User Manual

- 13 -
2.10.6 Deck: Full floating deck is attached to out-front support frame. Six anti-scalp
rollers provide maximum turf protection. Deck design allows for bagging, mulching
or side discharge.
2.10.7 Deck Depth: 5.5” (14.0 cm)
2.10.8 Cutting Height Adjustment: an extra-long cushioned lever is used to adjust the
cutting height from 1 1/2” (3.8 cm) to 5” (10.2 cm.) in 1/4”(6.4 mm) increments.
The cutting height adjustment handle has a transport position and all adjustments
can be made while the operator remains seated. Units also have a foot operated
deck lift assist lever to aid in raising the deck.
2.10.9 Mulching Kit: Optional.
2.11 DIMENSIONS
2.11.1 Overall Width:
without deck deflector up deflector down
60” Deck 54.5 in. (138.4 cm) 61.4 in. (156.0 cm) 72.2 in. (183.4 cm)
72” Deck 58.5 in. (148.6 cm) 73.2 in. (185.9 cm) 84.3 in. (214.1 cm)
2.11.2 Overall Length:
Roll Bar – Up Roll Bar - Down
60” Deck 82.2 in. (208.8 cm) 92.3 in. (234.4 cm)
72” Deck 86.0 in. (218.4 cm) 96.1 in. (244.1 cm)
2.11.3 Overall Height:
Roll Bar - Up Roll Bar - Down
60” Deck 73.7 in. (187.2 cm) 55.6 in. (141.2 cm)
72” Deck 73.7 in. (187.2 cm) 55.6 in. (141.2 cm)
NOTE: Height will vary slightly depending on seat setting
2.11.4 Tread Width: (center to center of tires, widthwise)
Drive Wheels Casters
60” Deck 42.8 in. (108.7 cm) 38.9 in. (98.8 cm)
72” Deck 46.8 in. (118.9 cm) 47.6 in. (120.9 cm)
2.11.5 Wheel Base: (center of caster to center of drive tire)
60” Deck 54.0 in. (137.2 cm)
72” Deck 56.8 in. (144.3 cm)
2.11.6 Curb Weight:
60” Deck 1639 lbs. (743 kg)
72” Deck 1657 lbs. (752 kg)
2.12 TORQUE REQUIREMENTS
Bolt Location Torque
Cutter Housing Spindle Nut............................................ 140-145 ft-lbs. (190-197 N-m)
Blade Mounting Bolt....................................................... 115-120 ft-lbs. (156-163 N-m)
Jack Shaft Spindle Nut................................................... 75-80 ft-lbs. (102-108 N-m)
Engine Deck/Front Frame Mount ................................... 30-35 ft-lbs. (41-48 N-m)
Anti-Scalp Roller Bolts ................................................... 40-45 ft-lbs. (54-61 N-m)
Starter Mounting Bolts (M10) ......................................... 22-27 ft-lbs. (30-37 N-m)
Water Separator Mounting Bolts (M8) ............................ 11-14 ft-lbs. (15-19 N-m)
Hydraulic Oil Filter Head Mounting Bolts (M6)................ 60-72 in-lbs. (7-8 N-m)
Wheel Lug Nuts ............................................................. 90-95 ft-lbs. (122-129 N-m)
Wheel Motor Mounting Bolts .......................................... 72-77 ft-lbs. (98-104 N-m)
Wheel Hub Slotted Nut................................................... minimum125 ft-lbs. (169 N-m)
Rollover Protection System (Roll Bar) Mounting Bolts.... 30-35 ft-lbs. (41-47 N-M)