Installation Guide
Table Of Contents
- ExtremeRouting SLX 9850-8 Hardware Installation Guide
- Preface
- About this Document
- Device Overview
- Preparing for the Installation
- Mounting the Device
- Initial Setup and Verification
- Initial setup and configuration checklist
- Items required
- Providing power to the device
- Establishing a serial connection
- Configuring a static IP address
- Establishing an Ethernet connection
- Customizing the chassis and host names
- Configuring the DNS service
- Setting the date and time
- Verifying correct operation
- Backing up the configuration
- Powering down the device
- Installing cable management kit
- Monitoring the Device
- Management Modules
- Interface Modules
- Power Supply Modules
- Power supply module overview
- Precautions specific to the power supply module
- Time and items required for removal and replacement
- Removing an AC power supply module
- Inserting an AC power supply module
- Removing a DC power supply module
- Inserting a DC power supply module
- Verifying power supply module operation
- High Voltage Power Supply Unit supporting AC and DC Voltages
- Fan Modules
- Switch Fabric Modules
- Transceivers and cables
- Supported transceivers and cables
- Time and items required
- Precautions specific to transceivers and cables
- Cleaning the fiber-optic connectors
- Managing cables
- Installing an SFP+ transceiver
- Replacing an SFP+ transceiver
- Installing a QSFP28 transceiver
- Replacing a QSFP28 transceiver
- Breakout cables
- Verifying transceiver operation
- Hardware Maintenance Schedule
- ExtremeRouting SLX 9850 Technical Specifications
- System specifications
- Ethernet
- LEDs
- Other
- Weight and physical dimensions
- Environmental requirements
- Power supply specifications (per PSU)
- Power consumption (typical configuration)
- Power consumption (maximum configuration)
- Power consumption (modules) (typical configuration)
- Power consumption (modules) (maximum configuration)
- Data port specifications (Ethernet)
- Serial port specifications (pinout RJ-45)
- Serial port specifications (protocol)
- Memory specifications
- Regulatory compliance (EMC)
- Regulatory compliance (safety)
- Regulatory compliance (environmental)
- Regulatory Statements
- Cautions and Danger Notices
NOTE
There are two sets of LEDs, one for the fan and one for the switch fabric module (SFM). This table describes both sets of LEDs.
TABLE 23 Fan module LED descriptions
LED purpose Color Status Recommended action
Power (Fan) No light (LED is o) Fan assembly does not have power. Ensure that the fan assembly is
rmly seated and has power.
Steady green Fan assembly has power. No action is required.
Status (Fan) No light (LED is o) Fan assembly is either healthy or
does not have power.
Ensure that the fan assembly has
power.
Steady amber Fan assembly is being initialized or
has a failure (full or partial).
Wait to see if the fan fully initializes.
If the LED remains amber, replace
the fan assembly.
Power (SFM) No light (LED is o) Module is not powered on. Ensure that the module is rmly
seated, that both ejectors are
pushed in fully, and that both
captive screws are tightened.
Green Module is operational. No action is required.
Status (SFM) No light (LED is o) Module is either not operational or
does not have power.
Ensure that the module is rmly
seated, that both ejectors (arms on
the side of the module) are pushed
in fully, and that both captive screws
are tightened.
Amber Module is faulty or initializing. Check the module status by
entering the show slots command.
If LED remains amber, consult the
device supplier.
Green Module is operational. No action is required.
Interpreting switch fabric module LEDs
Refer to the following illustrations and table to interpret the LED patterns for the switch fabric module (SFM). The LED patterns may
temporarily change during device diagnostic tests.
Since the SFM is located behind the fan modules, LEDs are provided on the fan and management modules to check SFM status. For
the location of the SFM LEDs on the management module, refer to Interpreting management module LEDs on page 75. For the
location of the SFM LEDs on the fan module, refer to Interpreting fan module LEDs on page 83.
There is also a label on the bottom center of the chassis that shows the SFM locations behind the fan modules.
If the fan module is removed, you can check the LEDs on the SFM, as shown in the following gure.
Interpreting switch fabric module LEDs
ExtremeRouting SLX 9850-8 Hardware Installation Guide
84 9035475-02 Rev AA