Installation Guide
Table Of Contents
- Contents
- About this Document
- Product Overview
- Installing a Brocade MLX Router
- Installation precautions
- Installing 2x100GbE interface modules in Brocade MLX routers
- Installing a Brocade MLX-4 router
- Installing a Brocade MLX-8 router
- Installing a Brocade MLX-16 router
- Installing a Brocade MLX-32 router
- Installing a Brocade MLX-32 router
- Preparing the installation site
- Brocade MLX-32 router shipping carton contents
- Unpacking your Brocade MLX-32 router
- Installing a Brocade MLX-32 router in a rack
- Installing Brocade MLX-32 router modules
- Brocade MLX-32 cable management
- Accessing modules for service
- Installing power supplies in a Brocade MLX-32 router
- Connecting AC power
- Connecting DC power
- Removing Brocade MLX-32 router DC power supplies
- Final steps
- Attaching a management station
- Activating the power source
- Verifying proper operation
- Installing a NetIron XMR Router
- Installation precautions
- Installing 2x100GbE interface modules in NetIron XMR routers
- Installing a NetIron XMR 4000 router
- Installing a NetIron XMR 8000 router
- Installing a NetIron XMR 16000 router
- Installing a NetIron XMR 32000 router
- Preparing the installation site
- Unpacking a NetIron XMR 32000 router
- Installing a NetIron XMR 32000 router in a rack
- Installing NetIron XMR 32000 modules
- NetIron XMR 32000 cable management
- Accessing modules for service
- Installing NetIron XMR 32000 router power supplies
- Removing NetIron XMR 32000 router DC power supplies
- Final steps
- Attaching a management station
- Activating the power source
- Verifying proper operation
- Using Brocade Structured Cabling Components
- Cable cinch overview
- mRJ21 procedures
- RJ45 procedures
- Cable cinch with one group of RJ45 cables
- Cable cinch with two groups of RJ45 cables
- Cable cinch with three groups of RJ45 cables
- Cable cinch with four groups of RJ45 cables
- Cable cinch with five groups of RJ45 cables
- Cable cinch with six groups of RJ45 cables
- Cable cinch with seven groups of RJ45 cables
- Cable cinch with eight groups of RJ45 cables
- Connecting a Router to a Network Device
- Managing Routers and Modules
- Managing the device
- Enabling and disabling a DC Power Source
- Disabling and re-enabling power to interface modules
- Monitoring I2C failures on management modules
- Displaying device status and temperature readings
- Displaying the Syslog configuration and static and dynamic buffers
- MP Presence from LP Detection (Headless Router Operation)
- Rolling Reboot
- Line Module Configuration Deletion in Interactive Boot Mode
- Managing switch fabric modules
- Managing the cooling system
- Managing interface modules
- Monitoring Link Status
- Using alarms to collect and monitor device status
- Displaying MR2 management module memory usage
- Enabling and disabling management module CPU usage calculations
- Displaying management module CPU usage
- Removing MAC address entries
- Simplified Upgrade
- Managing the device
- Maintenance and Field Replacement
- Hardware Specifications
- Regulatory Statements
- Caution and Danger Notices
Brocade MLX Series and Brocade NetIron XMR Installation Guide 301
53-1004195-03
Cautions
Table 0.12:
CAUTION Do not add or remove a flash card while a file operation involving the flash card slot is in
progress. Doing so can result in corruption of the flash card. If this occurs, you may need to
reformat the flash card to make it usable again. Reformatting the card erases all data stored
on the card.
VORSICHT Eine Flash-Karte darf nur dann eingesteckt oder herausgenommen werden, wenn keine
Dateifunktion läuft, die der Flash-Karte bedarf. Wenn dies nicht beachtet wird, kann dies zur
Korruption der Flash-Karte führen. Die Karte kann dann erst nach Neuformattierung wieder
benutzt werden. Bei Neuformattietung gehen alle auf der Karte gespeicherten Daten
verloren.
MISE EN GARDE
N'ajoutez pas ou ne supprimez pas une carte mémoire au cours d'une opération de fichier
dans laquelle le slot de carte mémoire est impliqué. Vous risquez sinon de corrompre la
carte mémoire. Si cela se produit, vous devrez peut-être reformater la carte mémoire pour
qu'elle soit à nouveau utilisable. Le reformatage de la carte efface toutes les données qui y
sont stockées.
PRECAUCIÓN
No añada ni quite una tarjeta flash mientras una operación de archivo que conlleve el uso de
una ranura de tarjeta flash se encuentre en uso. De hacerlo así se podría dar lugar a la
corrupción de la tarjeta flash. Si esto ocurriera, podría ser necesario que vuelva a formatear
la tarjeta flash para hacer que vuelva sea utilizable. Cuando se formatea la tarjeta se borran
todos los datos almacenados en la tarjeta.
Table 0.13:
CAUTION
Do not install the device in an environment where the operating ambient temperature might
exceed 40° C (104° F).
VORSICHT Das Gerät darf nicht in einer Umgebung mit einer Umgebungsbetriebstemperatur von über
40° C (104° F) installiert werden.
MISE EN GARDE N'installez pas le dispositif dans un environnement où la température d'exploitation
ambiante risque de dépasser 40° C (104° F).
PRECAUCIÓN No instale el instrumento en un entorno en el que la temperatura ambiente de operación
pueda exceder los 40° C (104° F).