Altitude™ 4760 Series Access Point Installation Guide Extreme Networks, Inc. 3585 Monroe Street Santa Clara, California 95051 (888) 257-3000 (408) 579-2800 http://www.extremenetworks.
AccessAdapt, Alpine, Altitude, BlackDiamond, EPICenter, ExtremeWorks Essentials, Ethernet Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby Router Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go Purple Extreme Solution, ExtremeXOS ScreenPlay, ReachNXT, Sentriant, ServiceWatch, Summit, SummitStack, Triumph, Unified Access Architecture, Unified Access RF Manager, UniStack, the Extreme Networks logo, the Alpine logo, the BlackD
Table of Contents Chapter 1: Introduction....................................................................................................5 Document Conventions............................................................................................................... 7 Altitude 4760 Series Access Point Hardware ............................................................................. 8 Altitude 4760 Series Access Point Antennas......................................................................
Table of Contents Chapter 4: Specifications ..............................................................................................63 Hardware Specifications ........................................................................................................... 63 Environmental Specifications.................................................................................................... 64 Radio Specifications ..................................................................................
1 Introduction CHAPTER Perfect for extending network coverage to outside areas, the Altitude™ 4760 Series Access Point brings the latest 802.11n 3x3 Multiple Input Multiple Output (MIMO) tri-radio design together with rugged outdoor performance. True perimeter security is provided using either a dedicated dual-band sensor or software mode for both 2.4 GHz and 5 GHz bands to deliver 24x7 rogue detection and termination.
protocol. Extreme Networks Wireless Mobility 5 networks extend the differentiation that Adaptive APs offered to the next level by now having the services and security available at every point in the network. The traffic flow is optimized to prevent wired congestion as well as wireless congestion. Traffic flows dynamically, based on user and application, and finds alternate routes to work around any possible network choke points.
Document Conventions Document Conventions The following graphical alerts are used in this document to indicate notable situations: NOTE Tips, hints, or special requirements that you should take note of. CAUTION Care is required. Disregarding a caution can result in data loss or equipment malfunction. WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage.
Altitude 4760 Series Access Point Hardware Altitude 4760 Series Access Point Hardware There are currently six models of the Altitude 4760 Series Access Point. SKU Part Number Description AP4762-US 15794 Altitude 4762 dual-radio Independent Outdoor Access Point for US regulatory domain, 802.11a/b/g/n, 3x3 MIMO. External antennas. Powered by 802.3at PoE. AP4762-EU 15811 Altitude 4762 dual-radio Independent Outdoor Access Point for European Union regulatory domain, 802.11a/b/g/n, 3x3 MIMO.
Altitude 4760 Series Access Point Antennas Altitude 4760 Series Access Point Antennas The Altitude 4760 Series Access Point antenna suite includes the following options: Altitude 4760 Series Access Point 2.4 GHz Antennas Gain Height (inches) P/N Outdoor, dipole, 8dBi, N-Male, 2.4GHz 2.4 8 19.5 ML-2499-HPA8-01 Outdoor, dipole, 4dBi, N-Male, 2.4GHz 2.4 4 9.0 ML-2499-HPA4-01 Downtilt, 8dBI, N-Male, 2.4 GHz 8 21 RAN4054A Antenna Description Band 2.
Outdoor PoE Hardware and Mounting Accessories Outdoor PoE Hardware and Mounting Accessories The Altitude 4760 Series Access Point is a Power over Ethernet (PoE) device. When deployed, the use of an outdoor rated PoE power supply and mounting bracket may be required. The recommended Extreme Networks PoE accessories are listed in the following table. For more information, see “Altitude 4760 Series Access Point Power Options Using Power over Ethernet” on page 37.
Package Contents Package Contents Carefully remove all protective packing material from around the Altitude 4760 Series Access Point and save the container for later storage and shipping. Refer to “Altitude 4760 Series Access Point Hardware” on page 8 when verifying that all Altitude 4760 Series Access Point hardware has been received. Record the serial numbers on the shipping cartons and Altitude 4760 Series Access Points for warranty claims and reference during software download procedures.
