Consolidated “e” Series Hardware Installation Guide Extreme Networks, Inc. 3585 Monroe Street Santa Clara, California 95051 (888) 257-3000 http://www.extremenetworks.
Alpine, Altitude, BlackDiamond, EPICenter, Ethernet Everywhere, Extreme Ethernet Everywhere, Extreme Networks, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, GlobalPx Content Director, the Go Purple Extreme Solution Partners Logo, ServiceWatch, Summit, the Summit7i Logo, and the Color Purple, among others, are trademarks or registered trademarks of Extreme Networks, Inc. or its subsidiaries in the United States and other countries.
Contents Preface Part 1 Chapter 1 Chapter 2 Introduction 7 Conventions 8 Related Publications 8 About This Guide How To Use This Guide 9 9 Preparing for Installation Overview of the “e” Series of Switches Summit “e” Series and Models Summit 200 Features Summit 300 Features Summit 400 Features 13 13 15 16 Port Connections 18 Following Safety Information 18 Software Images 19 Full-Duplex Support 19 Site Preparation Planning Your Site Step 1: Meeting Site Requirements Step 2: Evaluating a
Rack Specifications and Recommendations Part 2 Chapter 3 Chapter 4 4 25 Evaluating and Meeting Cable Requirements Cabling Standards Cable Labeling and Record Keeping Installing Cable 27 27 28 28 Evaluating and Meeting Mini-GBIC Requirements Mini-GBIC Types and Specifications Long Range Mini-GBIC System Budgets RJ-45 Connector Jackets Radio Frequency Interference Making Network Interface Cable Connections 31 31 32 33 34 34 Meeting Power Requirements Power Supply Requirements AC Power Cable Requireme
Console Port Port Connections Summit 300 Automatic Failover Summit 300-48 Rear View Load Sharing Power Supplies Chapter 5 Part 3 Chapter 6 Part 4 Chapter 7 53 53 53 54 55 Summit 400-48t Switch Overview Summit 400-48t Switch Summit 400 Front View Summit 400 Rear View Summit 400 Switch LEDs 57 57 58 59 Port Connections Uplink Redundancy 61 61 Switch Installation “e” Switch Installation Installing the Switch Rack Mounting Removing the Switch from a Rack Free-Standing Desktop Mounting of Multiple Switc
Internal Power Supply Technical Specifications LED Visual Indicators Environmental and Safety Specifications Chapter 8 Summit 400-48t Optional Features Installing Optional Features Installing the Summit XEN Card Installing the External Power System Rack Mounting the EPS-T Adding a second EPS-160 to the EPS-T Removing an EPS-160 from the EPS-T Part 5 Appendix A 89 89 91 92 94 95 Appendixes Safety Information Important Safety Information Power Power Cable Optical Safety Lithium Battery Appendix B 84 84
Preface This preface provides an overview of this guide, describes guide conventions, and lists other publications that might be useful. NOTE To ensure proper operation of your Extreme Networks equipment, read this guide before you install any Extreme Networks equipment. Introduction This guide provides the required information to install an Extreme Networks® Summit™ switch. It also contains information about site location, switch functionality, and switch operation.
Preface Conventions Table 1 and Table 2 list conventions used throughout this guide. Table 1: Notice icons Icon Notice Type Alerts you to... Note Important features or instructions. Caution Risk of personal injury, system damage, or loss of data. Warning Risk of severe personal injury. Table 2: Text conventions Convention Description Screen displays This typeface represents information as it appears on the screen, or command syntax.
About This Guide Documentation for Extreme Networks products is available from the Extreme Networks website at the following location: http://www.extremenetworks.
Preface Switch-Specific Information For switch-specific information, be sure to read the applicable model-specific chapter. For example, if you have a Summit 400-48t switch and you need to set up a combination port, “Uplink Redundancy” on page 61 for specific details for cabling combination ports. Common Information For items applicable to any Extreme Networks switch, make sure you read the appropriate chapter.
Part 1 Preparing for Installation
1 Overview of the “e” Series of Switches This chapter describes: • Summit “e” Series and Models on page 13 • Port Connections on page 18 • Following Safety Information on page 18 on page 18 • Software Images on page 19 • Full-Duplex Support on page 19 Summit “e” Series and Models This installation manual supports the Summit models that comprise the “e” series: • The Summit 200 models: — Summit 200-24 switch — Summit 200-48 switch • The Summit 300 Power over Ethernet (PoE) models: — Summit 300-24 switch —
Overview of the “e” Series of Switches • 24 autosensing 10BASE-T/100BASE-TX ports using RJ-45 connectors • Two 10/100/1000BASE-T Gigabit Ethernet uplink ports using RJ-45 connectors • Two optical ports that allow Gigabit Ethernet uplink connections through Extreme 1000BASE-SX, 1000BASE-LX, or 1000BASE-ZX Small Form Factor pluggable (SFP) Gigabit Interface Connectors (GBICs)—also known as mini-GBICs—using LC optical fiber connectors.
