User Manual

EXCEL DRYER, INC 1.800.255.9235 EXCELDRYER.COM [e-mail]
357 CHESTNUT STREET, EAST LONGMEADOW, MA 01028
1/2017
3
READ AND SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer.
B. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
CLEANING / MAINTENANCE
OUTSIDE GentlywashCover(includingairinletholes)usingasoftclothorspongeandamildsoapordetergentwith
lukewarmwatertoloosendirtandgrime.
INSIDE Excelrecommendsinspectingtheinsideofthedryerandcleaningasrequiredatleastonceperyear,orif
 performancediminishes.Heavierusage,oranenvironmentthatcontainsexcessivelint,dustorotherparticles,
 requiresmorefrequentcleaning.Lintontheairinlet,thePre-Filters(DryerorHEPAifsoequipped),orother
 internalpartsofdryerwillreduceefciencyandshortenthelifeoftheworkingparts.
 Toclean,shutoffpowertodryeratserviceconnection.RemoveCoverbyunscrewingthe2Tamper-ProofBolts
 fromsideofCoverwiththespecialTamper-ProofWrenchprovidedwitheachdryer.Useasmall,softbrushto
 gentlycleanallparts.IfyourunitcontainsadryerPre-lterorHEPAFiltrationSystem,unclipthePre-Filter,rinse
 thePre-Filterwithwateranddry.Re-install. DO NOT CLEAN THE HEPA FILTER OR ALLOW IT TO COME INTO
CONTACT WITH WATER.
TROUBLESHOOTING
SIDEVIEW
FRONTVIEW
FACINGWALL
Dryer does not turn on
1. Checkpowertotheunitandconnections.Verifydryerisreceivingvoltageat
TerminalBlock.
2. CheckREDserviceLEDlightnexttoairoutletonbottomofdryerfor
Light is ON–PlacehandsunderSensor.Iflightstayson,thenreplaceSensor.
 Iflightgoesoff,checktomakesurewiringiscorrect.IfOK,checkwire
 connectingtoMotor.IfbothareOK,replaceMotor.
Light is OFF–Checkforloose,disconnectedorimproperwiring(Seewiring
 schematicinsidedryerCover),orreplaceControlAssembly.
Light is FLASHING–SeeerrorcodesinCODEchart
SENSOR RANGE ADJUSTMENT: If dryer will not turn on, stays on, or stops
working, it may be mounted too close to a counter or object and has gone into
lockout. If relocating appliance is not possible, adjust the range of the Sensor.
Turn off power to dryer then turn the range adjustment on the Control Assembly
counterclockwise towards L (-) low to decrease Sensor range.
Dryer does not shut off
1. May be mounted too close to a counter or object (adjust Sensor range).
2. Checkforloose,disconnectedorimproperwiringatControlAssembly(referto
wiringschematicafxedtoblowerhousing).
3. ReplaceControlAssembly.
Dryer does not always turn on, or turns on by itself
1. May be mounted too close to counter or object (adjust Sensor range).
2. CheckforforeignmaterialonOpticalSensornexttoAirOutlet.
3. CheckforloosewiresonControlAssembly.
4. ReplaceControlAssembly.
READ AND SAVE THESE INSTRUCTIONS