Verification
- Initial setup and configuration checklist
- Items required
- Providing power to the device
- Establishing a serial connection
- Configuring a static IP address
- Establishing an Ethernet connection
- Customizing the chassis and host names
- Configuring the DNS service
- Setting the date and time
- Verifying correct operation
- Backing up the configuration
- Powering down the device
- Installing cable management kit
- Monitoring the Device
- Management Modules
- Interface Modules
- Power Supply Modules
- Power supply module overview
- Precautions specific to the power supply module
- Time and items required for removal and replacement
- Removing an AC power supply module
- Inserting an AC power supply module
- Removing a DC power supply module
- Inserting a DC power supply module
- Verifying power supply module operation
- High Voltage Power Supply Unit supporting AC and DC Voltages
- Fan Modules
- Switch Fabric Modules
- Transceivers and cables
- Supported transceivers and cables
- Time and items required
- Precautions specific to transceivers and cables
- Cleaning the fiber-optic connectors
- Managing cables
- Installing an SFP+ transceiver
- Replacing an SFP+ transceiver
- Installing a QSFP28 transceiver
- Replacing a QSFP28 transceiver
- Breakout cables
- Verifying transceiver operation
- Hardware Maintenance Schedule
- Brocade SLX 9850 Router Technical Specifications
- System specifications
- Ethernet
- LEDs
- Other
- Weight and physical dimensions
- Environmental requirements
- Power supply specifications (per PSU)
- Power consumption (typical configuration)
- Power consumption (maximum configuration)
- Power consumption (modules) (typical configuration)
- Power consumption (modules) (maximum configuration)
- Data port specifications (Ethernet)
- Serial port specifications (pinout RJ-45)
- Serial port specifications (protocol)
- Memory specifications
- Regulatory compliance (EMC)
- Regulatory compliance (safety)
- Regulatory compliance (environmental)
- Regulatory Statements
- Cautions and Danger Notices
TABLE 7 Supported transceivers and cables (continued)
Interface module Transceiver type and description Introduced OS Currently supported
10G-SFPP-LR - 10GBASE-LR, SFP+ optic (LC), for up to
10km over SMF
SLX-OS 16r.1.00 Yes
10G-SFPP-LR-8 - 10GBASE-LR,SFPP SMF LC
CONNECTOR 8-PACK
SLX-OS 16r.1.00 Yes
10G-SFPP-ER - 10GBASE-ER SFP+ optic (LC), for up to
40km over SMF
SLX-OS 16r.1.00 Yes
10G-SFPP-TWX-0101 - DIRECT ATTACHED SFPP
ACTIVE COPPER,1M,1-PACK
SLX-OS 16r.1.01 Yes
10G-SFPP-TWX-0108 - DIRECT ATTACHED SFPP
COPPER,1M,8-PACK
SLX-OS 16r.1.01 Yes
10G-SFPP-TWX-0301 - DIRECT ATTACHED SFPP
ACTIVE COPPER,3M,1-PACK
SLX-OS 16r.1.01 Yes
10G-SFPP-TWX-0308 - DIRECT ATTACHED SFPP
COPPER,3M,8-PACK
SLX-OS 16r.1.01 Yes
10G-SFPP-TWX-0501 - DIRECT ATTACHED SFPP
ACTIVE COPPER,5M,1-PACK
SLX-OS 16r.1.01 Yes
10G-SFPP-TWX-0508 - DIRECT ATTACHED SFPP
COPPER,5M,8-PACK
SLX-OS 16r.1.01 Yes
E1MG-LX-OM - 1000Base-LX SFP optic, SMF, LC
connector, Optical Monitoring Capable
SLX-OS 16r.1.00 Yes
E1MG-LX-OM-8 - 1000Base-LX SFP optic 8 Pack, SMF,
LC connector, Optical Monitoring Capable
SLX-OS 16r.1.00 Yes
E1MG-SX-OM - 1000Base-SX SFP optic, MMF, LC
connector, Optical Monitoring Capable
SLX-OS 16r.1.00 Yes
E1MG-SX-OM - 1000Base-SX SFP optic, MMF, LC
connector, Optical Monitoring Capable
SLX-OS 16r.1.00 Yes
E1MG-SX-OM-8 - 1000Base-SX SFP optic 8 Pack,
MMF, LC connector, Optical Monitoring Capable
SLX-OS 16r.1.00 Yes
E1MG-BXD - 1000Base-BXD SFP optic SMF, transmits
at 1490nm and receives at 1310nm, LC connector,single
strand SMF ber. This optic should only be connected to an
E1MG-BXU at the far end.
SLX-OS 16r.1.00 Yes
E1MG-BXU - 1000Base-BXU SFP optic SMF, transmits
at 1310nm and receives at 1490nm, LC connector,single
strand SMF ber. This optic should only be connected to an
E1MG-BXD at the far end.
SLX-OS 16r.1.00 Yes
XBR-000190 - FRU,SFP,1GE COPPER,1-PK, ROHS SLX-OS 16r.1.00 Yes
TABLE 8 Supported Brocade SLX 9850 power supply modules
Part number Long description Introduced OS Currently supported
XBR-SLX9850-ACPWR-3000 Brocade SLX 9850 AC 3000W power supply for
4-slot and 8-slot chassis, 90-132V, 180-264V
AC input
SLX-OS 16r.1.00 Yes
XBR-SLX9850-DCPWR-3000 Brocade SLX 9850 DC 3000W power supply for
4-slot and 8-slot chassis, 48V DC input
SLX-OS 16r.1.01 Yes
Supported hardware
Extreme SLX 9850-4 Router Hardware Installation Guide
14 53-1004399-07