ExtremeMobility AP460i/e Outdoor Access Points Installation Guide 9036418-00 Rev AA Published November 2019
Copyright © 2019 Extreme Networks, Inc. All rights reserved. Legal Notice Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice.
Table of Contents Preface................................................................................................................................................................................................ 4 Conventions............................................................................................................................................................................. 4 Providing Feedback to Us.................................................................................
Preface This section discusses the conventions used in this guide, ways to provide feedback, additional help, and other Extreme Networks® publications. Conventions This section discusses the conventions used in this guide. Text Conventions The following tables list text conventions that are used throughout this guide. Table 1: Notice Icons Icon New! Notice Type Alerts you to... General Notice Helpful tips and notices for using the product. Note Important features or instructions.
Providing Feedback to Us Quality is our first concern at Extreme Networks, and we have made every effort to ensure the accuracy and completeness of this document. We are always striving to improve our documentation and help you work better, so we want to hear from you! We welcome all feedback but especially want to know about: • Content errors or confusing or conflicting information. • Ideas for improvements to our documentation so you can find the information you need faster.
1 Go to www.extremenetworks.com/support/service-notification-form. 2 Complete the form with your information (all fields are required). 3 Select the products for which you would like to receive notifications. Note You can modify your product selections or unsubscribe at any time. 4 Click Submit. Documentation and Training To find Extreme Networks product guides, visit our documentation pages at: Current Product Documentation www.extremenetworks.
1 AP460i/e Overview AP460i/e Features LED Indicators Access Point Purchase Order Information The AP460i/e access points are outdoor model enterprise class 802.11ax access points. The “i” in AP460i indicates that the access point comes with internal antennas and the “e” in AP460e indicates that it comes with external antenna connectors. The access points feature a dual-band radio, two bandlocked radios, eight WiFi internal or external antennas, and one Bluetooth Low Energy (BLE) antenna.
AP460i/e Overview Figure 1: AP460i access point front view Callout Description 1 Console port and reset button cap 2 GE2 3 GE1-PoE 4 Gore vent ExtremeMobility AP460i/e Outdoor Access Points 8
AP460i/e Overview Figure 2: AP460e access point front view Callout Description 1 Console port and reset button cap 2 GE2 3 GE1-PoE 4 Gore vent Note On the AP460e access point, the sensor and the BLE antennas come with dust caps on them. Do not remove the dust cap until you need to install the antennas. For information on the AP460e antenna connectors, see antenna configuration for external antenna model access point.
AP460i/e Overview Figure 3: LEDs Note The LED icons and the status on AP460i and AP460e are the same. Table 3: AP460i/e LED status LED icon LED color Description Status Green Normal operational status Amber Non-operational status Amber 100Mbps Green 1000Mbps Purple 2.5G Amber 100Mbps Green 1000Mbps Radio 1 Green 2.
AP460i/e Overview Access Point Purchase Order Information The AP460i and AP460e access points must be ordered separately, the ordering details of which are presented in the tables below: Table 4: AP460i purchase order information Part number Description AP460i-FCC Dual/Tri radio 802.11ax/ac/abgn, 4x4:4 MIMO outdoor internal antenna access point. Domain: US, Puerto Rico, and Colombia AP460i-WR Dual/Tri Radio 802.11ax/ac/abgn, 4x4:4 MIMO outdoor internal antenna access point.
2 Install the Access Point AP460i/e Box Contents Access Point Mounting Options, Brackets, and Accessories Position the Access Point before Installation Install the Access Point on a Wall or Flat Surface Install the Access Point on a Pole The AP460i/e access points can be installed to a flat surface such as a wall or to a pole. Refer to the purchase order information to know more about selecting the right access point for your installation needs.
Install the Access Point Table 7: AP460i/e mounting brackets and accessories usage Mounting bracket and part Wall install number Pole install Notes KT-147407-02; bracket; comes with three parts: • Flat part • 1-axis tilt part • Pole part Yes Yes For attaching to a wall or a flat surface, use the bracket part that has two holes on the surface of the metal portion; also called the flat part.
