User Guide High Definition VideoScope Model HDV600 NEW FACEPLATE OLD FACEPLATE
Introduction Congratulations on your purchase of this Extech HDV600 series Video Borescope. This instrument is designed for use as a remote inspection device. It can be used to peer into tight spots, record and playback real-time video and images. Typical applications include HVAC inspection, automotive inspection, cable routing, and automotive/boat/aircraft inspection. The monitor is designed with dual left or right handed controls for maximum flexibility and is available with a full line of accessories.
Description Monitor 1. Probe connector 2. View Direction button (will now toggle side view and front view camera lens) 3. Video/Camera button ( takes photo) 4. Rotate image button 5. Display 6. Zoom buttons 7. Light intensity buttons 8. Power Button 9. Scroll buttons )short press photo, long press start video, short press in video 10. 11. 12. 13. 14. 15.
Setup Battery Charging and Status Indication: Note: A fully charged battery will allow approximately 5 hours of continuous use. 1. Turn the meter off and then connect the AC adaptor to charge the meter. 2. After several hours, turn the meter on. The battery icon will indicate either: A: Fully charged B: Charge in progress 3. If the battery is charged, remove the AC adaptor and observe that the fully charged 4 bar icon appears. 4.
Operation 1. Connect the probe to the monitor. 2. Press the Power button to turn the monitor on. 3. Maneuver the probe into position to view the area to be examined. The probe can be bent into the shape of the area to be examined. Optimum focus distance is 2 to 6cm (0.79 to 2.3”) 4. Optimum focus distance is probe dependent, but the typical range is 2 to 6cm Zoom Press the or zoom buttons to increase or decrease the display resolution from 1X to 2X.
Articulating probe The articulating probe, with adjustable tip angle, is used for improved viewing angles and optimum inspection when the probe is inserted into the inspection location. The articulating probe is available in a direct (wired) or wireless version. Describe the two camera probe (forward and side) Wireless version Note: The battery must be fully charged for wireless operation. A weak battery may result in meter shut down. 1. Connect the AC adaptor to the transmitter and charge the battery. 2.
Wireless transmitter The wireless transmitter is intended for use in areas that are difficult to access or in situations when is hard to maneuver the probe with the display attached. The probe can also be connected directly to the monitor using the patch cord. Note: The battery must be fully charged for wireless operation. A weak battery may result in meter shut down. Wireless Mode 1. Connect the AC adaptor to the transmitter and charge the battery. 2. Attach the probe to the transmitter. 3.
Viewing a Stored Photo or Video in the Display 1. Press the ▲ button to access the pictures or videos in memory. Each button press will step through the files with the file number appearing on the screen (i.e. IMG00005) 2. Pictures will appear with the 3. Videos will appear with the 4. To play a video, select a video file and press the during playback. Press the appear. photo icon on the display. film icon on the display. button. The button again to pause playback.
Reset button If the monitor becomes unresponsive due to an EMI field or other magnetic event, use a paper clip or other pointed object to press the RESET button located on the bottom panel Rear stand The rear stand can be set to three positions. Lower (stored), middle position for bench viewing and upper position for hanging. FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2.
Specifications Monitor 14.5cm (5.7”); Viewable: 13.5cm (5.3”) Active matrix, 640x480 pixels Interface Mini USB 1.1 and AV out Recording medium SD Card SD memory 2GB maximum Compression format MPGE4 Still image format JPEG (640x480) Video Recording Format AVI (640x480) Video output Format NTSC and PAL Receiver Frequency 2.4GHz Receiver Sensitivity -87dBm (SNR = 42dB, Fmod = 15kHz) Video System NTSC / PAL Data Video / Audio Audio type Stereo Tripod mount On rear, Accepts standard tripod screw Battery 3.
Camera Imaging Sensor Video Format Brightness Control Lamp Type Interface Waterproof Capacity Operating Temperature CMOS NTSC Manual LED Composite Video IP57 -10°C to 50°C (14°F to 122°F) Probes and Cameras Articulation Accessories Part Number HDV-TX1 HDV-WTX1 HDV-TX2 HDV-WTX2 HDV-4CAM-1FM HDV-5CAM-1FM HDV-5CAM-3F HDV-5CAM-3FM HDV-5CAM-10F HDV-5CAM-1RM HDV-5CAM-3R HDV-5CAM-3RM HDV-25CAM-10G HDV-25CAM-30G 240 °±20 ° manual tip articulation Mirror, magnet and anti-snag Ball (excluding 25mm diameter cables
Warranty FLIR Systems, Inc. warrants this Extech Instruments brand device to be free of defects in parts and workmanship for one year from date of shipment (a six month limited warranty applies to sensors and cables). If it should become necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service Department for authorization. Visit the website www.extech.com for contact information.
Garantie FLIR Systems, Inc. garantit que cet appareil Extech Instruments est exempt de défauts matériaux et de fabrication pendant un an à partir de la date d’envoi (une garantie limitée de six mois s’applique aux capteurs et aux câbles). Si le renvoi de l’appareil pour réparation devient nécessaire durant ou après la période de garantie, contactez le service client pour autorisation. Pour obtenir les coordonnées, visitez le site Web suivant : www.extech.com.
Garantía FLIR Systems, Inc., garantiza este dispositivo marca Extech Instruments para estar libre de defectos en partes o mano de obra durante un año a partir de la fecha de embarque (se aplica una garantía limitada de seis meses para cables y sensores). Si fuera necesario regresar el instrumento para servicio durante o después del periodo de garantía, llame al Departamento de Servicio a Clientes para obtener autorización. Visite www.extech.com para Información de contacto.