Hardware Installation Guidelines Hardware Installation Guidelines CAUTION All device wiring must comply with the National Electric Code (NEC) or regulations and procedures defined by the regulatory bodies of the country or region where the devices are being deployed. All local building and structure codes must be observed. WARNING! Strictly observe the following safety warnings and precautions when installing an Altitude 4760 Series Access Point.
Warnings ● For the best possible protection, each Access Point requires an LPU be installed adjacent to the Access Point. If there is a LAN connection to an indoor network, a second LPU is required at the cable entry point to the buliding. CAUTION Lightning damage is not covered under the conditions of a standard Extreme Networks product warranty. When installed correctly, Lightning Protection Units (LPUs) provide the best protection from the harmful effects of lightning.
Warnings ● Take precautions to avoid injury from falling tools and equipment. Crews should wear hard hats in and around the installation work site. ● Be aware of vehicular traffic in and around the installation work site. ● Do not operate a portable transmitter near unshielded blasting caps or in an environment where explosives are present unless the transmitter is especially certified for such use.
2 Hardware Installation CHAPTER Altitude 4760 Series Access Point models can be purchased in a two or three radio configuration (see “Altitude 4760 Series Access Point Hardware” on page 8). Each model has two band unlocked radios that can operate across the 2.4 GHz, 4.9 GHz, and 5 GHz bands, subject to country regulatory approval and outdoor/band use.
Altitude 4760 Hardware Overview Altitude 4760 Hardware Overview Altitude 4760 series Access Points can be purchased in a two or three radio configuration (see “Altitude 4760 Series Access Point Hardware” on page 8). Each model has two band unlocked radios that can operate across the 2.4GHz, 4.9GHz, and 5GHz bands, subject to country regulatory approval and outdoor/band use.
Altitude 4760 Series Access Point Ports and Connections Altitude 4760 Access Point Antenna Connectors The Altitude 4762 Series Access Point two radio models (15794, 15795, and 15811) are configured with six N type male connectors to support two active WLAN data radios. When mounting antennas to ports R1-A, R1-B, and R1-C, ensure that you have selected the appropriate band for the configured radio that uses ports R1-A, R1-B, and R1-C.
Altitude 4760 Series Access Point Ports and Connections As with the two radio models, R1 ports relate to the software configured radio 1 settings. When mounting antennas to connectors marked R2-A, R2-B and R2-C, the antenna ports relate to the software configured radio 2 settings. Care must be taken to provide the correct antenna for the operating band of each port. Ports R3-A and R3-B are reserved for the sensor radio. An appropriate multi-band antenna should be mounted on the unit for sensor operation.
Altitude 4760 Series Access Point Ports and Connections Altitude 4760 Series Access Point Console, GE1/POE and GE2 Ports The Altitude 4760 Series Access Point has Ethernet ports for external Console, GE1/POE, and GE2 connections. To gain access to the ports you will need to remove the protective caps.
Altitude 4760 Series Access Point Ports and Connections The Ethernet cable from the PoE device (if used) connects to the GE1/POE port on the unit. The GE2 port on the unit can be used if a second data connection for an external device (e.g. surveillance camera) is required. Ensure the GE2 WAN port has been configured to permit an attached external device during the configuration process. When making connections using these ports, a properly rated RJ45 connector is required.
Altitude 4760 Series Access Point Ports and Connections Altitude 4760 Series Access Point Grounding Screw The grounding screw is located to the right of the GE1/POE port and above the GND symbol. WARNING! The grounding cable for an Altitude 4760 Series Access Point must be at a minimum a #10 gauge wire cross section. The grounding cable can be attached to the unit using one of three recommended methods.
Altitude 4760 Series Access Point Ports and Connections Altitude 4760 Series Access Point Factory Reset Hardware Button An Altitude 4760 Series Access Point can be physically reset using the hardware reset button. The button is located inside the reset port on the bottom of the unit. NOTE This option is not supported by all Altitude 4760 Series Access Point software releases. Refer to the release notes for the appropriate software.
