Installation Guide
Table Of Contents
- Table of Contents
- Preface
- AP460i/e Overview
- Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options and Bracket Information
- Position the Access Point before Installation
- Ground Connection
- Install the Access Point on a Wall or to a Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Hard Vehicle Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attach the Access Point to a Pole Using All Three KT-147407-02 Bracket Parts
- Attach the Access Point to a Pole Using the KT-147407-02 Pole Part
- Attach the Access Point to a Pole Using KT-147407-02 Pole Part and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using WS-MBO-POLE01 Bracket and MBO-ART02 Articulating Mounting Bracket
- GE and Console Connections
- Safe Removal of the RJ45 Cable
- Antenna Configuration for External Antenna Model Access Point
- Form a Drip Loop Connection for Cables
- Access Points Specifications
- Regulatory and Compliance Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Agência Nacional De Telecomunicações (Anatel) Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
5. Using four M6 hex-head screws, attach the KT-150173-01 extension arm to a flat surface.
Tip
The best practice is to use screw-in anchors with the M6 screws on a wood surface, and
concrete anchors on a concrete surface.
Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
Before You Begin
The KT-150173-01 extension arm is used to install the access point on a flat surface, away from any
obstruction and to get a stronger antenna signal.
The following hardware is required:
• KT-150173-01 extension arm
• Eight M6 hex-head screws
◦ Four M6 hex-head screws to attach one end of the extension arm to the access point
◦ Four M6 hex-head screws to attach the other end of the extension arm to the wall
• Access point
Procedure
1. Using the KT-150173-01 extension arm as a template, mark and drill four hole centers on a flat
surface.
The holes must be within the semi-circular cuts of the extension arm.
2. Using four M6 hex-head screws, attach one end of the KT-150173-01 extension arm to the access
point.
3. Using four M6 hex-head screws, attach the other end of the KT-150173-01 extension arm to the wall.
Tip
The best practice is to use screw-in anchors with the M6 screws on a wood surface, and
concrete anchors on a concrete surface.
Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating
Mounting Bracket
Before You Begin
The following hardware is required:
• MBO-ART02 articulating mounting bracket
• Access point
Install the Access Point
Install the Access Point On a Flat Surface Using the
KT-150173-01 Extension Arm
ExtremeWireless™ AP460i/e Access Points 23