Installation Guide
Table Of Contents
- Contents
- About this Document
- Product Overview
- Installing a Brocade MLX Router
- Installation precautions
- Installing 2x100GbE interface modules in Brocade MLX routers
- Installing a Brocade MLX-4 router
- Installing a Brocade MLX-8 router
- Installing a Brocade MLX-16 router
- Installing a Brocade MLX-32 router
- Installing a Brocade MLX-32 router
- Preparing the installation site
- Brocade MLX-32 router shipping carton contents
- Unpacking your Brocade MLX-32 router
- Installing a Brocade MLX-32 router in a rack
- Installing Brocade MLX-32 router modules
- Brocade MLX-32 cable management
- Accessing modules for service
- Installing power supplies in a Brocade MLX-32 router
- Connecting AC power
- Connecting DC power
- Removing Brocade MLX-32 router DC power supplies
- Final steps
- Attaching a management station
- Activating the power source
- Verifying proper operation
- Installing a NetIron XMR Router
- Installation precautions
- Installing 2x100GbE interface modules in NetIron XMR routers
- Installing a NetIron XMR 4000 router
- Installing a NetIron XMR 8000 router
- Installing a NetIron XMR 16000 router
- Installing a NetIron XMR 32000 router
- Preparing the installation site
- Unpacking a NetIron XMR 32000 router
- Installing a NetIron XMR 32000 router in a rack
- Installing NetIron XMR 32000 modules
- NetIron XMR 32000 cable management
- Accessing modules for service
- Installing NetIron XMR 32000 router power supplies
- Removing NetIron XMR 32000 router DC power supplies
- Final steps
- Attaching a management station
- Activating the power source
- Verifying proper operation
- Using Brocade Structured Cabling Components
- Cable cinch overview
- mRJ21 procedures
- RJ45 procedures
- Cable cinch with one group of RJ45 cables
- Cable cinch with two groups of RJ45 cables
- Cable cinch with three groups of RJ45 cables
- Cable cinch with four groups of RJ45 cables
- Cable cinch with five groups of RJ45 cables
- Cable cinch with six groups of RJ45 cables
- Cable cinch with seven groups of RJ45 cables
- Cable cinch with eight groups of RJ45 cables
- Connecting a Router to a Network Device
- Managing Routers and Modules
- Managing the device
- Enabling and disabling a DC Power Source
- Disabling and re-enabling power to interface modules
- Monitoring I2C failures on management modules
- Displaying device status and temperature readings
- Displaying the Syslog configuration and static and dynamic buffers
- MP Presence from LP Detection (Headless Router Operation)
- Rolling Reboot
- Line Module Configuration Deletion in Interactive Boot Mode
- Managing switch fabric modules
- Managing the cooling system
- Managing interface modules
- Monitoring Link Status
- Using alarms to collect and monitor device status
- Displaying MR2 management module memory usage
- Enabling and disabling management module CPU usage calculations
- Displaying management module CPU usage
- Removing MAC address entries
- Simplified Upgrade
- Managing the device
- Maintenance and Field Replacement
- Hardware Specifications
- Regulatory Statements
- Caution and Danger Notices
246 Brocade MLX Series and Brocade NetIron XMR Installation Guide
53-1004195-03
Displaying management module CPU usage
console 54 0
vlan 0 0
mac_mgr 38 0
mrp 0 0
vsrp 0 0
snms 71 0
rtm 640 0
rtm6 40 0
ip_tx 2478 0
rip 0 0
mpls 119 0
nht 0 0
mpls_glue 13 0
bgp 0 0
bgp_io 0 0
ospf 737 0
ospf_r_calc 0 0
isis 38 0
isis_spf 0 0
mcast 18 0
msdp 134 0
vrrp 0 0
ripng 0 0
ospf6 66 0
ospf6_rt 0 0
mcast6 7 0
bfd 0 0
l4 98 0
stp 0 0
gvrp_mgr 0 0
snmp 0 0
rmon 13 0
web 86 0
lacp 0 0
dot1x 0 0
dot1ag 7 0
hw_access 1049 0
ospf_msg_task 0 0
telnet_0 0 0
telnet_1 44 0
Syntax: show cpu
Displaying management module CPU usage
You can display the tasks handled by the management module and the amount of the management module CPU used by each task by
entering the show tasks command at any level of the CLI.
Brocade# show tasks
Task Name Pri State PC Stack Size CPU Usage(%) task id task vid
---------- --- ----- --------- -------- ----- --------- ------ -------
idle 0 run 00001904 040560a0 256 66 0 0
monitor 20 susp 0000c658 0404bd80 8192 0 0 0
int 16 susp 0000c658 04051f90 16384 0 0 0
timer 15 susp 0000c658 04055f90 16384 0 0 0
dbg 30 susp 0000c658 0404df10 8192 0 0 0
flash 17 susp 0000c658 0409cf98 8192 0 0 0
wd 31 susp 0000c658 0409af80 8192 0 0 0
boot 17 susp 0000c658 041dbe30 65536 0 0 0
main 3 susp 0000c658 2060cf38 65536 0 0 1
itc 6 susp 0000c658 20610af0 16384 0 0 1
tmr 5 susp 0000c658 206a7638 16384 0 0 1