Installation Guide
Table Of Contents
- Table of Contents
- Preface
- AP460i/e Overview
- Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options and Bracket Information
- Position the Access Point before Installation
- Ground Connection
- Install the Access Point on a Wall or to a Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Hard Vehicle Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attach the Access Point to a Pole Using All Three KT-147407-02 Bracket Parts
- Attach the Access Point to a Pole Using the KT-147407-02 Pole Part
- Attach the Access Point to a Pole Using KT-147407-02 Pole Part and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using WS-MBO-POLE01 Bracket and MBO-ART02 Articulating Mounting Bracket
- GE and Console Connections
- Safe Removal of the RJ45 Cable
- Antenna Configuration for External Antenna Model Access Point
- Form a Drip Loop Connection for Cables
- Access Points Specifications
- Regulatory and Compliance Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Agência Nacional De Telecomunicações (Anatel) Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
AP460i/e Overview
AP460i/e Features on page 9
Power Source on page 12
AP460i/e Power Tables on page 12
LED Indicators on page 12
Access Point Purchase Order Information on page 14
The AP460i/e access points are outdoor model enterprise class 802.11ax access points. The “i” in
AP460i indicates that the access point comes with internal antennas and the “e” in AP460e indicates
that it comes with external antenna connectors. The access points feature a dual-band radio, two band-
locked radios, eight WiFi internal or external antennas, and one Bluetooth Low Energy (BLE) antenna.
The AP460i/e can be mounted on a flat surface such as a wall or to a pole.
Note
The AP460i/e requires a minimum base firmware of WiNG 7.3.0.
In this document, the access point is addressed as AP460i/e wherever the procedure and general
information is applicable to both access points.
AP460i/e Features
The AP460i/e access points have the following features:
• Radios:
◦ Three 802.11ax radios (one 2×2 2.4GHz radio, one 4×4 5GHz radio, and one 2×2 2.4GHz and 5GHz
radio)
◦ 1 IoT radio (2.4 GHz)
• Console port: RJ45
• Two Ethernet ports:
◦ 1×100/1000/2500 Mbps auto-negotiation Ethernet port, RJ45
◦ 1×10/100/1000 Mbps auto-negotiation Ethernet port, RJ45
• LEDs: Seven. All LEDs will be on during reset and connect to general-purpose input/output (GPIO)
pins
• One Reset button
• Power: PoE 802.3at (for more information on power used at 802.3af and 802.3at modes, see
AP460i/e Power Tables)
ExtremeWireless™ AP460i/e Access Points
9