Installation Guide
Table Of Contents
- Table of Contents
- Preface
- AP460i/e Overview
- Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options and Bracket Information
- Position the Access Point before Installation
- Ground Connection
- Install the Access Point on a Wall or to a Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Hard Vehicle Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attach the Access Point to a Pole Using All Three KT-147407-02 Bracket Parts
- Attach the Access Point to a Pole Using the KT-147407-02 Pole Part
- Attach the Access Point to a Pole Using KT-147407-02 Pole Part and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using WS-MBO-POLE01 Bracket and MBO-ART02 Articulating Mounting Bracket
- GE and Console Connections
- Safe Removal of the RJ45 Cable
- Antenna Configuration for External Antenna Model Access Point
- Form a Drip Loop Connection for Cables
- Access Points Specifications
- Regulatory and Compliance Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Agência Nacional De Telecomunicações (Anatel) Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
Figure 7: KT-150173-01 extension arm
The following hardware is required for installation:
• KT-147407-02 flat part
• KT-147407-02 1-axis tilt part
• KT-150173-01 extension arm
• Access point
• Ten M6 hex-head screws
◦ Two M6 hex-head screws to attach the flat part to the access point
◦ Four M6 hex-head screws to attach the 1-axis tilt part to the flat part
◦ Four M6 hex-head screws to attach the KT-150173-01 extension arm to a flat surface
• Two hex-head M12 stainless-steel screws and nuts
Procedure
1. Using two M6 screws, attach the KT-147407-02 flat part to the access point.
2. Place the KT-147407-02 flat part inside the 1-axis tilt part, and attach it using four M6 screws.
3. Using the KT-150173-01 extension arm as a template, mark four hole centers on a flat surface.
The holes must be within the semi-circular cuts of the extension arm.
4. Using two hex-head M12 stainless-steel screws and two M12 hex-head stainless-steel nuts, attach one
end of the KT-150173-01 extension arm to the 1-axis tilt part.
The screws and nuts are fastened through the two large circular holes on the KT-150173- 01 extension
arm.
Install the Access Point to a Flat Surface Using the
KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT-
150173-01 Extension Arm Install the Access Point
22 ExtremeWireless™ AP460i/e Access Points