User Guide QA-805 and W2CM Interface Module
Copyright © 2013 EXFO Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, be it electronically, mechanically, or by any other means such as photocopying, recording or otherwise, without the prior written permission of EXFO Inc. (EXFO). Information provided by EXFO is believed to be accurate and reliable.
Contents Certification Information ........................................................................................................ v 1 Introduction ................................................................................................. 1 QA-805 Features .....................................................................................................................1 Front View of QA-805 ..................................................................................................
7 Warranty ......................................................................................................39 General Information .............................................................................................................39 Liability .................................................................................................................................40 Exclusions ...............................................................................................................
Certification Information Certification Information North America Regulatory Statement This unit was certified by an agency approved in both Canada and the United States of America. It has been evaluated according to applicable North American approved standards for product safety for use in Canada and the United States. Electronic test and measurement equipment is exempt from FCC part 15, subpart B compliance in the United States of America and from ICES-003 compliance in Canada. However, EXFO Inc.
Certification Information DECLARATION OF CONFORMITY Application of Council Directive(s): 1999/5/EC – The R&TTE Directive 2011/65/UE – Restriction of the use of certain hazardous substances (RoHS) And their amendments Manufacturer’s Name and Address: EXFO Inc. 400 Godin Avenue Quebec City, Quebec G1M 2K2 CANADA Tel.: +1 418 683-0211 Equipment Type/Environment: Trade Name/Model No.
Certification Information DECLARATION OF CONFORMITY Application of Council Directive(s): 1999/5/EC – The R&TTE Directive 2011/65/UE – Restriction of the use of certain hazardous substances (RoHS) And their amendments Manufacturer’s Name and Address: EXFO Inc. 400 Godin Avenue Quebec City, Quebec G1M 2K2 CANADA Tel.: +1 418 683-0211 Equipment Type/Environment: Trade Name/Model No.
1 Introduction EXFO’s QualityAssurer™ QA-805 is targeted at NEMs and NSPs that are developing and deploying IMS and wireless networks. The QA-805 offers easy-to-use test solutions covering the complete testing life cycle of LTE, IMS, VoLTE, and VoIP networks and services. QA-805 Features Six-unit rack-mounted Emulation of over 5 million LTE or IMS subscribers 8 million data sessions 1.
Introduction Front View of QA-805 Front View of QA-805 This image of the QA-805 chassis provides a realistic view of the front panel. See the section Chassis Front Panel on page 4, for further details that identify specific parts of the QA-805.
Introduction Rear View of QA-805 Rear View of QA-805 This image of the rear panel on the QA-805 provides a realistic view of the back of the chassis. See the section Chassis Back Panel on page 5 for details of the QA-805 rear panel.
Introduction Physical Description of QA-805 Unit Physical Description of QA-805 Unit Chassis Front Panel The following is a picture of the front of the QA-805 rack-mount model. 1. Right Fan Tray [FT1] 2. Left Fan Tray [FT2] 3. Power supplies cover and air filter holder 4. Control Board/Slot 2 [SHMC2] (not populated) 5. Control Board/Slot 1 [SHMC1] (Shelf Manager) 6. Backplane 7. ESD (Electrostatic Discharge) Wrist Strap Terminal (Banana Jack) 8. Rack ears for mounting in 19” rack 9.
Introduction Physical Description of QA-805 Unit 10. Power supply unit/slot 2 11. Power supply unit/slot 3 12. Power supply unit/slot 4 Chassis Back Panel The following is a picture of the back of the QA-805 chassis. 13. Shelf Ground Terminals 14. Individual Power Switch for each power supply 15. Individual AC Inlet for each power supply 16. ESD Wrist Strap Terminal (Banana Jack) 17. Power Bridge slot 18.
Introduction Physical Description of QA-805 Unit Backplane The QA-805 provides a monolithic backplane. Power and high speed links are routed on the same stack up. The backplane supports the following: 6 AdvancedTCA front board slots 6 AdvancedTCA RTM (Rear Transmission Module) slots 2 fan trays 4 power supply slots Physical Layout The physical layout of FRUs (field replacement units) populated in the shelf is shown below.
Introduction Physical Description of QA-805 Unit Rear FRU Physical Layout Logic Ground Logic ground is used as reference for low voltage electronics and is isolated from the chassis/shelf ground and 48 V power lines. For EMI/EMC purposes, it might be needed to connect the logic ground and shelf ground together. To connect both grounds, a screw with a conductive metal washer is installed in this location (GND) as shown in the following picture. To disconnect, remove this screw.