LED Indicators LED Indicators The Altitude 4760 Series Access Point has six LEDs on the top of the Access Point housing. The Access Point utilizes two different colored lights below each LED. Only one light displays within an LED at any given time. Every light within each LED is exercised during startup to allow the user to see if an LED is not functioning. The LEDs turn on and off while rotating in a circular pattern.
LED Indicators Two Radio LEDs A dual-radio model Access Point (part numbers 15794, 15795, and 15811) has the following unique LED behavior: LED 1 (Sensor) LED 2 (2.4 GHz) LED 3 (5 GHz) LED 4 (GE2/WAN) LED 5 (GE1/LAN) LED 6 (System) Not Used Blinking Emerald indicates 802.11b/g/n activity. Blinking Amber indicates 802.11a/n activity. LED Off indicates the port is not connected. LED Off indicates the port is not connected. Solid Red indicates diagnostic mode.
LED Indicators Three Radio LEDs A tri-radio Access Point with sensor (part numbers 15796, 15910, and 15812) has the following unique LED behavior: LED 1 (Sensor) LED 2 (2.4 GHz) LED 3 (5 GHz) LED 4 (GE2/WAN) LED 5 (GE1/LAN) LED 6 (System) Blinking Emerald and Amber at 2 second interval indicates a radio is present but not connected to a server. Blinking Emerald indicates 802.11b/g/n activity. Blinking Amber indicates 802.11a/n activity. LED Off indicates the port is not connected.
Altitude 4760 Series Access Point Hardware Mounting and Installation Altitude 4760 Series Access Point Hardware Mounting and Installation It is recommended to use the Altitude 4760 Series Access Point mounting bracket kit (KT-147407-01) for most deployments. When a standoff distance is required for a pole mounted or wall mounted installation, use the extension arm kit (KT-150173-01).
Altitude 4760 Series Access Point Hardware Mounting and Installation A torque wrench or ratchet with a 10mm adapter, or an adjustable wrench, can be used to assemble the mounting brackets. A finished assembly of the mounting bracket kit is shown below. Assembly during deployment may differ to achieve required angle and rotation for optimal positioning.
Altitude 4760 Series Access Point Hardware Mounting and Installation Extension Arm Kit When mounting an Altitude 4760 Series Access Point on poles more than 3 inches in diameter, use the extension arm kit (P/N KT-150173-01) to provide a minimum standoff distance of twelve inches to avoid interference with the antennas. The extension arm kit can also be used in combination with any of the brackets from the mounting bracket kit.
Altitude 4760 Series Access Point Hardware Mounting and Installation The following ancillary hardware to attach the extension arm to the mounting hardware kit sections is included in the extension arm kit. Description Quantity 1/2 inch hex head nut 2 1/2 inch x 3/4 inch hex head bolt 2 Pole Mounted Installations The mounting hardware kit and extension arm can be used in various combinations to properly install the Altitude 4760 Series Access Point on a pole.
Altitude 4760 Series Access Point Hardware Mounting and Installation Vertical Pole Mount Use the following procedures for vertical pole mount installations. Use of the extension arm is recommended when mounting the Access Point to poles greater than 3 inches is diameter. For Poles Up To 3 Inches In Diameter When Using A U-bolt: 1 Thread the two inner nuts onto the U-bolt. Place the U-bolt at the desired mounting location. 2 Place the pole mount bracket section on the U bolt.
Altitude 4760 Series Access Point Hardware Mounting and Installation 8 With the Access Point positioned so that the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the Access Point bracket section into the open slot connections on the bottom of the angle adapter bracket section. 9 Rotate the Access Point bracket section upward and align the top holes on the sides with the top holes on the angle adapter bracket section.
