Specifications

Open Issues, Known Behaviors, and Resolved Issues
ExtremeXOS 12.4.2 Release Notes
73
PD4-1095528349 The show access-list counters command does not return the proper values and
generates the following log message:
<Warn:HAL.IPv4ACL.SendSlotCfgMsgFail> MM-B: An operation to send
ACL configuration 7 to one or more slots failed with error
HAL_CNDT_ERR.
PD4-973196566 When downgrading from CR22 in ExtremeXOS 12.4.1 to CR 21 in ExtremeXOS 12.3.2.5,
multiple error and warning messages are displayed.
* (debug) BD-20808.5 # sh log sev err
12/01/1933 21:56:17.48 <Erro:HAL.Card.Error>
MM-B:voyagerCardPowerEnable:1153:- Invalid System mode
information returned from dm. dmGetSystemMode() = 33
12/01/1933 21:48:23.10 <Crit:HAL.Fabric.Critical> MM-A: Failed to
initilize Fabric Elements in Slot:
12/01/1933 21:48:23.10 <Crit:HAL.Fabric.Critical> MM-A:
fe200_init_fabriccard_1 FE-200 Power up Failed for Fabric Slot: 5
PD4-1215784550 I/O slots that are configured for a sys-recovery shutdown are not going to the shutdown
state when a hardware error occurs on the slot.
PD4-1347661196 Downgrade the firmware on the New Fan tray (Part No. 806023-00-01) to any firmware
lower than CR 24 (EXOS 12.4.2). This action will cause fan tray to go into failed state.
Perform 'install firmware verify' or 'install firmware' to upgrade the new fan tray. It will
ask to upgrade the firmware second time using 'install firmware verify' or 'install
firmware'. After the second firmware upgrade, sh fan will not show correct fan speed
unless the system is power cycled once to reboot both MMs to communicate with fan
trays properly.
PD4-1345813119 While upgrading firmware to CR 24 (EXOS 12.4.2) from any EXOS image lower than
12.4.2, the following error messages were seen in the log. * (pacman) BD-20808.5 # sh
log sev err 05/27/2010 14:42:53.39 <Crit:HAL.Fabric.Critical> MM-A:
pioneerBringDownFE200 Bringing Down FE200 on XBAR 5 as the command
EXTRUC_FE_WRITE_CMD Failed, Reason: UCPIPE_ERROR 05/27/2010 14:42:19.06
<Crit:HAL.Fabric.Critical> MM-A: pioneerBringDownFE200 Bringing Down FE200 on
XBAR 4 as the command EXTRUC_FE_WRITE_CMD Failed, Reason: UCPIPE_ERROR
05/27/2010 14:41:45.34 <Crit:HAL.Fabric.Critical> MM-A: pioneerBringDown
PD4-1357671191 The broadcast, Multicast and unknown unicast traffic does not get rate-limited in
accordance to the rate configured, when the configured rate in the meter is below
10Mbps. This issue applies only when trying to rate-limit unknown unicast, broadcast and
multicast by configuring using the below CLIS: conf rate-limit flood multicast-guaranteed
meter configure rate-limit flood multicast-best-effort meter
PD4-1168490821 While performing an install firmware using ExtremeXOS 12.4.1 from CR 17 (ExtremeXOS
12.2.2.11-patch1-3 firmware), the fan tray upgrade fails. Reinstall the firmware to
upgrade the fan tray to CR 23 with ExtremeXOS 12.4.1.The fan tray fails with the
following error message:
tftp: server error: (0) Wrong TFTP State
TFTP FAILED: TRAY 1, Fantray Secondary image
Fantray firmware installation failed for Tray-1
Error: Failed to install image -
PD4-667561942 The command output for the show fdb hardware command does not include the
blackhole MAC address.
PD4-757563008 After hot swapping an MM-A, the output for the show power budget command shows
the wrong power information.
PD4-717942168 FDB entries are not learned for L2 broadcast traffic after an MM failover.
Table 40: Platform-Specific and Feature PDs (Continued)
PD Number Description