Introduction Physical Description of QA-805 Unit Note: The screw is installed by default.
Introduction Cooling Assembly Cooling Assembly Fan Tray There are 2 fan tray cassettes in the system. The cooling is performed side to side. While the fan tray is a single mechanical block, it has 2 functions: front board cooling and RTM cooling. The front and rear blanks are necessary for proper airflow. The fan tray contains electronics such that it is detected as a fully PICMG compliant IPMC by the shelf manager. It contains hot-swap circuitry, common fusing, fan supervising, and control circuitry.
Introduction Cooling Assembly The following depicts the fan tray with air filter frame: To remove the fan tray: 1. Loosen the locking mechanism and move the head to the left or right (away from the fan tray). 2. Hold the head while pulling out the fan tray using the handle. To insert the fan tray: 1. Loosen the locking mechanism and move the head to the left or right (away from the fan tray). 2. Hold the head while inserting the fan tray using the handle. 3. Tighten the locking mechanism.
Introduction Cooling Assembly CAUTION Rotating fan blades can cause injury or cut. Keep hands clear when servicing. Allow time for fan blades to slow to a stop before fully removing. CAUTION Electrostatic Discharge (ESD) Sensitive Equipment: To avoid damage due to electrostatic discharge, all removable cards must be stored and handled using approved ESD protective packaging. When removing and installing cards use a grounding wrist strap and work in an approved ESD safe work area.
Introduction Cooling Assembly Air Filter The air filter provides: Filtration of intake air from dust particles Additional static pressure to achieve uniform airflow Air filter frame is mounted on the right fan tray cassette. To change the air filter: 1. Extract the fan tray (FT1, right side looking from front). 2. Replace only the filter material. 3. Re-use the filter frame.
Introduction Power Supplies Power Supplies Up to 4 AC power supplies can be plugged in the shelf. The Blutek BPA-R850-480A power supply is shown below and features the following: Total output power 850 W-48 VDC output under 90-264 V input AC frequency range 47-63 Hz EMI filter EN55022 Class B, FCC Part 15 Active PFC = 0.
Introduction Power Supplies Powering the Shelf For each power supply, a separate AC inlet as well as switch is provided. Use power cords rated for currents which exceed the maximum power supply current. CAUTION When working near the power supply power inlets, the shelf operating voltage falls into 90 - 264 V range. This voltage is considered hazardous.
Introduction QA-805 Technical Specifications QA-805 Technical Specifications Physical Dimensions Width: 482.60 mm (19 in) Height: 265.90 mm (10.47 in) Depth: 388.45 mm (15.29 in) Weight: 25.50 kg (56 lbs) D (cable trays): 466.15 mm (18.
Introduction Conventions Conventions Before using the product described in this guide, you should understand the following conventions: WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Do not proceed unless you understand and meet the required conditions. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Do not proceed unless you understand and meet the required conditions.
2 Safety Information Laser Safety Warnings WARNING Do not install or terminate fibers while a light source is active. Never look directly into a live fiber and ensure that your eyes are protected at all times. WARNING The use of controls, adjustments and procedures other than those specified herein may result in exposure to hazardous situations or impair the protection provided by this unit.
Safety Information Operating Cautions CAUTION Use only EXFO-supplied or approved Class 1 SFP, SFP+, or XFP optical transceivers. Operating Cautions CAUTION Rotating fan blades can cause injury or cut. Keep hands clear when servicing. Allow time for fan blades to slow to a stop before fully removing. CAUTION Electrostatic Discharge (ESD) Sensitive Equipment: To avoid damage due to electrostatic discharge, all removable cards must be stored and handled using approved ESD protective packaging.
Safety Information Installation Instruction Warnings Installation Instruction Warnings Rack Mounting If rack mounted units are installed in a closed or multi-unit rack assembly, they may require further evaluation by Certification Agencies. The following items must be considered: 1. The ambient temperature within the rack may be greater than room temperature. Installation should be such that the amount of air flow required for safe operation is not compromised.
