Installation Guide
Table Of Contents
- Contents
- About this Document
- Product Overview
- Installing a Brocade MLX Router
- Installation precautions
- Installing 2x100GbE interface modules in Brocade MLX routers
- Installing a Brocade MLX-4 router
- Installing a Brocade MLX-8 router
- Installing a Brocade MLX-16 router
- Installing a Brocade MLX-32 router
- Installing a Brocade MLX-32 router
- Preparing the installation site
- Brocade MLX-32 router shipping carton contents
- Unpacking your Brocade MLX-32 router
- Installing a Brocade MLX-32 router in a rack
- Installing Brocade MLX-32 router modules
- Brocade MLX-32 cable management
- Accessing modules for service
- Installing power supplies in a Brocade MLX-32 router
- Connecting AC power
- Connecting DC power
- Removing Brocade MLX-32 router DC power supplies
- Final steps
- Attaching a management station
- Activating the power source
- Verifying proper operation
- Installing a NetIron XMR Router
- Installation precautions
- Installing 2x100GbE interface modules in NetIron XMR routers
- Installing a NetIron XMR 4000 router
- Installing a NetIron XMR 8000 router
- Installing a NetIron XMR 16000 router
- Installing a NetIron XMR 32000 router
- Preparing the installation site
- Unpacking a NetIron XMR 32000 router
- Installing a NetIron XMR 32000 router in a rack
- Installing NetIron XMR 32000 modules
- NetIron XMR 32000 cable management
- Accessing modules for service
- Installing NetIron XMR 32000 router power supplies
- Removing NetIron XMR 32000 router DC power supplies
- Final steps
- Attaching a management station
- Activating the power source
- Verifying proper operation
- Using Brocade Structured Cabling Components
- Cable cinch overview
- mRJ21 procedures
- RJ45 procedures
- Cable cinch with one group of RJ45 cables
- Cable cinch with two groups of RJ45 cables
- Cable cinch with three groups of RJ45 cables
- Cable cinch with four groups of RJ45 cables
- Cable cinch with five groups of RJ45 cables
- Cable cinch with six groups of RJ45 cables
- Cable cinch with seven groups of RJ45 cables
- Cable cinch with eight groups of RJ45 cables
- Connecting a Router to a Network Device
- Managing Routers and Modules
- Managing the device
- Enabling and disabling a DC Power Source
- Disabling and re-enabling power to interface modules
- Monitoring I2C failures on management modules
- Displaying device status and temperature readings
- Displaying the Syslog configuration and static and dynamic buffers
- MP Presence from LP Detection (Headless Router Operation)
- Rolling Reboot
- Line Module Configuration Deletion in Interactive Boot Mode
- Managing switch fabric modules
- Managing the cooling system
- Managing interface modules
- Monitoring Link Status
- Using alarms to collect and monitor device status
- Displaying MR2 management module memory usage
- Enabling and disabling management module CPU usage calculations
- Displaying management module CPU usage
- Removing MAC address entries
- Simplified Upgrade
- Managing the device
- Maintenance and Field Replacement
- Hardware Specifications
- Regulatory Statements
- Caution and Danger Notices
124 Brocade MLX Series and Brocade NetIron XMR Installation Guide
53-1004195-03
Verifying proper operation
AC power supplies
ACOK Green (steady) The power supply is
receiving power
from the AC power
source.
Off The power supply is not receiving power from an AC power
source You can do the following:
•
Make sure that the power cord is connected securely to the
wall outlet and the power supply.
•
Make sure the wall outlet is rated for high line, 200-240
VAC and 20A. If it is not, obtain a cable that is rated for the
outlet.
•
Make sure that the wall outlet has power.
DC OK Green (steady) The power supply is
providing AC power
to the router.
Off The power supply is not supplying power to the device. If the AC
LED is green, there is a problem with the power supply and it must
be replaced.
ALM Off The power supply is
in normal operating
condition.
Amber The power supply is malfunctioning.
DC power supplies
DC IN Green (steady) The power supply is
receiving power
from the DC power
source.
Off The power supply is not receiving power from a DC power source
You can do the following:
•
Make sure that the power supply cables are connected
securely to the power source and the power supply.
•
Make sure that the DC power source for MLX -4, -8, and
-16 is 48 VDC @ 30 A. The DC power source for MLX-32
must be 48 VDC @60A. The operating voltage range is 40
to 60 VDC.
•
Make sure that the power source has power.
DC OUT Green (steady) The power supply is
providing DC power
to the router.
Off The power supply is not supplying power to the device. If the DC
IN LED is green, then there is a problem with the power supply
and it must be replaced.
ALM Off The power supply is
in normal operating
condition.
Amber The power supply is malfunctioning.
TABLE 25 LED status and explanation (Continued)
LED label Desired state Meaning Abnormal
state
Meaning or action