Installation Guide
Table Of Contents
- Table of Contents
- Preface
- AP460i/e Overview
- Install the Access Point
- AP460i/e Box Contents
- Access Point Mounting Options and Bracket Information
- Position the Access Point before Installation
- Ground Connection
- Install the Access Point on a Wall or to a Flat Surface
- Install the Access Point to a Flat Surface Using KT-147407-02 Flat Part and 1-Axis Tilt Part
- Install the Access Point to a Flat Surface Using the KT-147407-02 Flat Part, 1-axis Tilt Part, and the KT- 150173-01 Extension Arm
- Install the Access Point On a Flat Surface Using the KT-150173-01 Extension Arm
- Install the Access Point on a Flat Surface Using the MBO-ART02 Articulating Mounting Bracket
- Install the Access Point on a Hard Vehicle Surface Using the WS-MBV-VMM Vehicle Bracket (#32216)
- Install the Access Point on a Pole
- Attach the Access Point to a Pole Using All Three KT-147407-02 Bracket Parts
- Attach the Access Point to a Pole Using the KT-147407-02 Pole Part
- Attach the Access Point to a Pole Using KT-147407-02 Pole Part and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using the KT-147407-02 Bracket Parts and the KT-150173-01 Extension Arm
- Attach the Access Point to a Pole Using WS-MBO-POLE01 Bracket and MBO-ART02 Articulating Mounting Bracket
- GE and Console Connections
- Safe Removal of the RJ45 Cable
- Antenna Configuration for External Antenna Model Access Point
- Form a Drip Loop Connection for Cables
- Access Points Specifications
- Regulatory and Compliance Information
- Professional Installation Instruction
- Safety Guidelines
- Federal Communications Commission (FCC) Notice
- Industry Canada Notice
- Detachable Antenna Usage
- Australia Notice
- Brazil Agência Nacional De Telecomunicações (Anatel) Statement
- Hazardous Substances
- Supplement to Product Instructions
- NCC Statement
- CE Information
- European Waste Electrical and Electronic Equipment (WEEE) Notice
- Declaration of Conformity in Languages of the European Community
- Index
Table 9: Mounting bracket usage (continued)
Mounting bracket and
part number
Wall install Pole install Notes
WS-MBO-POLE01
bracket
No Yes. The POLE01 bracket
can only be used with
the MBO-ART02
articulating mounting
bracket
If the pole diameter is
>= 1.0 in. (25.4 mm), use
a small cable clamp. If
the pole diameter is
between 5.0 in. - 7.0 in.
(127.0 mm - 178.0 mm),
use a large cable clamp.
For any other pole
diameter, provide your
own stainless steel cable
clamp. The band must
be 0.5 in. (12.7 mm)
wide.
WS-MBV-VMM vehicle
bracket (#32216)
Yes No The VMM vehicle
bracket has four parts:
• Flat plate with
thumbscrews
• Stiener plate 1
• Stiener plate 2
• Vehicle attach
assembly plate
Note
All mounting brackets are sold separately.
Important
The AP460i/e access points use dierent mounting accessories than the AP460C,
AP460S6C, and AP460S12C series access points.
Position the Access Point before Installation
When you install the access point, the vent must be on the side closest to the ground, and not above
the plastic cover. You must provide a 3.0 in. (76.2 mm) drip loop on all cables. For more information, see
Form a Drip Loop Connection for Cables on page 47.
Note
The sensor and BLE antennas come with a dust cap on them. Do not remove the dust cap
until you are ready to install the antennas.
Related Topics
Ground Connection on page 18
Form a Drip Loop Connection for Cables on page 47
Install the Access Point
Position the Access Point before Installation
ExtremeWireless™ AP460i/e Access Points 17