User's Manual

ManualsBrandsExcel Engineering ManualsElectronicsMotion Detector

MAINTENANCE

Test your SafePresence Motion Detector and all components daily and before each use. Inspect the unit for

damage regularly. Replace any damaged or worn components immediately. Contact your distributor if the

Motion Detector needs repair. Do not disassemble or alter the product.

CLEANING

1. Clean the SafePresence Motion Detector with a damp (not wet) rag using non-caustic cleaning agents.

2. Never immerse the system or pager in any liquids.

STORAGE

1. Store the SafePresence Motion Detector in a safe place and in an area free from high humidity and temperature.

TROUBLESHOOTING

Contact your distributor if the Motion Detector needs repair. Do not disassemble or alter the product.

If you are experiencing problems with your SafePresence Motion Detector, refer to this Troubleshooting Guide.

If you need additional assistance, contact your distributor.

SAFEPRESENCE MOTION DETECTOR

Problem Cause Solution

LED Light does not light up.

No alert sounds on sensor or chime.

Volume too low

Low battery.

Object not in range of sensor.

Interference.

Low battery.

Pager speaker covered.

Replace battery.

Adjust sensor angle or location.

Move pager within range of sensor.

Move sensor/pager and test.

Replace battery.

Uncover/move pager.

Turn volume from Low to High.

For assistance call your distributor or visit www.safepresence.com

SafePresence™ is a trademark of J. Brasch Co. or its afﬁ liates.

READ and follow these instructions. SAVE them for future use.

IMPORTANT SAFETY INSTRUCTIONS

Read these important instructions THOROUGHLY before using the SafePresence Motion Detector.

When using the SafePresence Motion Sensor, instructions, particularly warnings and cautions should always

be followed. Failure to read and follow these instructions, warnings and cautions may result in damage to the

product, ﬁ re, electric shock, or personal injury or death.

Test the Motion Detector daily and before each use.

1. Read all instructions.

2. Follow all warnings and instructions including those marked on the product(s).

3. The Motion Detector is only an aid for caregivers and is not designed to replace proper nursing care including,

but not limited to 1) visual monitoring 2) direct patient supervision 3) proper training for all caregivers using the

system 4) testing the system daily and before each use, and 5) immediate caregiver response to the alerts.

The SafePresence Motion Detector and accessories may not be suitable for all individuals.

GENERAL

1. Train each caregiver that uses the Motion Detector system. Keep a record of all training.

2. Keep the Motion Detector system dry and away from water or other liquids at all times. The Motion Detector system

is not water resistant and operation may be affected by liquids and high humidity.

3. Contact your distributor if the SafePresence Motion Detector needs repair. Do not disassemble or alter the product.

4. Mount sensor in locations where there is minimal risk of tampering.

BATTERY SAFETY

1. Only use 9V alkaline batteries in sensor and pager.

2. Check low battery alerts on sensor and pager continuously. When LED lights start ﬂ ashing, discontinue use and

replace batteries immediately.

3. Remove batteries when not using the device for an extended period of time.

4. Keep batteries dry.

5. Children should not handle batteries unless supervised by an adult.

6. If batteries leak, discontinue use. Remove batteries. Clean and wipe off battery case and contact your distributor.

7. Test the sensor and pager when batteries are replaced.

DEVICE DISPOSAL

1. Dispose of batteries properly and in accordance with applicable local laws. Do not burn batteries. They may explode.

2. Recycle electrical products. Check with your local authority for recycling information. Do not dispose electrical

products with household waste.

OPERATING AND STORAGE

1. Use Motion Detector system in areas not subject to dust, high humidity, and high temperatures.

2. Avoid placing sensor and pager in direct sunlight.

3. Keep open ﬂ ame sources, such as lighted candles, off sensor and pager.

4. Wipe the outer surface of the Motion Detector sensor and pager with a soft, damp – not wet – cloth.

Do not use benzene, thinner, or any abrasive powder for cleaning the system.

5. Operating and storage: 0º to 50º C.

For assistance call your distributor or visit www.safepresence.com

SafePresence™ is a trademark of J. Brasch Co. or its afﬁ liates.

READ and follow these instructions. SAVE them for future use.