Altitude 4760 Series Access Point Hardware Mounting and Installation For Mounting with Band Clamps: 1 Attach the pole mount bracket section at the desired mounting location using band clamps. 2 With the angle adapter bracket section positioned so that the open connector slots are on the bottom, attach the angle adapter bracket section to the pole mount bracket section using two 1/2 inch bolts and nuts. Tighten the nuts to 30 inch pounds (lbf-in).
Altitude 4760 Series Access Point Hardware Mounting and Installation 6 Rotate the Access Point bracket section upward and align the top holes on the sides with the top holes on the angle adapter bracket section. Insert two M6 hex flange screws into the top holes on the angle adapter bracket section.
Altitude 4760 Series Access Point Hardware Mounting and Installation Examples for using the extension arm alone, or with the mounting bracket kit for a pole mount installation are shown below. Wall Mounted Installations For wall mounted installations, use only the Access Point bracket and the angle adjust bracket sections. CAUTION Always mount the Altitude 4760 Series Access Point with the black gore vent facing down. NOTE The U-bolt and band clamps are not included in the mounting bracket kit.
Altitude 4760 Series Access Point Hardware Mounting and Installation 2 Using a torque wrench, or a ratchet and a 10mm socket, or an adjustable wrench, attach (but do not tighten) the Access Point bracket section to the Altitude 4760 Series Access Point with four M6 hex flange screws and insert two M6 hex flange screws into the bottom holes on the sides of the Access Point bracket section.
Altitude 4760 Series Access Point Hardware Mounting and Installation 6 To adjust the position of the Access Point, rotate the Access Point bracket section (plus or minus 15 degrees) and tilt the angle adapter bracket section (up to 45 degrees). 7 Tighten all hex flange screws to 60 inch pounds (lbf-in). To use only the extension arm: 1 Using four #10/32 lag bolts, attach the extension arm at the desired mounting location.
Altitude 4760 Series Access Point Power Options Using Power over Ethernet 4 Using a torque wrench, or a ratchet and a 10mm socket, or an adjustable wrench, attach the extension arm to the Access Point with four M6 hex flange screws. Tighten the hex flange screws to 60 inch pounds (lbf-in). Altitude 4760 Series Access Point Power Options Using Power over Ethernet Power over Ethernet (PoE) is the power source for an Altitude 4760 Series Access Point.
Altitude 4760 Series Access Point Power Options Using Power over Ethernet NOTE Product installation and mounting instructions are provided with the outdoor power injector. Refer to the power injector installation guide.
3 Initial Access Point Configuration CHAPTER The Altitude 4760 Series Access Point receives its configuration once it is adopted by an Extreme Networks Summit® WM3000 Series controller. There are no required initial configuration settings beyond verifying power and LED functionality for the Access Point. Once adopted, the Access Point is managed by its connected controller and can receive periodic firmware updates when Extreme Networks releases updates with new controller functionality.
Chapter 3: Initial Access Point Configuration ap4760-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)#service antennatype ap4760 Series-dipole Select antenna gain with following command: ap4760-XXXXXX (config-device-xx-xx-xx-xx-xx-xx-if-radio1)# antenna-gain These changes can also be made in the device profile configuration file. NOTE For FCC and ETSI requirements, set the 2.4GHz radio gain to 8 dBi and set the 5GHz radio gain to 10 dBi.
The Initial Setup Wizard The Initial Setup Wizard Once the Access Point is installed and powered on, complete the following steps to get the device up and running by using the Initial Setup Wizard: 1 Attach an Ethernet cable from the Access Point to a controller with an 802.3af compatible power source or use the PWRS-14000-148R power supply to supply power to the Altitude 4760 Series Access Point (once fully cabled).
Chapter 3: Initial Access Point Configuration 2 Point the Web browser to the Altitude 4760 Series Access Point’s IP address (using https://). The following login screen displays. 3 Enter the default username admin in the Username field. 4 Enter the default password admin123 in the Password field. 5 Click the Login button to load the management interface. NOTE When logging in for the first time, you are prompted to change the password to enhance device security in subsequent logins.
