User's Guide
Table Of Contents
- Table of Contents
- Preface
- Welcome to Extreme Campus Controller
- Dashboard
- Monitor
- Sites List
- Device List
- Access Points List
- Smart RF Widgets
- Switches List
- Networks List
- Clients
- Policy
- Configure
- Network Configuration Steps
- Sites
- Add a Site
- Modifying Site Configuration
- Site Location
- Adding Device Groups to a Site
- Add or Edit a Configuration Profile
- Associated Profiles
- Associated Networks
- Mesh Point Profile Configuration
- Configure Client Bridge
- Understand Radio Mode
- Radio as a Sensor
- Advanced AP Radio Settings
- VLAN Profile Settings
- AirDefense Profile Settings
- ExtremeLocation Profile Settings
- IoT Profile Settings
- Positioning Profile Settings
- Analytics Profile Settings
- RTLS Settings
- Advanced Configuration Profile Settings
- Configuring RF Management
- Configuring a Floor Plan
- Advanced Tab
- Devices
- Networks
- Policy
- Automatic Adoption
- ExtremeGuest Integration
- AAA RADIUS Authentication
- Onboard
- Onboard AAA Authentication
- Manage Captive Portal
- Manage Access Control Groups
- Access Control Rules
- Tools
- Administration
- System Configuration
- Manage Administrator Accounts
- Extreme Campus Controller Applications
- Product License
- Glossary
- Index
Support for ExtremeWireless AP3xx Access Points
Extreme Campus Controller supports the ExtremeWireless™ AP302W, AP305C, AP310i/e, AP310i-1
indoor access points and the AP305CX and AP360i/e outdoor access points.
Table 11: Radio Configuration and support for AP3xx
AP Model Radio Configuration
AP302W • Universal AP with two operating modes: on premise and
cloud-enabled. For more information, see Universal AP
Operational Modes on page 16.
• Radio Modes:
◦ Mode 1 — Dual-band concurrent operation
◦ Mode 2 — Radio 1 dual-band sensor, Radio 2 5GHz trac
forwarder
◦ Mode 3 — Radio 1 5GHz Low band, Radio 2 5GHz High
band trac forwarder
• Ports on the Universal APs are labeled with the prefix ETH.
◦ ETH0 — 1GHz Uplink port (No LAG or Layer 2 backup
function support.)
◦ ETH1, ETH2, ETH3 — Local network client wired ports.
◦ Pass-Through ports. Hardware wired ports, no software
support needed.
• PKI support, IPsec tunnel security
• Client Bridge is supported.
• Mesh Network is supported.
• Internet of things (IoT) devices are supported.
AP305C/CX • Universal AP with two operating modes: on premise and
cloud-enabled. For more information, see Universal AP
Operational Modes on page 16.
• 2.4/5GHz dual-band Sensor.
◦ Mode 1 — 2.4GHz service radio and 5GHz service radio
◦ Mode 3 — 5GHz lower band service radio and 5GHz
upper band service radio
• Internet of things (IoT) devices are supported.
• AP305C/CX supports Client Bridge and Wired Mesh
Network extension:
◦ When Client Bridge is configured on a single interface
AP, the single interface is used as the client port, not as
an uplink, and you will not see the GE2 Port Function.
◦ When a single interface AP is configured as a Mesh non-
root AP, the single interface is used as a client port, not
as an uplink.
◦ When a single interface AP is configured as a Mesh root,
the single interface is used as an uplink, not as a client
port.
• AP310i/e
• AP310i-1
• AP360i/e
• One dual-band 2.4GHz/5GHz radio and one 5GHz radio.
◦ Mode 1 — 2.4GHz service radio and 5GHz service radio
◦ Mode 2 — 2.4/5GHz dual-band Sensor and 5GHz service
radio
Access Points List Monitor
70 Extreme Campus Controller User Guide for version 5.46.03