Safety Information Installation Instruction Warnings Card Installation Cards installed in the QA-805 unit are hot-swap tolerant but should only be hot-swapped when not in use by an application. Cooling To ensure optimum cooling within the chassis, all empty slots in the chassis (front and back) must be filled with the appropriate sized Filler Panel/Air Baffle. CAUTION Ensure that cards are plugged in parallel to the slot. Applying downward force may result in damage to cards.
Safety Information Equipment Ratings Equipment Ratings Equipment Ratings Temperature Operation 0 °C to 40 °C (32 °F to 104 °F) Storage –40 °C to 70 °C (–40 °F to 158 °F) Relative humiditya 95 % non-condensing Maximum operation altitude 2000 m (6562 ft) Pollution degree 2 Overvoltage category II Input powerb unit 850 W each power cord a. b. 100 - 240 V; 50/60 Hz; 11/5 A Measured in 0 °C to 31 °C (32 °F to 87.8 °F) range, decreasing linearly to 50 % at 40 °C (104 °F).
3 Getting Started Shelf Installation CAUTION Improper installation might cause system damage or personal injury. Consider the following guidelines: 1. Install the system only in an area with restricted access. 2. Follow the installation rules governed in your country. 3. Power distribution to the shelf must include over current protection devices. 4. Use appropriate protective bonding conductor according to over current limits for power lines. 5.
Getting Started Turning the Unit On/Off Turning Off the Unit To safely turn off the QA-805, please ensure the following steps are taken: 1. Stop all test applications and save results to prevent measurement loss. 2. Power down the Processor v1(AM4020M System Controller) by pulling out the HotSwap switch to its first click position. Wait until the Blue HotSwap LED stops flashing and turns Solid Blue to indicate that the System Controller has shut down safely. 3.
4 W2CM-10Gb Ethernet Interface Series The W2CM-10GbE module tests fixed-mobile converged networks and services like wireless (2G/3G/LTE), IMS, VoLTE, and VoIP. It is specially designed for signaling and user-plane testing of network elements such as the P-GW, S-GW, eNodeB, SBC, CSCFs, BGF, HSS, and IMS application servers. With EXFO’s QA-805, the W2CM-10GbE, W2CM-10GbE Lite, and W2CM-4GbE modules can emulate tens of millions of subscribers, generating real-world traffic toward LTE, IMS, and VoIP networks.
W2CM-10Gb Ethernet Interface Series Module Installation W2CM-10GbE Lite/W2CM-4GbE 1-slot module Module Installation The W2CM modules are hot-swappable, but care must be taken when and how the modules are removed. Inserting a Module Follow these steps to insert a module into the QA-805 Chassis: 1. Remove any Filler Cards/Air Baffles required, to provide space for the module being inserted. 2.
W2CM-10Gb Ethernet Interface Series Module Installation 6. Ensure levers fully lock into the closed position. If the chassis is powered up, the Blue HotSwap LED flashes briefly and then turns off. 7. Secure the module to the chassis with the screws on either side of the module. 8. If required, connect the External Time Sync cables to the card to provide the synchronized hardware based timestamps for test measurements. 9. Re-insert any cables into the test-port as required.
W2CM-10Gb Ethernet Interface Series 10/100/1000 M Copper and 1 G Optical Interfaces (SFP) 10/100/1000 M Copper and 1 G Optical Interfaces (SFP) Eight SFP interfaces are available on the faceplate for either optical or copper plugable SFPs. Neither copper nor optical SFPs have built-in LEDs consequently two LEDs per SFP are positioned right beside each SFP cage.
W2CM-10Gb Ethernet Interface Series 10/100/1000 M Copper and 1 G Optical Interfaces (SFP) LED definition for 1 G optical SFP: LED# Label Color 1 Activity Off Definition Idle Green Unidirectional Activity RX Yellow Bidirectional Activity Red LED# Label Color 2 Laser On/Signal Off Unidirectional Activity TX Definition Laser off Green Laser on - signal, with link Yellow Laser on - signal, no link Red Laser on - no signal 10/100/1000 M Copper SFP The component for the copper SFP is
W2CM-10Gb Ethernet Interface Series 10/100/1000 M Copper and 1 G Optical Interfaces (SFP) 1 G Optical SFP The following optical Class 1 Laser SFPs from Finisar are supported: Output Power (dBm) EXFO Product # Transceivers (Finisar) Rx Sensitivity (dBm) FTB-8590 FTLF8519P2BNL 1000BASE-SX Multi-rate: GigE, 1xFC, 2xFC MIN = -9 MAX= -3 (@ GigE) MIN = n/a MAX = -20 850 nm SR /500 m FTB-8591 FTRJ1319P1BTL 1000BASE-LX Multi-rate: GigE, 1xFC, 2xFC MIN = -9.