The Initial Setup Wizard The setup wizard displays the first time the Altitude 4760 Series Access Point user interface is accessed in order to define the Altitude 4760 Series Access Point’s initial configuration. 7 If this is the first time the management interface has been accessed, a dialogue displays to start the wizard.
Chapter 3: Initial Access Point Configuration The first page of the Initial AP Setup Wizard displays the Navigation Panel and Introduction for the configuration activities comprising the Access Point's initial setup. A green checkmark to the left of an item in the Navigation Panel means the listed task has its minimum required configuration parameters set correctly. A red X means the task as still requiring at least one parameter be defined correctly.
The Initial Setup Wizard The Introduction screen displays a list of the basic configuration activities supported by the Initial Setup Wizard. 8 Select Save/Commit within each page to save the updates made to that page's configuration. Select Next to proceed to the next page listed in the Navigation Panel. Select Back to revert to the previous screen in the Navigation Panel without saving your updates.
Chapter 3: Initial Access Point Configuration 9 Select Next. The Initial AP Setup Wizard displays the Access Point Type screen to define the Access Point's Standalone versus Virtual Controller AP functionality and the way the Access Point is adopted to a controller.
The Initial Setup Wizard 10 Select an Access Point Type from the following options: ● Virtual Controller AP - When more than one Access Point is deployed, a single Access Point can function as a Virtual Controller AP. Up to 24 Access Points can be connected to, and managed by a single Virtual Controller AP of the same Altitude 4760 Series Access Point model. ● Standalone AP -Select this option to deploy this Access Point as an autonomous fat Access Point.
Chapter 3: Initial Access Point Configuration If you are using the static method, you will also need to define whether the Access Point receives an IP address using DHCP or if IP resources are provided statically.
The Initial Setup Wizard 11 Select Next. The Initial AP Setup Wizard displays the Access Point Mode screen to define the Access Point's routing or bridging mode functionality.
Chapter 3: Initial Access Point Configuration 12 Select an Access Point Mode from the available options. ● Router Mode - In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single Access Point. ● Bridge Mode - In Bridge Mode, the AP depends on an external router for routing LAN and WAN traffic.
The Initial Setup Wizard 13 Select Next. The Initial AP Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface configuration.
Chapter 3: Initial Access Point Configuration 14 Set the following DHCP and Static IP Address/Subnet information for the LAN interface: ● Use DHCP - Select the checkbox to enable an automatic network address configuration. ● Static IP Address/Subnet - Enter an IP Address and a subnet for the Access Point's LAN interface. If Use DHCP is selected, this field is not available.
The Initial Setup Wizard 15 Select Next. The Initial AP Setup Wizard displays the WAN Configuration screen to set the Access Point's WAN interface configuration.
Chapter 3: Initial Access Point Configuration 16 Set the following DHCP and Static IP Address/Subnet information for the WAN interface: ● Use DHCP - Select the checkbox to enable an automatic network address configuration. ● Static IP Address/Subnet - Enter an IP Address/Subnet and gateway for the Access Point's WAN interface. These are required fields ● The port connected to the WAN - Select the port used as the physical Access Point connection to the external network.
The Initial Setup Wizard NOTE The ADSP Sensor Server field displays at the bottom of the screen only if a radio has been dedicated as a sensor. 18 Set the following parameters for the radio: ● Configure as a Data Radio - Select this option to dedicate this radio for WLAN client support in either the selected 2.4 or 5 GHz radio band. - Radio Frequency Band - Select either the 2.4 GHz or 5.0 GHz radio band to use with the radio when selected as a Data Radio.
Chapter 3: Initial Access Point Configuration 19 Select Next. The Initial AP Setup Wizard displays the Wireless LAN Setting screen to define network address and security settings for two WLAN configurations available to the Access Point as part of the Initial Setup Wizard. Once the Access Point has an initial configuration defined, numerous additional WLAN configurations can be set.
