Installation Manual
Table Of Contents
- ExtendAir eMIMO Series Digital Microwave Radios Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- About this Document
- Introduction
- Pre-installation Tasks
- Link Engineering and Site Planning
- Familiarization with the ExtendAir eMIMO Series Radios
- Initial Configuration and Back-to-Back Bench Test
- Time Division Duplex (TDD) Factors
- Link Orientation and Synchronization (future feature)
- Radio Synchronization (future feature)
- Offset Timing
- Virtual Local Area Network (VLAN)
- Simple Network Management Protocol (SNMP) (future feature)
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Telnet into the Command Line Interface (CLI) (future feature)
- Telnet
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- File Management Page
- System Configuration Page
- VLAN Settings Page
- Antenna Alignment Page
- Performance Page
- Metrics – Link Statistics and Radio Interface Statistics Page
- Reboot Page
- Manual Page
- Specifications
- Interface Connections
- Antennas
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Safety Notices
- Regulatory Notices
- Regulatory Compliance–TBD
- EIRP Limits for the United States and Canada
- EIRP Limits for Australia
- EIRP Limits for the European Union and ITU Countries
- Declaration of Conformity to the R&TTE Directive 1999/5/EC
- Exalt Limited Hardware Warranty Software License and RMA Procedures Agreement
- Copyright Notices
- Index
Exalt Installation and Management Guide
ExtendAir eMIMO Series Digital Microwave Radios
208363-001 76
2013-05-01
This device must be professionally installed.
To comply with regulations, the output power of this device may need to be adjusted in accordance to
the associated transmission system. See RF Output Power Setting
for details.
The antenna associated with this device shall be mounted in a location that is at least 10.5'/3.2m away
from humans that may be subject to long-term or continuous exposure.
Canada Compliance
When operating in the 4940–4990 MHz band, the ExtendAir eMIMO models (regulatory model name/
number eMIMO 100) are licensed-band products operating within RSS-111 of Industry Canada
regulations. This band is specifically reserved for Public Safety applications and related agencies, in
accordance with these regulations.
Transmitter power reduction may be required, depending on transmission system gains and losses, in
accordance with instructions found in this appendix.
When operating in the 5250-5850MHz bands, the ExtendAir eMIMO models (regulatory model name/
number eMIMO 100) operate under RSS-210 of Industry Canada regulations. Operation is subject to
the following conditions, unless express permission is granted by Industry Canada to operate in a
different manner:
• External amplifiers cannot be used to boost the power or to overcome transmission system losses,
unless the specific amplifier/cable/antenna combination is expressly authorized by Industry
Canada.
• Cross-border transmissions are expressly prohibited, except with written permission from both
Industry Canada and the governing body of the neighboring country (FCC for USA)
• Only parabolic dish antennas, directional flat-panel, or omni-directional antennas may be used. No
other types of antennas are authorized. Parabolic dishes of either grid or solid type are allowed.
• Antenna gains between 9dBi and 37.9dBi are permitted.
Industry Canada (IC), Canada
This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du
Canada.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two
conditions:
1 this device may not cause interference, and
2 this device must accept any interference, including interference that may cause undesired
operation of the device.
Antennas Supported in Canada
The ExtendAir eMIMO models (regulatory model name/number eMIMO 100) are designed to operate
with the antennas listed in Table 7
and Table 6, which have a maximum gain of 37.9dBi. Antennas not
included in the list or having a gain greater than 37.9dBi are strictly prohibited for use with this device.
The required antenna impedance is 50 Ohms.