Installation Guide
Table Of Contents
- Table of Contents
- Preface
- AP460i/e Overview
- Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options and Bracket Information
- Position the Access Point before Installation
- Ground Connection
- Install the Access Point on a Wall or to a Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Hard Vehicle Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attach the Access Point to a Pole Using All Three KT-147407-02 Bracket Parts
- Attach the Access Point to a Pole Using the KT-147407-02 Pole Part
- Attach the Access Point to a Pole Using KT-147407-02 Pole Part and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using WS-MBO-POLE01 Bracket and MBO-ART02 Articulating Mounting Bracket
- GE and Console Connections
- Safe Removal of the RJ45 Cable
- Antenna Configuration for External Antenna Model Access Point
- Form a Drip Loop Connection for Cables
- Access Points Specifications
- Regulatory and Compliance Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Agência Nacional De Telecomunicações (Anatel) Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
Procedure
1. Attach one end of the KT-150173-01 extension arm to the access point using two M6 hex-head
screws.
2. Attach the KT-147407-02 pole part to the other end of the KT-150173-01 bracket using two hex-head
M12 stainless-steel screws, and two hex-head M12 stainless-steel nuts.
3. Attach the pole bracket to the pole.
Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the
KT-150173-01 Extension Arm
Before You Begin
You can attach the access point to a pole using all the parts of the KT-147407-02 bracket and the
KT-150173-01 extension arm.
The following hardware is required:
• KT-147407-02 flat part
• KT-147407-02 1-axis tilt part
• KT-147407-02 pole part
• KT-150173-01 extension arm
• Six M6 hex-head screws
• Four hex-head M12 stainless-steel screws and nuts
• Two 0.5 in. (12.7 mm) wide stainless-steel cable clamps
• Access point
About This Task
To install the access point on a pole:
Procedure
1. Attach the KT-147407-02 flat part to the access point.
For instructions on how to attach the bracket parts, see Install the Access Point to a Flat Surface
Using KT-147407-02 Flat Part and 1-Axis Tilt Part.
Attach the Access Point to a Pole Using the
KT-147407-02 Bracket Parts and the KT-150173-01
Extension Arm Install the Access Point
34 ExtremeWireless™ AP460i/e Access Points