Summit “e” Series and Models • Simple Network Management Protocol (SNMP) support • Remote Monitoring (RMON) • Traffic mirroring for ports Summit 300 Features This section summarizes the hardware and software features of the Summit 300. See “Summit 300 Switch Overview” on page 47 for details of the front panel, rear panel, and LEDs.
Overview of the “e” Series of Switches • Wire-speed IP multicast routing support • Diffserv support • Access-policy support for routing protocols • Access list support for packet filtering • Access list support for rate-limiting • IGMP snooping to control IP multicast traffic • Protocol Independent Multicast-Sparse Mode (PIM-SM) • Load sharing on multiple ports • Dynamic load sharing on multiple ports • RADIUS client and per-command authentication support • TACACS+ support • Console command line interface
Summit “e” Series and Models Software Features The software features of the Summit 400-48t include: • Virtual local area networks (VLANs) including support for IEEE 802.1Q and IEEE 802.1p • VLAN aggregation • Spanning Tree Protocol (STP) (IEEE 802.1D) • Rapid Spanning Tree Protocol (IEEE 802.1W) • Quality of Service (QoS) including support for IEEE 802.
Overview of the “e” Series of Switches Port Connections Extreme “e” switches use a combination of the following types of ports: • Small Form Factor Pluggable (SFP) Gigabit Interface Connectors (GBICs), also known as mini-GBICs: — 1000BASE-SX ports (850 nm optical window) using LC connectors — 1000BASE-LX ports (1310 nm optical window) using LC connectors — 1000BASE-ZX ports (1550 nm optical window) using LC connectors • 10/100/1000BASE-T Gigabit Ethernet ports using RJ-45 connectors • 10BASE-T/100BASE-TX p
Software Images Software Images When you receive a new Extreme Networks switch, be aware that an the ExtremeWare® software image and a BootROM image has been pre installed at the factory. To verify the software image you are running on your switch, use the show version command. The show version command displays the hardware and software versions currently running on the switch.
Overview of the “e” Series of Switches 20 Consolidated "e" Series Hardware Installation Guide
2 Site Preparation This chapter describes how to prepare your site for installing Extreme Networks equipment. It contains information on environmental and cabling requirements, power requirements, and building and electrical code organizations.
Site Preparation Planning Your Site To install your equipment successfully, you should plan your site carefully.
Meeting Site Requirements Building and Electrical Codes Building and electrical codes vary depending on your location. Comply with all code specifications when planning your site and installing cable. The following sections are provided as a resource to obtain additional information. Three major building codes are: • Uniform Building Code—produced by the International Conference of Building Officials (ICBO); 5360 South Workman Mill Road; Whittier, California 90601 USA. www.icbo.
Site Preparation Table 2: AC power requirements (continued) Country Requirements United Kingdom 10 A service receptacle, BS 1363 for 110/220 VAC power supplies. International 10 A service receptacle, CEE 7/7 for 110/220 VAC power supplies. Australia 10 A service receptacle, AS 3112 for 110/220 VAC power supplies. Japan 15 A service receptacle, JIS 8303 for 110/220 VAC power supplies. • Use a vinyl floor covering in your wiring closet.
Meeting Site Requirements The “e” series of switches require 3 inches (7.62 cm) on both the left and right sides of the switch (5 inches (12.7 cm) recommended) for proper airflow. The airflow of the “e” series of switches moves from the left side of the switch to the right side of the switch, or from the right side of the switch to the left side of the switch depending on the model. Humidity. Operating humidity should be kept between 10 and 95% relative humidity (noncondensing).
Site Preparation NOTE Because building codes vary worldwide, Extreme Networks strongly recommends that you consult an electrical contractor to ensure proper equipment grounding is in place for your specific installation. • Ground DC power supplies to earth ground by using the grounding terminals provided. Space Requirements for the Rack Provide enough space in front of and behind the switch so that you can service it easily.
Evaluating and Meeting Cable Requirements Figure 1: Properly secured rack (SPG_007 redraw with e series in the rack) Secure to floor with 3/8 inch lag screws or bolts SPG_007 Brace open distribution racks if the channel thickness is less than 1/4 inch (6.4 mm). Evaluating and Meeting Cable Requirements This section addresses requirements for the that cable you should use when installing your network equipment.