W2CM-10Gb Ethernet Interface Series 10 G LAN/WAN Optical Interfaces (SFP+) 10 G LAN/WAN Optical Interfaces (SFP+) Two Class 1 Laser SFP+ interfaces are available on the faceplate. On the host side, these SFP+ interfaces are connected directly to the LIM FPGA. The following optical SFP+ from Finisar, are supported: Output Power (dBm) EXFO Product # Transceivers (Finisar) Rx Sensitivity (dBm) FTB-8690 FTLX8571D3BCL Multi-rate 9.95-10.3 Gbit/s 10GBASE-SR/SW MIN = -5 MAX = -1 @ 10.3 Gbit/s MIN = -11.
W2CM-10Gb Ethernet Interface Series 10 G LAN/WAN Optical Interfaces (SFP+) LED definition for 10 G optical SFP+: LED# Label Color 1 Activity Off Idle Green Unidirectional Activity RX Yellow Bidirectional Activity Red LED# Label Color 2 Laser On/Signal Off Unidirectional Activity TX Definition Laser off Green Laser on - signal, with link Yellow Laser on - signal, no link Red 32 Definition Laser on - no signal QA-805 and W2CM Interface Module
5 Maintenance To help ensure long, trouble-free operation: Always inspect fiber-optic connectors before using them and clean them if necessary. Keep the unit free of dust. Clean the unit casing and front panel with a cloth slightly dampened with water. Store unit at room temperature in a clean and dry area. Keep the unit out of direct sunlight. Avoid high humidity or significant temperature fluctuations. Avoid unnecessary shocks and vibrations.
Maintenance Fan Tray Replacing To replace the ATCA card cage air filter, perform the following: 1. Slowly remove the right fan tray. 2. Remove the screws from the filter on the fan tray. 3. Remove the filter from the card cage. 4. Remove the dust from the fan tray with a soft brush. 5. Insert a new filter in the frame and screw it on the fan tray. 6. Insert the fan tray in the system. To replace the AC power supplies filter, perform the following: 1. Remove the front panel covering the power supply slots.
Maintenance Recycling and Disposal (Applies to European Union Only) Recycling and Disposal (Applies to European Union Only) For complete recycling/disposal information as per European Directive WEEE 2012/19/UE, visit the EXFO Web site at www.exfo.com/recycle.
6 Troubleshooting Contacting the Technical Support Group To obtain after-sales service or technical support for this product, contact local EXFO Navtel Product Group representative at one of the following numbers. For detailed information about technical support, visit the EXFO Web site at www.exfo.com. Technical Support Group 160 Drumlin Circle Concord, ON L4K 3E5 CANADA 1 800 267-7235 (USA and Canada) Tel.: 1 905 738-3741 Email: info@exfo.
Troubleshooting Transportation Transportation Maintain a temperature range within specifications when transporting the unit. Transportation damage can occur from improper handling. The following steps are recommended to minimize the possibility of damage: 38 Pack the unit in its original packing material when shipping. Ensure all cards are secured with the screws provided. Avoid high humidity or large temperature fluctuations. Keep the unit out of direct sunlight.
7 Warranty General Information EXFO Inc. (EXFO) warrants this equipment against defects in material and workmanship for a period of XX Number of Years XX from the date of original shipment. EXFO also warrants that this equipment will meet applicable specifications under normal use.
Warranty Liability Liability EXFO shall not be liable for damages resulting from the use of the product, nor shall be responsible for any failure in the performance of other items to which the product is connected or the operation of any system of which the product may be a part. EXFO shall not be liable for damages resulting from improper usage or unauthorized modification of the product, its accompanying accessories and software.
Warranty Exclusions Exclusions EXFO reserves the right to make changes in the design or construction of any of its products at any time without incurring obligation to make any changes whatsoever on units purchased. Accessories, including but not limited to fuses, pilot lamps, batteries and universal interfaces (EUI) used with EXFO products are not covered by this warranty.