The Initial Setup Wizard 20 Set the following parameters for each of the two WLAN configurations available as part of this Initial AP Setup Wizard: ● SSID - Enter or modify the Services Set Identification (SSID) associated with the WLAN. The WLAN name is auto-generated using the SSID until changed by the user. The maximum number of characters is 32. Do not use < > | “ & \ ? , This is a required parameter for each WLAN.
Chapter 3: Initial Access Point Configuration NOTE If you are using the Access Point’s onboard RADIUS server, an additional RADIUS Server Configuration screen displays within the Navigation Panel on the left-hand side of the screen. Use this screen to create user accounts validated when the Access Point authenticates client connection requests to the onboard RADIUS server. 21 Select Next.
The Initial Setup Wizard 22 Refer to the Username, Password, Description, and Actions columns to review credentials of existing RADIUS Server user accounts. Add new accounts or edit the properties of existing accounts as updates are required. 23 Refer to the Add On-Board RADIUS Server Users field to set the following parameters for a user account: ● Username - If you are adding a new user account, create a username up to X characters in length.
Chapter 3: Initial Access Point Configuration 25 Select Next. The Initial AP Setup Wizard displays the Country/Date/Time screen to set device deployment, administrative contact and system time information. The system time can either be set manually or be supplied by a dedicated Network Time Protocol (NTP) resource.
The Initial Setup Wizard 26 Refer to the Country and Time Zone field to set the following device deployment information: ● Location - Define the location of the Access Point. The Location parameter acts as a reminder of where the AP is deployed within the Extreme Networks managed wireless network. ● Contact - Specify the contact information for the administrator. The credentials provided should accurately reflect the individual responding to service queries.
Chapter 3: Initial Access Point Configuration If a screen shows settings not intended as part of the initial configuration, the screen can be selected from within the Navigation Panel and its settings modified accordingly. 32 If the configuration displays as intended, select the Save/Commit button to implement these settings to the Access Point’s configuration.
4 Specifications CHAPTER Hardware Specifications Operating Voltage 36-57 VDC Operating Current Not to exceed 750 mA@48 VDC Power In (PoE) PoE support inbound power - 802.3AT on GE1/POE port Ethernet Ports 2 Gigabit Ethernet ports Dimensions (unit) mounted 28.1cm W x 21.8cx H x 9.4cm D (11.1" W x 8.6" H x 3.7" D) Weight (Unit) 6.4 lbs / 2.
Environmental Specifications Environmental Specifications Operating Temperature -40 to +70 degrees celsius Storage Temperature -40 to +85 degrees celsius Operating Humidity 5-95 percent Operating Altitude 8,000 feet Storage Altitude 30,000 feet Electrostatic Discharge EN61000-4-2.
Networking and Software Specifications Networking and Software Specifications Security Stateful Firewall, IP filtering, NAT, 802.1X, 802.11i WPA2, WPA 24x7 Dual band sensor capabilities * (subject to software license keys and sensor radio SKU) Advanced forensics Connectivity troubleshooting Wireless Intrusion Prevention LiveRF Quality of Service (QoS) WMM, WMM-UAPSD, 802.1p, Diffserv and TOS Routing Layer 3 routing, 802.
Optional Accessories Optional Accessories ● Mounting kit ● Extension arm for mounting kit ● IP66 outdoor rated 802.3AT power injector ● Mounting kit for outdoor IP 66 802.3AT power injector ● External antenna options Basic Troubleshooting Basic troubleshooting recommendations for the Altitude 4760 Series Access Point are listed in the following table: Indication Response LEDs are not lit No power to device: Verify 802.
5 Regulatory Information CHAPTER This device is approved under the Symbol Technologies, Inc. brand AP-7161. Symbol Technologies, Inc. is a wholly owned subsidiary of Motorola Solutions, Inc. (collectively “Motorola”). All Extreme Networks devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
FCC Approval Statement wireless systems operating in the 5470 MHz – 5725 MHz band. These wireless devices are subject to Section 15.407 of our rules and when operating as a master device they are required to implement radar detection and DFS functions. We are continuing our work to develop long-term equipment authorization test procedures that will ensure that the devices comply with our rules that include protecting the TDWR operations.