Site Preparation Cable Labeling and Record Keeping A reliable cable labeling system is essential when planning and installing a network. Maintaining accurate records helps you to: • Relocate devices easily. • Make changes quickly. • Isolate faults in the distribution system. • Locate the opposite end of any cable. • Know the types of network devices that your cabling infrastructure can support.
Evaluating and Meeting Cable Requirements NOTE Unshielded twisted pair (UTP) cable can build up ESD charges when being pulled into a new installation. Before installing category 5 UTP cables, discharge ESD from the cable by plugging it into a port on a switch or any network device that is not powered on.
Site Preparation NOTE Kinks and sharp bends can destroy or impair the cable’s ability to convey light pulses accurately from one end of the cable to the other. Use care in dressing the optical-fiber cables: provide satisfactory strain relief to support the cable and maintain an adequate bend radius at all cable turns, particularly where the cable connects to the I/O module. Figure 3: Bend radius for fiber optic cable Minimum 2 in. (5.
Evaluating and Meeting Mini-GBIC Requirements Evaluating and Meeting Mini-GBIC Requirements All “e” series switches support the small form pluggable (SFP) GBIC, also known as the mini-GBIC. The switches identify the type of mini-GBIC that is installed and verifies that the mini-GBIC is an Extreme Networks-certified mini-GBIC.
Site Preparation Table 5: LX mini-GBIC specifications (continued) Parameter Minimum Typical Maximum Receiver Optical input power sensitivity -23 dBm Optical input power maximum Operating wavelength -3 dBm 1270 nm 1355 nm General Total system budget 13.5 dB Total optical system budget for the LX mini-GBIC is 13.5 dB. Measure cable plant losses with a 1310 nm light source and verify this to be within budget.
Evaluating and Meeting Mini-GBIC Requirements loses induced by cable splices, connectors, and operating margin. Table 7 lists the minimum attenuations that are required by each long range mini-GBIC to prevent saturation of the receiver.
Site Preparation Radio Frequency Interference If you use unshielded twisted pair (UTP) cabling in an installation, take precautions to avoid radio frequency (RF) interference. RF interference can cause degradation of signal quality, and, in an Ethernet network environment, can cause excessive collisions, loss of link status, or other physical layer problems that can lead to poor performance or loss of communication.
Meeting Power Requirements • AC Power Cable Requirements • Uninterruptable Power Supply Requirements For more information about the power specifications of the Extreme Networks family of switches, see Appendix B, “e” Series Technical Specifications. Power Supply Requirements Adhere to the following requirements in order to operate your Extreme Networks equipment safely: • Ensure that your equipment is placed in an area that accommodates the power consumption and component heat dissipation specifications.
Site Preparation NOTE When using dual power supplies, make sure that each AC power supply attaches to an independent power source. Replacing the Power Cable If the power cable plug is unsuitable and must be replaced, connect the power supply wires for the switch according to the following scheme: • Brown wire to the Live (Line) plug terminal, which might be marked with the letter “L” or colored red. • Blue wire to the Neutral plug terminal, which might be marked with the letter “N” or colored black.
Applicable Industry Standards NOTE Extreme Networks recommends that you use a UPS that provides online protection. Calculating Amperage Requirements To determine the size of UPS that you need, use the following procedure: 1 To find VA (Volt-Amps), locate the voltage and amperage requirements for each piece of equipment. These numbers are usually located on a sticker on the back or bottom of your equipment.
Site Preparation 38 Consolidated "e" Series Hardware Installation Guide
Part 2 Switch Overview
3 Summit 200 Series Switch Overview This chapter describes the features and functionality of the Summit 200 series switches: • Summit 200 Series Switches on page 41 • See “Evaluating and Meeting Mini-GBIC Requirements” on page 31 for mini-GBIC types and distances.
Summit 200 Series Switch Overview Figure 5: Summit 200-24 switch front view 10/100 Mbps ports Mini-GBIC port status LEDs 1000-baseT ports Unit stacking Console port ID LED Mini-GBIC ports LC24001A Figure 6: Summit 200-48 switch front view 10/100 Mbps ports Mini-GBIC ports Console port 1000-baseT ports LC48001 NOTE See “Evaluating and Meeting Mini-GBIC Requirements” on page 31 for information about supported GBIC types.
Summit 200 Series Switches Power Socket The Summit 200 switch automatically adjusts to the supply voltage. The power supply operates down to 90 V. Serial Number Use this serial number for fault-reporting purposes. MAC Address This label shows the unique Ethernet MAC address assigned to this device. NOTE The Summit 200 switch certification and safety label is located on the bottom of the switch. NOTE See “Evaluating and Meeting Mini-GBIC Requirements” on page 31 for mini-GBIC types and distances.