Warranty Service and Repairs Service and Repairs EXFO commits to providing product service and repair for five years following the date of purchase. To send any equipment for service or repair: 1. Call one of EXFO’s authorized service centers (see EXFO Service Centers Worldwide on page 43). Support personnel will determine if the equipment requires service, repair, or calibration. 2.
Warranty EXFO Service Centers Worldwide EXFO Service Centers Worldwide If your product requires servicing, contact your nearest authorized service center. EXFO Headquarters Service Center 400 Godin Avenue Quebec (Quebec) G1M 2K2 CANADA EXFO Europe Service Center Winchester House, School Lane Chandlers Ford, Hampshire S053 4DG ENGLAND EXFO Telecom Equipment (Shenzhen) Ltd. 3rd Floor, Building 10, Yu Sheng Industrial Park (Gu Shu Crossing), No.
A Technical Specifications IMPORTANT The following technical specifications can change without notice. The information presented in this section is provided as a reference only. To obtain this product’s most recent technical specifications, visit the EXFO Web site at www.exfo.com.
Technical Specifications W2CM 10 Gigabit Ethernet Interface Series W2CM 10 Gigabit Ethernet Interface Series Test solution LTE eNodeB, P-GW, S-GW, MME SBC, security gateways, BGF, IMS I/P/C-CSCF, HSS, SIP proxy/registrar Protocol supported HTTP, SMTP,POP,RTSP, GTP-c, GTP-u, S1-AP, S1-MME, NAS, SIP, Diameter, Megaco/H.248, RTP/RTCP, SRTP/SRTCP, TLS, IPSec, IKEv1, IKEv2, IPv4, IPv6, TCP, UDP, SCTP, DHCP, DNS CODEC support AMR, ILBC, G.711, G.729, G.721, G.722, G.726, G.723, G.
Index Index A AC requirements ......................................... 21 after-sales service ........................................ 37 C caution of personal hazard................................. 16 of product hazard.................................. 16 certification information ................................v cleaning front panel............................................. 33 conventions, safety ..................................... 16 current, electrical ........................................
Index W warranty certification ........................................... 41 exclusions .............................................. 41 general .................................................. 39 liability................................................... 40 null and void..........................................
MARKING REQUIREMENTS NOTICE NOTICE 㪖㽷尐㻑抩⛙ 抩⛙ CHINESE CHINESEREGULATION REGULATIONON ONRESTRICTION RESTRICTIONOF OFHAZARDOUS HAZARDOUSSUBSTANCES SUBSTANCES Product Environmental protection use period (years) Logo ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ ℶ❐ AND 䘾⬒≬㔳∎䞷㦮棟 () 㪖㉦ NAMES NAMES ANDCONTENTS CONTENTSOF OFTHE THETOXIC TOXICOR ORHAZARDOUS HAZARDOUS SUBSTANCES SUBSTANCES OR ORELEMENTS ELEMENTS CONTAINED CONTAINEDIN INTHIS THISEXFO EXFOPRODUCT PRODUCT ▔⚺⦷㦻 ▔⚺⦷㦻EXFO EXFOℶ❐₼䤓㦘㹡㦘⹂䓸德㒥⏒侯䤓⚜䱿✛⚺摞 ℶ❐₼䤓㦘㹡㦘⹂䓸德㒥⏒侯䤓⚜䱿✛⚺摞 his Exfo
MARKING REQUIREMENTS 㪖㽷尐㻑 Product Environmental protection use period (years) Logo ℶ❐ 䘾⬒≬㔳∎䞷㦮棟 ( ) 㪖㉦ This Exfo product 㦻 EXFO ℶ❐ Batterya 䟄㻯 a a. If applicable.
P/N: 1063196 www.EXFO.com · info@exfo.com CORPORATE HEADQUARTERS 400 Godin Avenue Quebec (Quebec) G1M 2K2 CANADA Tel.: 1 418 683-0211 · Fax: 1 418 683-2170 EXFO AMERICA 3400 Waterview Parkway Suite 100 Richardson, TX 75080 USA Tel.: 1 972-761-927 · Fax: 1 972-761-9067 EXFO EUROPE Winchester House, School Lane Chandlers Ford, Hampshire S053 4DG ENGLAND Tel.: +44 2380 246 800 · Fax: +44 2380 246 801 EXFO ASIA-PACIFIC 100 Beach Road, #25-01/03 Shaw Tower SINGAPORE 189702 Tel.