FCC Approval Statement 6 The requirement for ensuring 30 MHz frequency separation is based on the best information available to date. If interference is not eliminated, a distance limitation based on line-of-sight from TDWR will need to be used. In addition, devices with bandwidths greater than 20 MHz may require greater frequency separation.
FCC Approval Statement 8 A voluntary WISPA sponsored database has been developed that allows operators and installers to register the location information of the UNII devices operating outdoors in the 5470 – 5725 MHz band within 35 km of any TDWR location (see http://www.spectrumbridge.com/udia/home.aspx). This database may be used by government agencies in order to expedite resolution of any interference to TDWRs.
FCC Approval Statement TDWR Location Information TERRAIN ELEVATION FREQUENCY (MSL) [ft] ANTENNA HEIGHT ABOVE TERRAIN [ft] STATE CITY LONGITUDE LATITUDE GA ATLANTA W 084 15 44 N 33 38 48 5615 MHz 962 113 IL MCCOOK W 087 51 31 N 41 47 50 5615 MHz 646 97 IL CRESTWOOD W 087 43 47 5 N 41 39 05 645 MHz 663 113 IN INDIANAPOLIS W 086 26 08 N 39 38 14 5605 MHz 751 97 KS WICHITA W 097 26 13 N 37 30 26 5603 MHz 1270 80 KY COVINGTON CINNCINNATI W 084 34 48 N 38 53 53 5610 MHz 94
Wireless Country Approvals OH DAYTON W 084 07 23 N 40 01 19 5640 MHz 922 97 OH CLEVELAND W 082 00 28 N 41 17 23 5645 MHz 817 113 OH COLUMBUS W 082 42 55 N 40 00 20 5605 MHz 1037 113 OK AERO. CTR W 097 37 31 N 35 24 19 5610 MHz 1285 80 W 097 37 43 N 35 23 34 5620 MHz 1293 97 TDWR #1 OK AERO.
Health and Safety Recommendations Operation of the device without regulatory approval is illegal. Health and Safety Recommendations The Federal Communications Commission (FCC) with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. Extreme Networks products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991.
Power Supply Reduce RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. Remote and Standalone Antenna Configurations To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 28 cm from all persons. Power Supply Use only a power-over Ethernet 802.3at compliant solution.
Radio Frequency Interference Requirements - FCC Radio Frequency Interference Requirements FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CE Marking and European Economic Area (EEA) Radio Transmitters This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Statement of Compliance Statement of Compliance Extreme Networks hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www.extremenetworks.com/go/rfcertification.htm. Other Countries Australia Use of 5 GHz RLAN’s in Australia is restricted in the following band: 5.50 – 5.65 GHz.
Statement of Compliance Mexico Restrict Frequency Range to: 2.450 – 2.4835 GHz. Taiwan NOTICE! According to: Administrative Regulations on Low Power Radio Waves Radiated Devices Article 12 Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices.
Statement of Compliance Wireless device operates in the frequency band of 5.25-5.35 GHz, limited for indoor use only. 在 5.25-5.
Waste Electrical and Electronic Equipment (WEEE) Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Extreme Networks for recycling. For information on how to return product, please go to: http://www.extremenetworks.com/go/eu-weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Extreme Networks pour recyclage.
Waste Electrical and Electronic Equipment (WEEE) Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Extreme Networks-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.extremenetworks.com/go/eu-weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Extreme Networks til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.extremenetworks.com/go/eu-weee.
6 Customer Support CHAPTER NOTE Services can be purchased from Extreme Networks or through one of its channel partners. If you are an end-user who has purchased service through an Extreme Networks channel partner, please contact your partner first for support. Extreme Networks Technical Assistance Centers (TAC) provide 24x7x365 worldwide coverage. These centers are the focal point of contact for post-sales technical and networkrelated questions or issues.
Documentation Documentation Check for the latest versions of documentation on the Extreme Networks documentation website at: http://www.extremenetworks.