Summit 200 Series Switch Overview Table 9: Summit 200 switch LED behavior (continued) Fiber Port Status LEDs (Ports 25 and 26 or Ports 49 and 50) Color Indicates Green Link is present; port is enabled. Green blinking Link is present, port is enabled, and there is activity on the port. Off Link is not present, port is disabled, or non-supported GBIC is installed on the port.
Port Connections On the Summit 200-24, ports 25 and 26 are the Gigabit Ethernet ports that have the redundant PHY interfaces. On the Summit 200-48, it is ports 49 and 50. Each port has one mini-GBIC and 1000BASE-T connection. To set up a redundant link on either port 25 or on port 49, connect the active fibre and 1000BASE-T links to both the RJ-45 and mini-GBIC interfaces of that port.
Summit 200 Series Switch Overview Full-Duplex Both models of the Summit 200 provide full-duplex support for all ports. Full-duplex allows frames to be transmitted and received simultaneously and, in effect, doubles the bandwidth available on a link. All 10/100 Mbps ports on the Summit 200 switch autonegotiate for half- or full-duplex operation.
4 Summit 300 Switch Overview This chapter describes the features and functionality of the Summit 300 series switch. It contains the following sections: • Summit 300 Series Switches on page 47 • Summit 300-24 Switch on page 47 • Summit 300-48 Switch on page 51 Summit 300 Series Switches The Summit 300 series switches include the following switch models: • Summit 300-24 switch • Summit 300-48 switch Summit 300-24 Switch The Summit 300-24 supports wireless and Power over Ethernet (PoE) networks.
Summit 300 Switch Overview Figure 9: Summit 300-24 switch front view 10/100 Mbps ports Management LED Fan LED PSU LEDs Console port Mini-GBIC port status LEDs 10/100/1000-baseT ports Mini-GBIC/ 1000-baseX ports RVN24001A Summit 300-24 Switch LEDs The light emitting diode (LED) behavior on the Summit 300-24 is described in Table 10. Table 10: Summit 300-24 switch LED behavior (continued) Unit Status LED (MGMT LED) Color Indicates Green, solid The Summit switch is operating normally.
Summit 300-48 Switch Table 10: Summit 300-24 switch LED behavior (continued) Port Status LEDs (Ports 1-24) Color Indicates Green, solid Link is present and port is enabled; non-powered device. Green, fast blinking Port is enabled; link is up, device non-powered and activity on the port. Amber, solid Link is present and port is enabled; device powered. Amber, slow blinking Link is down or port is disabled; device powered.
Summit 300 Switch Overview Summit 300-24 RearSummit 300-48 switch View Figure 10 shows the rear view of the Summit 300-24 switch.
Summit 300-48 Switch Redundant Power Supply The Summit 300-24 supports Power over Ethernet (PoE) as defined by the IEEE 802.3af specification. PoE is an effective method of supplying 48 VDC power to certain types of powered devices (PDs) by way of Category 5 or Category 3 twisted pair Ethernet cables. Supported devices include the Altitude 300 wireless port, IP telephones, laptop computers, web cameras, or other devices.
Summit 300 Switch Overview NOTE See “Evaluating and Meeting Mini-GBIC Requirements” on page 31 for information about supported mini-GBIC types and distances. LED Behavior The light emitting diode (LED) behavior for the Summit 300-48 is shown in Figure 11. Table 11: Summit 300-48 switch LED behavior Unit Status LED (MGMT LED) Color Indicates Blinking Green The Summit switch is operating normally. Solid Amber The Summit has failed its POST. Off No power.
Summit 300-48 Switch Table 11: Summit 300-48 switch LED behavior 10/100 Mbps Port Status LEDs Color Indicates Green, solid Link is present and port is enabled; non-powered device. Green, fast blinking Port is enabled; link is up, device non-powered and activity on the port. Amber, solid Link is present and port is enabled; device powered. Amber, slow blinking Link is down or port is disabled; device powered.
Summit 300 Switch Overview 1000BASE-T connection for each port. On the Summit 300-48 it is ports 1:49-1:52 that are dual-mode redundant ports. Only one media type (fiber or copper) can be active at the same time on those ports. The two fiber ports and the first two of the 10/100/1000BASE-T ports on the Summit 300-24 and the four fiber ports and the first four of the 10/100/1000BASE-T ports are designed as combination ports for uplink redundancy.
Summit 300-48 Switch Power Socket The Summit 300-48 switch automatically adjusts to the supply voltage. The power supply operates down to 90 V. Power Switch The Summit 300-48 switch has a power switch. Do not turn on power to the switch until instructed in the installation procedures. NOTE Summit 300-48 switchThe Summit 300-48 switch certification and safety label, and the serial number and MAC address labels are located on the bottom of the switch.
