USER MANUAL Video Borescope Wireless Inspection Camera Models BR200, BR250, and KITS Additional User Manual Translations available at www.extech.
Introduction Thank you for selecting the Extech Video Borescope Model BR200 (17mm camera), BR250 (9mm camera), BR250-4 (4.5mm camera), or BR250-5 (5.2mm). Extech’s Video Borescope Inspection Cameras provide a glare-free close-up field of view. They include a 3.5" color TFT LCD wireless monitor that can be detached from the base and viewed from a remote location up to 10m (33 ft.) from the measurement point.
Safety Do not expose instruments to moisture Turn power OFF when instruments are not in use Remove the batteries from the Camera controller when cleaning Replace all batteries at the same time Supplied Equipment 1. Camera controller 2. Color TFT monitor 3. AC adaptor for monitor’s rechargeable battery 4. Video cable for connecting additional monitor 5. Accessories (magnet, hook, mirror) BR200/BR250 only 6. Magnetic mount for monitor 7. Flexible cable and camera head 8.
Description 1 Monitor mount (signal output) 2 Camera controller power indicator 3 Camera controller power ON/OFF switch and LED dimmer 4 Flexible cable 5 Camera head and LEDs 6 OK button 7 Up arrow and video/image button 8 Menu button 9 Down arrow button 10 Monitor power ON/OFF button 11 Monitor power indicator 12 USB jack for PC connection 13 Video output jack for alternate monitor 14 SD card slot 15 AC power adaptor jack 16 Reset button 17 Monitor mount (input signal) 4 BR200-BR250-KIT
Preparation for use Camera controller power Insert the four (4) ‘AA’ batteries (supplied) into the battery carrier located in the camera controller’s handle as illustrated in accompanying diagrams. Observe correct polarity when installing batteries. Never dispose of used batteries or rechargeable batteries in household waste. As consumers, users are legally required to take used batteries to appropriate collection sites, the retail store where the batteries were purchased, or wherever batteries are sold.
Inserting the micro SD card Insert card with arrow pointing toward slot. Gently apply pressure until the card locks into the spring loaded slot. To remove, gently push the card inward and then release to eject it from the card slot. Please use a Class 6 or better TF Flash memory card. Attaching the monitor to the camera controller Insert the monitor’s plug into the jack at the back of the camera controller and slide the monitor downward to lock it into position. See accompanying diagram.
8. Use the supplied accessories to help locate and retrieve small items (BR200 and BR250 only). Refer to the separate section in this manual for connecting the attachment accessories. Capturing still images Use the up arrow button on the Monitor to select the Image mode, and then press OK to capture a still image. The image will automatically save to the SD card.
Delete a single video or image 1. 2. 3. 4. 5. 6. 7. 8.
Hook, mirror, and magnet accessories for the BR200 The supplied BR200 accessories (mirror, hook and magnet) all attach to the camera in the same manner. Refer to the diagrams below. Note that these accessories are not compatible with the BR250-4. Hook, mirror, and magnet accessories for the BR250 The supplied BR250 accessories (mirror, hook and magnet) all attach to the camera in the same manner.
Settings Menu Long press this button to enter the Settings Menu. Four icons will appear. The System settings icon (green) is on the upper left, the Date/Time settings icon (yellow) is on the upper right, the Recorder settings icon (red) is on the lower left, and the Playback* icon (blue) is on the lower right. Use the arrow buttons▼▲to step through the icons and use the OK button to open one of the setting modes. Short press to back out of menus as needed.
Restoring Factory Default Settings 1. 2. 3. 4. 5. 6. In the Settings Menu, use▼▲buttons to select the System setting (green icon) Press OK to call up the System icon list Use the arrows to highlight the DEFAULT icon (red) Press OK and the DEFAULT selection screen will appear (YES, NO) Use the arrows to highlight YES (factory default) or NO (leave unchanged) Press OK to accept the selection 7.
Setting Still Image or Video as default Record mode 1. 2. 3. 4. 5. 6. In the Settings Menu, use the▼▲buttons to select Recorder settings (red icon) Press OK to call up the Recorder Mode options Use the arrows to select the Recording mode icon (blue) Press OK to open the parameter Use the arrows to highlight the Still image or Video icon Press OK to confirm 7. Press the button to return to the main Settings Menu or use the arrows to move to another icon in the Recorder settings menu Date/Time Setting 1.
Specifications CAMERA and CAMERA CONTROLLER Imaging sensor Total pixels (NTSC) Horizontal view angle Focal distance Minimum illumination Wireless transmission frequency Wireless modulation type Wireless bandwidth Wireless range Waterproof capacity Operating temperature Power supply Dimensions (controller) Weight (controller) Camera-head diameter CMOS BR200: 712 x 486; BR250, BR250-4, BR250-5: 640 x 480 BR200: 50 degrees; BR250: 45 degrees; BR250-4: 63 degrees; BR250-5: 48 degrees BR200: 20cm (8”); BR250: 1
Copyright © 2014-2020 FLIR Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form www.extech.com 14 BR200-BR250-KITS_en-GB_v9.
