REVERSE OSMOSIS DRINKING WATER SYSTEMS Model: EWR 5075 INSTALLATION, OPERATION & SERVICE MANUAL Barrie, Ontario Canada www.excaliburwater.
TABLE OF CONTENTS Page INTRODUCTION TO THE REVERSE OSMOSIS DRINKING WATER SYSTEM . 1 PREPARATION A. Major System Components for the Reverse Osmosis Drinking Water System Installation Drawings for the Reverse Osmosis Drinking Water Systems B. Tools Recommended for Reverse Osmosis Drinking Water Installation C. Site Selection For Reverse Osmosis Major System Components 2 3 4 4 REVERSE OSMOSIS INSTALLATION STEPS A. Reverse Osmosis Faucet Installation Reverse Osmosis Faucet Drawing B.
INTRODUCTION Your new Reverse Osmosis Drinking Water System uses a combination of filtration technologies to reduce unwanted contaminants in your water supply. Your Reverse Osmosis System uses the following steps combine to give you the best in clear sparkling Reverse Osmosis water: The Reverse Osmosis membrane is a specially constructed, fully aromatic polyamide film, and is classified as a Thin Film Composite (T.F.C.).
REVERSE OSMOSIS PREPARATION A. Reverse Osmosis Components The following components comprise the Reverse Osmosis Drinking Water System. (Refer to Fig. 1, below for general system layout.) 9. Reverse Osmosis Sediment Pre-filter, shrink wrapped. 10.Reverse Osmosis activated Carbon Prefilter, shrink wrapped. 11.Reverse Osmosis In-Line Activated Coconut Shell Carbon Post Filter. 12.
BALL 3
B. Tools Recommended for Reverse Osmosis Installation C. Site Selection for Major System Reverse Osmosis Components The following tools will cover most of the Reverse Osmosis installation sites encountered: The Reverse Osmosis System was designed to fit under a sink, however, because of space limitations or other reasons, the Reverse Osmosis system's flexible design allows for other locations.
4. Reverse Osmosis Feed Water Connection – The Reverse Osmosis Feed Water Saddle Valve should be located as close to the manifold assembly as possible. USE A POTABLE COLD WATER SUPPLY ONLY TO YOUR REVERSE OSMOSIS SYSTEM. Softened water is preferred as it will extend the life of the Reverse Osmosis Membrane. 2b. Drilling a porcelain sink: It is best to use a special 5/8" diameter cutter designed for porcelain. A carbide tipped masonry bit is a second choice.
B. Reverse Osmosis Feed Water Ball Valve Installation 3. With the Reverse Osmosis Feed Water Ball Valve closed, open the Reverse Osmosis sink faucet and the water supply and allow the water to run for a few minutes to flush any debris caused by the installation. Decide on location. Do NOT connect Reverse Osmosis to a hot water feed line. Water over 100ºF may cause permanent damage to the Reverse Osmosis Membrane. (Refer to Fig. 3 page 8.) 1.
C. Reverse Osmosis Drain Clamp Installation 3. Locate the 3/8" Drain Tubing connected to the Reverse Osmosis System. Route to the Reverse Osmosis tubing to the Drain Clamp and trim to length. Choose the Reverse Osmosis drain outlet location. The following are instructions for discharging in the sink drain pipe. (Refer to Fig. 1, page 3) CAUTION: The lowest point of the line should be the point of connection to the Reverse Osmosis Drain Clamp.
Slowly open the Reverse Osmosis Feed Water Saddle Valve (turning counter clockwise). D. Position the Reverse Osmosis Holding Tank & Make the Final Hose Connections 1. Check the Reverse Osmosis tank precharge pressure. Make sure it is between 5 to 7 psig. As soon as the water begins to come out of the Reverse Osmosis Dispensing Faucet, close the Faucet. 2. Pull the cap/plug off the top of the Reverse Osmosis tank where the Reverse Osmosis Tank Shut-Off should go. (Refer to Fig.
REVERSE OSMOSIS OPERATION & MAINTENANCE 1. Close the Reverse Osmosis Feed Water Ball Valve by turning fully clockwise and open the Reverse Osmosis Dispensing Faucet by lifting the handle. Allow the Reverse Osmosis Holding Tank to empty. A. Reverse Osmosis Normal Operation 1. Reverse Osmosis systems produce drinking water at relatively slow rates. Normal operation is to let the Reverse Osmosis Holding Tank fill with water and then draw water as is needed.
3 ml) into the Reverse Osmosis tubing and reconnect it to the Tee. 5. Slowly open the Reverse Osmosis Feed Water Saddle Valve. NOTE: Now is the convenient time to change the In-Line Reverse Osmosis Activated Carbon Post Filter. 6. When water begins dripping out of the Reverse Osmosis Faucet, in the following order, close the Reverse Osmosis Faucet and open the Reverse Osmosis Holding Tank Valve.
REVERSE OSMOSIS TROUBLE SHOOTING GUIDE Problem Low quantity of Reverse Osmosis Product Water from Holding Tank Possible Cause Reverse Osmosis Feed Water Ball Valve is plugged or closed. Clogged Sediment Pre-filter or Activated Carbon Pre-filter. Low water pressure. Reverse Osmosis. Membrane is fouled. Plugged In-Line Activated Carbon Post Filter. Air pre-charge pressure in Holding Tank is too high.
Problem High Total Dissolved Solids (TDS) in the Product Water (continued) Possible Cause The Product Water and Drain Water lines are reversed. No drain flow, Reverse Osmosis Drain Restrictor is clogged. The Reverse Osmosis ASO Valve is not closing. New In-Line or Activated Carbon Pre-filter not rinsed completely. The Reverse Osmosis Feed Water TDS has increased. Tastes and odors in the Reverse Osmosis Product Water The In-Line or Activated Carbon Pre-filter is exhausted.
5 YEAR WARRANTY REVERSE OSMOSIS SYSTEM Thank you for your purchase of our Reverse Osmosis System. For proof of purchase, please retain your Invoice/Sales Order Copy. Warranty ~ Offered Excalibur Water Systems warranties its products to be free from defect in materials and workmanship to the original owner from the date on the proof of purchase as described below.
