Installation Guide
Table Of Contents
- Brocade SLX 9850-4 Router Hardware Installation Guide
- Preface
- About this Document
- Device Overview
- Preparing for the Installation
- Mounting the Device
- Initial Setup and Verification
- Initial setup and configuration checklist
- Items required
- Providing power to the device
- Establishing a serial connection
- Configuring a static IP address
- Establishing an Ethernet connection
- Customizing the chassis and host names
- Configuring the DNS service
- Setting the date and time
- Verifying correct operation
- Backing up the configuration
- Powering down the device
- Installing cable management kit
- Monitoring the Device
- Management Modules
- Interface Modules
- Power Supply Modules
- Power supply module overview
- Precautions specific to the power supply module
- Time and items required for removal and replacement
- Removing an AC power supply module
- Inserting an AC power supply module
- Removing a DC power supply module
- Inserting a DC power supply module
- Verifying power supply module operation
- High Voltage Power Supply Unit supporting AC and DC Voltages
- Fan Modules
- Switch Fabric Modules
- Transceivers and cables
- Supported transceivers and cables
- Time and items required
- Precautions specific to transceivers and cables
- Cleaning the fiber-optic connectors
- Managing cables
- Installing an SFP+ transceiver
- Replacing an SFP+ transceiver
- Installing a QSFP28 transceiver
- Replacing a QSFP28 transceiver
- Breakout cables
- Verifying transceiver operation
- Hardware Maintenance Schedule
- Brocade SLX 9850 Router Technical Specifications
- System specifications
- Ethernet
- LEDs
- Other
- Weight and physical dimensions
- Environmental requirements
- Power supply specifications (per PSU)
- Power consumption (typical configuration)
- Power consumption (maximum configuration)
- Power consumption (modules) (typical configuration)
- Power consumption (modules) (maximum configuration)
- Data port specifications (Ethernet)
- Serial port specifications (pinout RJ-45)
- Serial port specifications (protocol)
- Memory specifications
- Regulatory compliance (EMC)
- Regulatory compliance (safety)
- Regulatory compliance (environmental)
- Regulatory Statements
- Cautions and Danger Notices
DANGER Les procédures décrites dans ce manuel doivent être eectuées par un personnel de maintenance qualié.
PELIGRO Los procedimientos de este manual deben llevarlos a cabo técnicos cualicados.
Dangers related to equipment weight
DANGER
Use safe lifting practices when moving the product.
GEFAHR Beim Bewegen des Produktes ist auf eine sichere Hubtechnik zu achten.
DANGER Utiliser des techniques de levage sûres pour déplacer le produit.
PELIGRO Tenga mucho cuidado al levantar el producto para moverlo
DANGER
Mount the devices you install in a rack as low as possible. Place the heaviest device at the bottom and progressively place
lighter devices above.
GEFAHR Montieren Sie die Geräte im Gestell so tief wie möglich. Platzieren Sie das schwerste Gerät ganz unten, während leichtere
Geräte je nach Gewicht (je schwerer desto tiefer) darüber untergebracht werden.
DANGER Montez les dispositifs que vous installez dans un bâti aussi bas que possible. Placez le dispositif le plus lourd en bas et le plus
léger en haut, en plaçant tous les dispositifs progressivement de bas en haut du plus lourd au plus léger.
PELIGRO Monte los instrumentos que instale en un bastidor lo más bajos posible. Ponga el instrumento más pesado en la parte inferior
y los instrumentos progresivamente más livianos más arriba.
DANGER
Do not attempt to lift the chassis. It is extremely heavy. Use a mechanical lifting device to lift the chassis. Four or more
people are required to position the unpopulated chassis into the rack.
GEFAHR Nicht versuchen, ein Brocade SLX Chassis anzuheben. Es ist sehr schwer. Das Chassis mit Hilfe einer mechanischen
Hebevorrichtung anheben. Mindestens vier Personen sind erforderlich, um das unbeladene Chassis im Rack zu positionieren.
DANGER Ne jamais tenter de soulever un châssis Brocade SLX car il est alors extrêmement lourd. Pour soulever le châssis, utiliser un
appareil élévateur. Quatre personnes au moins sont nécessaires pour positionner dans le rack le châssis vidé de ses éléments.
PELIGRO No trate de levantar un chasis Brocade SLX. Es extremadamente pesado. Utilice un elevador mecánico para levantar el chasis.
Hacen falta cuatro personas o más para colocar el chasis no poblado en el interior del armazón.
DANGER
A fully populated Brocade SLX 9850-4 weighs approximately 137.4 kg (303 lb) and requires a hydraulic or assisted lift
to install it.
GEFAHR Ein vollständig bestückter Brocade SLX 9850-4 wiegt etwa 137.4 kg und erfordert zur Installation eine hydraulische oder
Servo-Hebevorrichtung.
DANGER Un commutateur Brocade SLX 9850-4 complet pèse environ 137.4 kg et requiert un dispositif de levage hydraulique ou
électrique pour l'installation.
PELIGRO Un Brocade SLX 9850-4 con la conguración completa pesa aproximadamente 137.4 kg (303 libras) y requiere un
elevador hidráulico o asistido para realizar su instalación.
Danger Notices
Brocade SLX 9850-4 Router Hardware Installation Guide
53-1004399-05 153