Summit 300 Switch Overview 50 Consolidated "e" Series Hardware Installation Guide
5 Summit 400-48t Switch Overview This chapter describes the features and functionality of the Summit 400-48t. • Summit 400-48t Switch on page 57 • Summit 400 Switch LEDs on page 59 • Port Connections on page 61 Summit 400-48t Switch The Summit 400-48t switch is a compact enclosure (see Figure 14) one rack unit in height (1.73 inches or 44.0 mm) that provides 48 autosensing 10/100/1000BASE-T ports using RJ-45 connectors.
Summit 400-48t Switch Overview LEDs—For a description of the LEDs and their behavior, see “Summit 400 Switch LEDs” on page 59. Fiber uplink ports—For more information about these four ports, see “Evaluating and Meeting Mini-GBIC Requirements” on page 31. 10/100/1000BASE-T ports—For more information about these 48 ports, see “Port Connections” on page 61. Console Port—Use the console port (9-pin, “D” type connector) to attach a terminal and access the CLI through a serial connection.
Summit 400-48t Switch These ports are currently not supported but are reserved for future software features. • Vents for the internal power supply fan. • The connector for the optional Extreme External Power Supply System. For further information about this feature, see “Installing Optional Features” on page 89. • AC Power Socket The Summit 400-48t switch automatically adjusts to the supply voltage. The power supply operates from 100 VAC to 240 VAC.
Summit 400-48t Switch Overview Table 12: Summit 400 switch LED behavior Unit Status LED (MGMT LED) Color Indicates Green, slow blinking The Summit switch is operating normally. Green, fast blinking The Summit switch POST is in progress. Green, solid POST passed; ExtremeWare is booting. Amber, blinking The Summit switch has failed its POST or an overheat condition is detected. Off The Summit switch has no power. Color Indicates Green solid All fans are operating normally.
Port Connections Port Connections The Summit 400-48t switch has 48 copper 10/100/1000BASE-T ports using RJ-45 connectors for communicating with end stations and other devices over 10/100/1000 Mbps Ethernet. The switch also has four fiber ports that allow Gigabit Ethernet uplink connections through Extreme 1000BASE-SX, 1000BASE-LX, or 1000BASE-SX SFP mini-GBICs using LC connectors.
Summit 400-48t Switch Overview NOTE To support automatic failover between the fiber and copper ports, you must use an Extreme mini-GBIC connector.
Part 3 Switch Installation
6 “e” Switch Installation You can mount an “e” series switch in a rack or place it free-standing on a tabletop.
“e” Switch Installation Rack Mounting CAUTION Do not use the rack mount kits to suspend the switch from under a table or desk, or to attach the switch to a wall. To rack mount the Summit 200 series switch: 1 Place the switch upright on a hard flat surface, with the front facing you. 2 Remove the existing screws from the sides of the case (retain the screws for Step 4). 3 Locate a mounting bracket over the mounting holes on one side of the unit.
Installing or Replacing a Mini-Gigabit Interface Connector (Mini-GBIC) Removing the Switch from a Rack To uninstall an “e” series switch from a rack, you need a # 1 Phillips screwdriver. To remove the Summit switch from a standard 19-inch (48.26 cm) rack: 1 Remove power from the switch. • On the Summit 300-48, turn the power switch on the rear panel to the off position. • Unplug the power cable(s) from the from the wall outlet(s) and then from the switch.
“e” Switch Installation In addition to the previously described tasks, Extreme Networks recommends the following when installing or replacing mini-GBICs on an active network: • Use the same type of mini-GBIC at each end of the link. • Connect one end of the link to the Tx port. Without an attenuator, measure the total loss from the Tx port to the other side of the link. Once you complete all of the described tasks, you are ready to install or replace a mini-GBIC.
Connecting Equipment to the Console Port Inserting a Mini-GBIC To insert a mini-GBIC connector: 1 Holding the mini-GBIC by its sides, insert the mini-GBIC into the SFP receptacle on the switch. Mini-GBICs can be installed in: • Ports 25 and 26 on the Summit 200 and Summit 300-24 switches. • Ports 49 through 52 on the Summit 300-48 switch. • Ports 1X to 4X on the Summit 400-48t.
“e” Switch Installation Figure 19 shows the pin-outs for a 9-pin to RS-232 25-pin null-modem cable. Figure 19: Null-modem cable pin-outs Summit PC/Terminal Cable connector: 9-pin female Cable connector: 25-pin male/female Screen Shell TxD 3 RxD 2 Ground 5 RTS 7 CTS 8 DSR 6 DCD 1 DTR 4 1 3 2 7 4 20 5 6 8 Screen RxD TxD Ground RTS DTR CTS DSR DCD ser_sum1 Figure 20 shows the pin-outs for a 9-pin to 9-pin PC-AT null-modem serial cable.
