Installation Guide
Table Of Contents
- ExtremeRouting SLX 9850-8 Hardware Installation Guide
- Preface
- About this Document
- Device Overview
- Preparing for the Installation
- Mounting the Device
- Initial Setup and Verification
- Initial setup and configuration checklist
- Items required
- Providing power to the device
- Establishing a serial connection
- Configuring a static IP address
- Establishing an Ethernet connection
- Customizing the chassis and host names
- Configuring the DNS service
- Setting the date and time
- Verifying correct operation
- Backing up the configuration
- Powering down the device
- Installing cable management kit
- Monitoring the Device
- Management Modules
- Interface Modules
- Power Supply Modules
- Power supply module overview
- Precautions specific to the power supply module
- Time and items required for removal and replacement
- Removing an AC power supply module
- Inserting an AC power supply module
- Removing a DC power supply module
- Inserting a DC power supply module
- Verifying power supply module operation
- High Voltage Power Supply Unit supporting AC and DC Voltages
- Fan Modules
- Switch Fabric Modules
- Transceivers and cables
- Supported transceivers and cables
- Time and items required
- Precautions specific to transceivers and cables
- Cleaning the fiber-optic connectors
- Managing cables
- Installing an SFP+ transceiver
- Replacing an SFP+ transceiver
- Installing a QSFP28 transceiver
- Replacing a QSFP28 transceiver
- Breakout cables
- Verifying transceiver operation
- Hardware Maintenance Schedule
- ExtremeRouting SLX 9850 Technical Specifications
- System specifications
- Ethernet
- LEDs
- Other
- Weight and physical dimensions
- Environmental requirements
- Power supply specifications (per PSU)
- Power consumption (typical configuration)
- Power consumption (maximum configuration)
- Power consumption (modules) (typical configuration)
- Power consumption (modules) (maximum configuration)
- Data port specifications (Ethernet)
- Serial port specifications (pinout RJ-45)
- Serial port specifications (protocol)
- Memory specifications
- Regulatory compliance (EMC)
- Regulatory compliance (safety)
- Regulatory compliance (environmental)
- Regulatory Statements
- Cautions and Danger Notices
Interface cards are enabled and optics/Trac are at full line rate. Random packets, fans at nominal speed, ambient temperature 40 deg
C.
Conguration of SLX 9850-8: One 8-slot chassis with two management modules, six switch fabric modules, twelve power supplies,
three fan modules, and eight 36-port 100GbE, 60-port 40GbE, or 240-port 10GbE ex-speed interface modules set in 60x40 mode.
Interface cards are enabled and optics/Trac are at full line rate. Random packets, fans at nominal speed, ambient temperature 40 deg
C.
Model name Power used in watts Minimum number of power
supplies
Notes
SLX 9850-4 5947 2 200 VAC amps, watts, and BTU/hr
are calculated with 0.98 power
factor and 2 PSUs
SLX 9850-8 11492 4 200 VAC amps, watts, and BTU/hr
are calculated with 0.98 power
factor and 4 PSUs
Power consumption (modules) (typical conguration)
NOTE
Typical conguration is 50% trac with fans operating normally. Ambient temperature 25 deg
C.
Module Typical power consumption
Management Module 97 W
Switch Fabric Module SLX 9850-4: 102 W
SLX 9850-8: 200 W
Fan module SLX 9850-4: 175 W
SLX 9850-8: 346W
72-port 10GbE/1GbE interface module 250 W
36-port 100GbE, 60-port 40GbE, or 240-port
10GbE ex-speed interface module
617 W
Power consumption (modules) (maximum
conguration)
NOTE
Maximum conguration is 100% trac with fans operating normally. Ambient temperature 40 deg
C.
Module Maximum power consumption
Management Module 100W
Switch Fabric Module SLX 9850-4: 124 W
SLX 9850-8: 220 W
Fan module SLX 9850-4: 175 W
Power consumption (modules) (typical conguration)
ExtremeRouting SLX 9850-8 Hardware Installation Guide
136 9035475-02 Rev AA