Install the Access Point Position the Access Point before Installation When you install the access point, the gore vent must be on the side closest to the ground, and not above the plastic cover. You must provide a 3-inch drip loop on all cables. Note The sensor and BLE antennas come with dust cap on them. Do not remove the dust cap until you need to install the antennas.
Install the Access Point Figure 5: KT-147407-02 bracket 1-axis tilt part Note The flat part and the 1-axis tilt part can be used interchangeably with the access points. You can either attach the flat part or the 1-axis tilt part first and the rest of the installation procedure will not be affected by it.
Install the Access Point Figure 6: KT-150173-01 extension arm The following hardware is required for installation: • KT-147407-02 flat part • KT-147407-02 1-axis tilt part • KT-150173-01 extension arm • Access point • Ten M6 hex-head screws • Two M6 hex-head screws to attach the KT-147407-02 flat part to the access point • Four M6 hex-head screws to attach the 1-axis tilt part to the flat bracket • Four M6 hex-head screws to attach the KT-150173-01 extension arm to a flat surface • Two hex-head M12 stainle
Install the Access Point Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm For installation for which you don't want to use the KT-147407-02 brackets, you can attach the access point to a flat surface using just the KT-150173-01 extension arm.
Install the Access Point 1 Using the MBO-ART02 shorter bracket end as a template, mark and drill four holes on the wall. Figure 7: MBO-ART02 articulating mounting bracket template for wall attachment holes 2 Attach the MBO-ART02 articulating mounting bracket to the access point using two M6 hex-head screws. 3 Align the MBO-ART02 articulating mounting bracket holes against the wall attachment holes and attach the bracket using four M6 hex-head screws.
Install the Access Point • • Stiffener plate #2; used with the AP attach assembly plate Vehicle attach assembly plate with PEMS Table 8: WS-MBV-VMM Vehicle Bracket (#32216) box contents Item Quantity VMM vehicle attach assembly Vehicle attach plate with PEMS VMM AP attach assembly AP attach flat plate with stiffener #1 and stiffener #2 Philips Pan Head M4 (15mm) screws Four screws to attach the AP attach assembly plate to the access point The installer must provide the following hardware: 1 Acc
Install the Access Point 3 Align the large holes and assemble both the stiffener plates inside the AP attach assembly plate. Figure 9: VMM access point attach assembly plate stiffener #1 and stiffener #2 4 Attach four M4 or M6 screws to stiffener plate #2 and align the AP's threaded holes to the AP attach assembly plate. The screw head goes inside the small bracket with the bent sides. Note The bracket comes with four M4 screws. 5 Tighten the screws to 10 in-lbs.
Install the Access Point • • • KT-150173-01 extension arm with the KT-147407-02 pole part KT-150173-01 extension arm with KT-147407-02 bracket parts WS-MBO-POLE01 bracket with the MBO-ART02 articulating mounting bracket Figure 10: KT-147407-02 pole part Note The pole install options are applicable to both internal and external antenna model outdoor access points.
Install the Access Point Attaching the access point to a pole using all three KT-147407-02 bracket parts Attach the access point to a pole using all three bracket parts that comes with the KT-147407-02 bracket.
Install the Access Point Figure 12: Large bracket holes on the pole part of the KT-147407-02 bracket Label Description A Large bracket holes used for attaching the M12 screws on the pole part of the KT-147407-02 bracket 3 Fasten the M12 screws using two M12 hex nuts. 4 Insert the 0.5" stainless-steel cable clamp through the long slots on the sides of pole bracket.
Install the Access Point Label Description A Long slots on the sides of the pole part of the KT-1474017-02 bracket. These slots are used to insert the 0.5" stainless-steel cable clamps. 5 Attach the pole bracket to a pole by positioning the cable clamps on the pole bracket around a pole. 6 Insert the ends of the cable clamps around the pole and tighten the clamp screws to a torque of 11 in-lbs.