Logging In for the First Time NOTE For more information on the LEDs, see Chapter 1. Logging In for the First Time After the switch completes the POST, it is operational. Once operational, you can log in to the switch and configure an IP address for the default VLAN (named default). To configure the IP settings manually, follow these steps: 1 Connect a terminal or workstation running terminal-emulation software to the console port.
“e” Switch Installation 72 Consolidated "e" Series Hardware Installation Guide
Part 4 Accessory Installation
7 Summit 300 Optional Features This chapter describes how to install optional features on the Summit 300 family of switches. You can order the following features from your Extreme sales representative: • External Power Supply (45019) on page 75 • Internal 600 Watt Power Supply (15412) on page 79 External Power Supply (45019) The Extreme Networks External Power Supply 45019 (EPS-LD) provides additional power to the Summit 300-24.
Summit 300 Optional Features Table 14 lists the electrical specifications for each EPS-LD unit. Table 14: EPS-LD power supply specifications Ratings Nominal Operating Voltage 115 VAC or 230 VAC Input Voltage Range 100 VAC to 240 VAC AC Line Frequency 50 Hz to 60 Hz Maximum Input Current Rating 10A at 115 VAC, 5A at 230 VAC Maximum Inrush Current 30A at 115 VAC, 60A at 230 VAC Output -50 VDC, 7.5 A max, 375 Watts; 12 VDC, 7.
External Power Supply (45019) 1 Place the EPS-LD unit upright on a hard flat surface, with the side you want to face to the front of the switch toward you. 2 Remove the mounting bracket kit (including screws) from the packaging. 3 Locate a mounting bracket over the mounting holes on one side of the unit. 4 Insert the screws, as shown in Figure 21, and fully tighten the screws with a #1 Phillips screwdriver.
Summit 300 Optional Features Figure 22: EPS-LD cable with key Collin's ES4K027 XM_055 Figure 23: Cable connector for connecting an EPS-LD unit to a switch Keyed end of redundant power cable Slot for key EPS-LD To AC Extreme switch Redundant power cable To AC 3 Connect the AC input power cable to the AC connector on the EPS-LD unit. Collin's CAUTION The EPS-LD unit does not have a switch for turning the unit on and off.
Internal 600 Watt Power Supply (15412) Removing an EPS-LD unit To remove an EPS-LD unit: 1 Disconnect the AC power by removing the plug from the wall. 2 Disconnect the AC power cord from the EPS-LD unit. 3 Remove the cable that connects to the Extreme switch from the EPS-LD unit. 4 Loosen the thumbscrews on the front of the EPS-LD mounting racks. 5 Slide EPS-LD unit out of rack.
Summit 300 Optional Features • Internal Power Supply Technical Specifications on page 84 Removing and Installing Summit 300-48 Power Supplies The Summit 300-48 comes with a minimum of one power supply pre-installed at the factory. Follow the instructions in this section for removing and installing power supplies. Switches with one power supply have a metal cover plate in place of the second supply.
Internal 600 Watt Power Supply (15412) Figure 25: Removing the Summit 300-48 power supply LB48020A 5 If you are not going to install a replacement power supply, cover the power supply bay with the blank cover plate that was originally supplied with the switch. Installing an Internal Power Supply To install an internal Summit 300-48 power supply: 1 Confirm that the power supply switch on the power supply to be installed is set to the OFF position.
Summit 300 Optional Features Installing and Removing Power Cable Retaining Brackets The power cable for the Summit 300-48 power supply can be attached to the supply using power cable retaining brackets. The retaining brackets make it less likely that a power supply cable will be inadvertently knocked loose from a power supply. Installing the Power Cable Retaining Bracket To install a power cable retaining bracket: 1 Turn off the power supply by setting the power switch to the OFF position.
Internal 600 Watt Power Supply (15412) Figure 27: Attaching the retaining bracket using spacers Spacers Bracket screws LB48024 4 Connect the power cable to the switch CAUTION Do not connect the power cable to the power source at this time. 5 For power supplies with permanently attached standoffs, attach the retaining bracket to the power supply using the bracket screws, as shown in Figure 26.
Summit 300 Optional Features Figure 28: Attaching two retaining brackets Retaining bracket screw Retaining bracket screw LB48022A Removing the Power Cable Retaining Bracket To remove a power cable retaining bracket from a power cable: 1 Turn off the power supply by setting the power switch to the OFF position. 2 Disconnect the power cable from the power source. 3 Loosen the retaining bracket screw. See Figure 26 and Figure 28 for the location of the screws.
