Installation Guide
Table Of Contents
- Table of Contents
- Preface
- 1: AP460i/e Overview
- 2: Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options, Brackets, and Accessories
- Position the Access Point before Installation
- Install the Access Point on a Wall or Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Flat Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attaching the access point to a pole using all three KT-147407-02 bracket parts
- Attaching the access point to a pole using the pole part of the KT-147407-02 bracket
- Mounting the access point to a pole using pole part of the KT-147407-02 bracket and the KT-150173-01 extension arm
- Mounting the access point to a pole using the KT-147407-02 bracket parts and the KT-150173-01 extension arm
- Attaching the access point to a pole using the WS-MBO-POLE01 bracket and MBO-ART02 articulating mounting bracket
- 3: Powering method
- 4: GE/Console connections
- 5: Antenna configuration for external antenna model
- 6: Specifications
- 7: Regulatory Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Anatel Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
Figure 5: KT-147407-02 bracket 1-axis tilt part
Note
The flat part and the 1-axis tilt part can be used interchangeably with the access points. You
can either attach the flat part or the 1-axis tilt part first and the rest of the installation
procedure will not be aected by it.
The following hardware is required:
•
KT-147407-02 flat part
•
KT-147407-02 1-axis tilt part
•
Access point
•
Ten M6 hex-head screws
•
Two M6 screws to attach the KT-147407-02 flat part to the access point
•
Four M6 screws to attach the KT-147407-02 1-axis tilt part to a flat surface
•
Four M6 screws to attach the KT-147407-02 flat part to the 1-axis tilt part
1 Attach the KT-147407-02 flat part to the access point using two M6 hex-head screws.
2 Using the 1-axis tilt part as a template, mark and drill four holes on a wall or a flat surface.
3 Attach the 1-axis tilt part to a wall or a flat surface using four M6 head-size screws.
4 Align the KT-147407-02 flat part bracket inside the 1-axis tilt part, and attach it using four M6 screws.
5 Tilt the access point to a desired angle and tighten the four M6 screws to a torque of 45 in-lbs.
The tilt bracket can be adjusted from +15 degrees to -15 degrees of tilt.
Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-
axis Tilt Part, and the KT- 150173-01 Extension Arm
In installations that require an extension arm, the access point is attached to a flat surface using the
KT-147407-02 bracket parts and the KT-150173-01 extension arm.
Install the Access Point
ExtremeMobility AP460i/e Outdoor Access Points 15