Install the Access Point Label Description A Semi-circular cuts on the pole part of the KT-147407-02 bracket, used for attaching the M6 hexhead screws. 2 Insert the 0.5" stainless-steel cable clamp through the long slots on the sides of pole bracket. 3 Attach the pole bracket to a pole by positioning the cable clamps on the pole bracket around a pole. 4 Insert the ends of the cable clamps around the pole and tighten the clamp screws to a torque of 11 in-lbs.
Install the Access Point • • Two 0.5" wide stainless-steel cable clamps Access point To install the access point to a pole: 1 Attach the flat part of the KT-147407-02 bracket to the access point. For instruction on how to attach the bracket parts, see attaching the flat part and the 1-axis tilt part of the KT-147407-02 bracket to the access point. 2 Align the circlular holes on one end of the KT-150173-01 extension arm against the large holes on the 1-axis tilt bracket.
Install the Access Point 6 Attach the pole bracket to a pole by positioning the cable clamps around a pole. 7 Insert the ends of the cable clamps around the pole and tighten the clamp screws to a torque of 11 in-lbs. Attaching the access point to a pole using the WS-MBO-POLE01 bracket and MBO-ART02 articulating mounting bracket The following hardware is required to install the access point to a pole using the WS-MBO-POLE01 bracket and the MBO-ART02 bracket.
Install the Access Point 2 Attach the WS-MBO-POLE01 bracket to the MBO-ART02 articulating mounting bracket using four M3 screws, nuts, and washers. Figure 16: The POLE01 bracket being attached to the ART02 articulating mounting bracket 3 Attach both the cable clamps to the WS-MBO-POLE01 bracket. Open the cable clamp by turning a flat bladed screwdriver counterclockwise. Then insert the nonclamp end into the pole bracket through the holes.
Install the Access Point 5 Tighten the cable clamp screw clockwise, tightening the band around the pole.
3 Powering method The AP460i and AP460e access points have one Power over Ethernet (PoE) PD converter that supplies that main powerto all the downstream. Table 9: AP460i/e powering method Power source Description PoE Power is provided through the RJ45 Ethernet ports of AP460i/e, compliant to be powered with 802.3at and 802.3bt to provide full functionality. For reduced functionality, use 802.3af.
4 GE/Console connections Installing the cable gland adapter assembly The AP460i/e access points have two GE (Ethernet) ports and a Console port. During administration and maintenance through the GE or Console, the access points must still have a power connection through an Ethernet PoE cable. For information about the location of the GE and console ports, see AP460i/e features.
GE/Console connections 1 Insert the RJ45 cable onto the sealing nut. 2 Slide the claw and seal onto the RJ45 cable. 3 Attach the main body into the GE1 or GE2 port of the access point.
GE/Console connections 4 Plug the RJ45 cable into the port. Caution Do not run the network cable through the cable conduit connector used for connecting the power cables. You must connect the network cable and power cables through separate connectors. 5 Slide the seal and the claw into the main body. 6 Secure the seal nut onto the main body. 7 Tighten the adapter assembly by hand. Tighten the cap to 5 inch lbs. Note There should still be some visible threads after you torque in the cap.
5 Antenna configuration for external antenna model There are extenal antenna connectors on AP460e access point, and it can be configured as described in the following section. Figure 19: AP460e external antenna connectors The 2.4G/5G-8 and the 2.4G/5G-7 are sensor antenna ports. Note The internal BLE is always used unless you attach an antenna to the BLE antenna connector.
Antenna configuration for external antenna model Note The BLE antenna port and the sensor antenna ports come with dust caps installed on them. Do not remove the dust caps until you need to install the antennas.
6 Specifications Product specifications Item Specification Dimensions AP460i - 7.8" x 9.2" x 2.3" (198mm x 234mm x 59mm) AP460e - 7.8" x 10.5" x 2.3" (198mm x 268mm x 59mm) Housing IP67 rated outdoor use Available mounting See Access Point Mounting Options, Brackets, and Accessories on page 12. LEDs Seven Radios Tri-radio: 2X2:2 2.4GHz, 4X4:4 5GHz, 2X2 sensor PoE 802.3at (802.