Internal 600 Watt Power Supply (15412) indicates the condition of the output DC power supplied by the power supply to the switch. When the output power is satisfactory the OUT LED is green, otherwise it is off.
Summit 300 Optional Features Environmental and Safety Specifications Table 18: Summit 300-48 power supply specifications Safety Agency Certifications and Standards North American Safety of ITE • UL60950 3rd Edition, Listed Device • CSA 22.
Internal 600 Watt Power Supply (15412) Power Supply Specifications Nominal Input Voltage 100/115/200/208/230 VAC Input Voltage Range 85 VAC to 264 VAC AC Line Frequency 47 Hz to 63 Hz Power Supply Input Connection IEC60320 C13 with minimum 18 AWG stranded copper wire Maximum Input Current 9.5 A @ 90 VAC, 6.95 A @ 115 VAC, 3.
Summit 300 Optional Features 88 Consolidated "e" Series Hardware Installation Guide
8 Summit 400-48t Optional Features This chapter describes how to install optional features on “e” series switches.. • Installing Optional Features on page 89 Installing Optional Features Extreme Networks offers two hardware products that extend the capabilities of the Summit 400-48t. The Summit XEN Card is an additional card that adds one or two 10 Gigabit uplink modules through the back of the Summit 400-48t.
Summit 400-48t Optional Features 4 Place the Summit XEN Card into the drawer. 5 Carefully close the drawer to engage the card. Installing XENPAK Optical Transceiver Modules This section describes installing and removing the XENPAK module, a 10 Gbps optical transceiver. Both the LR XENPAK and the ER XENPAK appear and install the same. An example of an XENPAK module is shown in Figure 30.
Installing Optional Features 6 Secure the module to the card by turning the two captive screws clockwise until they are hand-tight. 7 Place the Summit XEN Card into the supplied drawer and carefully slide the drawer into the switch housing until the card seats and the drawer is flush with the remainder of the back panel. 8 Hand tighten the screws clockwise on the faceplate to keep the Summit XEN Card in place.
Summit 400-48t Optional Features CAUTION The Extreme External Power System must only be installed or removed by trained service personnel in accordance with the installation instructions. Before servicing this system, please read the safety information provided in. Not following these precautions can result in equipment damage or shock. Table 19 lists the specifications for each EPS-160 installed in the External Power System.
Installing Optional Features Figure 31: Fitting the mounting bracket ES4K026 5 Repeat steps 2 through 4 for the other side of the EPS-T. 6 Insert the EPS-T into a 19-inch rack. CAUTION Do not attach the AC power cord to the EPS-160 until it is properly mounted in the EPS-T (that is properly grounded) and after the redundant power supply cable is connected. 7 Connect the keyed-end of the redundant power supply cable to the EPS-160.
Summit 400-48t Optional Features Figure 33: Redundant Power Connection Slot for plug To AC Keyed end of redundant power cable Redundant power cable ES4K021A Table 20: Connection Specifications for the Redundant Connector Diagram 1 8 7 14 ES4K028 Pin Wire Label 1 NC 2 GND 3 GND 4 GND 5 GND 6 +12 V 7 +12 V 8 RS+ 9 GND 10 INT PG 11 EXT_CON 12 EXT_PG 13 +5 V 14 +12 V 8 Connect the other end of each EPS-160 power supply cable to the Extreme switch.
Installing Optional Features 1 Remove the EPS-160 from the packing material. 2 Insert the EPS-160 into the front of the EPS-T. 3 Tighten the provided thumbscrews to secure the power supply to the tray. 4 Follows steps 7 through 9 on page 93. Removing an EPS-160 from the EPS-T To remove an EPS-160 from an EPS-T: 1 Disconnect the AC by removing the plug from the wall 2 Disconnect the AC power cord from the EPS-160. 3 Remove the redundant power cable from the EPS-160.
Summit 400-48t Optional Features 96 Consolidated "e" Series Hardware Installation Guide
Part 5 Appendixes
A Safety Information Important Safety Information WARNING! Read the following safety information thoroughly before installing your Extreme Networks switch. Failure to follow this safety information can lead to personal injury or damage to the equipment. Installation, maintenance, and removal of a switch, chassis, or its components must be done by qualified service personnel only.
Safety Information • Operate the unit and attached equipment under Safety Extra Low Voltage (SELV) conditions. The “e” series of switches operate under SELV conditions according to the IEC 950 standard. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions. • Ensure that the appliance coupler (the connector to the unit and not the wall plug) has a configuration for mating with an EN60320/IEC320 appliance inlet.
