Installation Guide
Table Of Contents
- Table of Contents
- Preface
- AP460i/e Overview
- Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options and Bracket Information
- Position the Access Point before Installation
- Ground Connection
- Install the Access Point on a Wall or to a Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Hard Vehicle Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attach the Access Point to a Pole Using All Three KT-147407-02 Bracket Parts
- Attach the Access Point to a Pole Using the KT-147407-02 Pole Part
- Attach the Access Point to a Pole Using KT-147407-02 Pole Part and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using WS-MBO-POLE01 Bracket and MBO-ART02 Articulating Mounting Bracket
- GE and Console Connections
- Safe Removal of the RJ45 Cable
- Antenna Configuration for External Antenna Model Access Point
- Form a Drip Loop Connection for Cables
- Access Points Specifications
- Regulatory and Compliance Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Agência Nacional De Telecomunicações (Anatel) Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
Installation procedure
Refer to the installation instructions for details.
Warning
Select the installation position and make sure that the final output power does not exceed the
limit set forth in relevant rules. The violation of the rule could lead to serious federal penalty.
Instructions d'installation professionnelle
Personnel d'installation
Ce produit est conçu pour une application spécifique et doit être installé par un personnel qualifié qui
possède des connaissances sur les RF et les règles associées. L'utilisateur général ne doit pas tenter
d'installer ou de modifier le paramètre. Les personnes qualifiées sont définies comme des personnes
autorisées à mettre en service une mise à la terre de protection, à étiqueter les dispositifs, les systèmes
et les circuits conformément aux pratiques et normes de sécurité établies. Une personne qualifiée
comprend les exigences et les risques liés à l'installation d'équipements électriques d'extérieur
conformément aux codes nationaux.
Antenne externe
Utilisez uniquement les antennes approuvées par le demandeur. Les antennes non approuvées peuvent
produire une puissance de transmission RF parasite ou excessive indésirable, ce qui peut entraîner la
violation de la limite FCC / IC et est interdite.
Procédure d'installation
Reportez-vous aux instructions d'installation pour plus de détails.
Warning
Sélectionnez la position d'installation et assurez-vous que la puissance de sortie finale ne
dépasse pas la limite indiquée dans les règles pertinentes. La violation de la règle pourrait
entraîner de graves sanctions fédérales.
Safety Guidelines
The following safety guidelines are intended to protect your personal safety and prevent damage to the
equipment.
Important
Only qualified personnel must perform installation procedures. Within the context of the
safety notes in this documentation, qualified persons are defined as persons who are
authorized to commission grounding, label devices, systems, and circuits in accordance with
established safety practices and standards. A qualified person understands the requirements
and risks involved with installing outdoor electrical equipment in accordance with national
codes.
Installation procedure Regulatory and Compliance Information
50 ExtremeWireless™ AP460i/e Access Points