7 Regulatory Information Professional Installation Instruction Safety Guidelines Federal Communications Commission (FCC) Notice Industry Canada Notice Detachable Antenna Usage Australia Notice Brazil Anatel Statement Hazardous Substances Supplement to Product Instructions NCC Statement CE Information European Waste Electrical and Electronic Equipment (WEEE) Notice Declaration of Conformity in Languages of the European Community Professional Installation Instruction Installation personnel This product is de
Regulatory Information Instructions d'installation professionnelle Personnel d'installation Ce produit est conçu pour une application spécifique et doit être installé par un personnel qualifié qui possède des connaissances sur les RF et les règles associées. L'utilisateur général ne doit pas tenter d'installer ou de modifier le paramètre. Antenne externe Utilisez uniquement les antennes approuvées par le demandeur.
Regulatory Information • • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
Regulatory Information Warning Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 39 cm de distance entre la source de rayonnement et votre corps.
Regulatory Information Group Brand Model number Antenna type Antenna gain (dBi) 2.4 GHz 5 GHz BLE or thread 12 Extreme ML-2452PNA7-01R Panel 1 7.8 10.7 7.8 13 Extreme WS-AIDE10055 Panel 2 10.5 7.5 - 14 Extreme ML-2499HPA8-01 Dipole - - 8 Australia Notice AU co-location MPE Statement This equipment complies with AU radiation exposure limits set forth for an uncontrolled environment.
Regulatory Information Supplement to Product Instructions NCC Statement 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商 號或使用者均不得 擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條低功率射頻電機 之使用不得影響飛航安全及干擾合法通信；經發現有干擾現 象時，應立即停用，並改善至無干擾時 方得繼續使用。前項合法通信，指依電信法規 定作業之無線電通信。低功率射頻電機須忍受合法通 信或工業、科學及醫療用電波輻 射性電機設備之干擾。 無線資訊傳輸設備避免影響附近雷達系統之 操作。 「本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費 者」。 CE Information The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.
Regulatory Information All operational modes: Frequency AP460i AP460e 2.4GHz 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HEW20), 802.11ax (HEW40), 802.15.4 (Thread), Bluetooth (LE) 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), Bluetooth (BR/ EDR, LE) 5GHz 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.11ax (HEW20), 802.11ax (HEW40), 802.11ax (HEW80), 802.11ax (HEW160) 802.
Regulatory Information 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. 4 It is the user's responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Environmental Compliance at Green@extremenetworks.com.
Regulatory Information Danish Undertegnede Extreme Networks erklærer herved, at følgende udstyr Radio LAN device (AP460i/e) overholder de væsentlige krav og øvrige relevante krav i direktiv 2014/53/EU. For fuld tekst af EU's deceleration of Conformity, kontakt venligst Extreme Regulatory Compliance på compliancerequest@extremenetworks.com German Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN Wireless Controller bzw.
Regulatory Information Portuguese Extreme Networks declara que este Radio LAN device (AP460i/e) está conforme com os requisitos essenciais e outras disposições da Directiva 2014/53/EU. Para obter o texto completo da desaceleração de conformidade da UE, entre em contato com a Extreme Regulatory Compliance em compliancerequest@extremenetworks.
Index A Antenna Configurations AP460e access point antenna connectors 34 AP460i/e mounting options accessories 12 optional brackets 12 pole install 12 wall install 12 AP460i/e Power Source 30 Australia notice 41 B box contents AP460e contents 12 AP460i contents 12 C installation procedure (continued) wall Install 14 K KT-147407-02 pole mounting Pole part of the KT-147407-02 bracket 24 L LED LED indicators 9 M Mounting option Pole Mounting 20 Mounting Option VMM bracket installation 18 conventions not
Index Specifications Environmental Specifications 36 Product Specifications 36 support, see technical support T technical support contacting 5 ExtremeMobility AP460i/e Outdoor Access Points 48