Important Safety Information WARNING! Use fiber optic ports only for data communications applications that require optical fiber. Use only with the appropriate connector. When not in use, replace dust cover. Using this module in ways other than those described in this manual can result in intense heat that can cause fire, property damage, or personal injury. Mini-GBICs. Remove the LC fiber-optic connector from the mini-GBIC prior to removing the mini-GBIC from the switch.
Safety Information 102 Consolidated "e" Series Hardware Installation Guide
B “e” Series Technical Specifications This appendix describes the hardware technical specifications for “e” series of Extreme Network switches.
“e” Series Technical Specifications Country Specific Mexico NOM/NYCE (Product Safety and EMC Approval) Australia/New Zealand AS/NZS 3260 (ACA DoC, Safety of ITE) Argentina S-Mark GOST (Russia) Laser Safety North America FCC 21 CFR subpart (J) (Safety of Laser Products) CDRH Letter of Approval (US FDA Approval) Europe • EN60825-2 (European Safety of Lasers) • EN60825-1:1994+A11:1996+A2 (European Safety of Lasers Products) (Summit 300 only) Electromagnetic Compatibility North America FCC 47 CFR Par
Summit 200 Series Switch Specifications ACN 090 029 066 C-Tick (Australian Communication Authority) Underwriters Laboratories (USA and Canada) MIC (South Korea) BSMI, Republic of Taiwan NOM (Mexican Official Normalization, Electronic Certification and Normalization) Summit 200 Series Switch Specifications The Summit 200 series has two models, a 24 port and a 48 port model. Table 23 lists the specifications that are common to both models, while Table 23 and Table 24 give model specific information.
“e” Series Technical Specifications Table 23: Summit 200-24 Unique Specifications Physical and Environmental Heat Dissipation, Watts/BTU 24.1 W Table 24: Summit 200-48 Unique Specifications Physical and Environmental Dimensions Height: 1.75 inches (4.44 cm) Width: 17.3 inches (43.94 cm) Depth: 12.2 inches (31.00 cm) Weight Weight: 9.7 lbs (4.4 kg) Heat Dissipation, Watts/BTU 48.0 W Summit 300 Series Switch Specifications The Summit 300 series has two models, a 24 port and a 48 port model.
Summit 400 Series Switch Specifications Table 27: Summit 300-48 unique specifications Summit 300-48 switchPhysical Summit 300-48 switchSummit 300-48 switchDimensions Summit 300-48 Height: 3.5 inches (8.89 cm) Width: 17.25 inches (43.815 cm) Depth: 18.25 inches (46.355 cm) Weight (with one power supply unit): 14 lbs (6.
“e” Series Technical Specifications 108 Consolidated "e" Series Hardware Installation Guide
Index Numerics 10 Gigabit uplinks 1000BASE-LX 1000BASE-SX 1000BASE-ZX 58, 89 30 30 30 A AC power cable planning AC power requirements AC power socket Summit 200 switches Summit 300-24 switch Summit 300-48 Summit 400 AC power switch Summit 300-48 switch Summit 300-48 switch 35 23 43 50 55 59 power switch55 agency certifications airflow requirements amperage, calculating ANSI standards automatic failover setting up Summit 200-24 rules Summit 200-48 rules Summit 300 rules Summit 400-48t rules 86 24 37 37
E electrical codes, planning for electromagnetic compatibility Summit 200-24 switch Summit 300-48 power supply electrostatic discharge environmental requirements planning for Summit 200-24 switch Summit 200-48 switch Summit 400-48t switch EPS-160 EPS-T ER XENPAK External Power Supply EPS-LD External Power System I 23 104 86 29 24 105 106 107 91 91 89 75 89, 91 F fan status LED Summit 200 switches Summit 300-24 switch Summit 300-48 switch Summit 400 switch features, software fiber optic cable fiber port st
load sharing specifications uninterruptable power supply LEDs Summit 300-24 Summit 300-48 Summit 400 Summit 400 switch powered device power-off specifications Summit 200-24 switch 55 105 to 107 36 48 52 60 59 51 105 R rack mounting the switch rack specifications grounding mechanical recommendations mounting holes securing to floor space requirements radio frequency interference avoiding cable installation precautions and planning recording cable locations redundant Gigabit uplink port Summit 200-24 rules
uplink redundancy setting up Summit 200-24 rules Summit 200-48 rules Summit 300 switches Summit-400 switch UPS, See uninterruptable power supply 44 45 45 54 61 W weight Summit 200-24 Summit 200-48 Summit 400 switch wiring closet airflow requirements grounding humidity planning wiring terminals 105 106 107 24 24 25 23 25 X XENPAK optical transceivers 112 89 Consolidated "e" Series Hardware Installation Guide
