User's Manual
Table Of Contents
- EX-i Series GigE (FDD)
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- Telnet into the Command Line Interface (CLI)
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- NTP and Time Zone Configurations
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- System Configuration Page
- Allocation Page
- Ethernet Interface Configuration Page
- T1/E1 Configuration Pages
- MHS Configuration Page
- VLAN Configuration Page
- Ethernet Rate Limiting Page
- Ethernet Learning Page
- Syslog Configuration Page
- Ethernet Aggregation
- Cross Connect (X Connect) Page
- Alarms Page
- MHS Status Page
- Performance Page
- ATPC Statistics Page
- Event Log Page
- User Throughput Page
- Diagnostic Charts Page
- Ethernet Utilization Page
- PA Control Page
- Spectrum Analyzer
- Reboot Page
- Manual Page
- Specifications
- Interface Connections
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- EIRP Limits for the United States and Canada
- Licensing 6 and 11GHz Models
- Antennas 5GHz Models
- Copyright Notices
- END USER AGREEMENT
- Index
Exalt Installation and Management Guide
EX-i Series GigE (FDD) Digital Microwave Radios
8 202675-008
2016-06-01
through Telnet/CLI) to match the installed diplexer configuration. Additional information on this
configuration can be found in Rear Panel Diplexer Orientation and
System Configuration Page.
Exalt recommends using the Exalt GUI for radio configuration. This interface requires a computer
with an Ethernet port and web browser software, such as Microsoft Internet Explorer 5.0 or above. See
Configuration and Management for details on how to connect to and use the browser-based GUI
interface.
Shipping Box Contents
The radios are shipped as single terminals. Two terminals make up a hop, or link pair. An outer box
has labeling that indicates the contents of the box, with the part number and serial number details for
the radio terminals. The terminal box contains the following items:
• Radio terminal
• Accessory kit
– Rack mount brackets
– Bracket mounting hardware (8 x M4 screws; 8 x M4 wave washers)
– DC power connectors (2)
– Grounding hardware (1 x M5 screw; 1 x M5 wave washer; 2 x M5 flat washers)
• Registration card
• Quick-start guide
Each terminal requires a diplexer filter kit (sold separately) to operate. The diplexer filter kit contains
the following items:
• Semi-rigid SMA cables for connecting the diplexer filter to the radio terminal
• Mounting hardware
• One 18" flexible SMA-to-N (F) cable for connection to a waveguide adapter (if applicable)
Exalt also sells the following item(s) separately:
• N-to-CPR-137 waveguide flange adapters to connect to the primary waveguide (6GHz)
• N-to-CPR-90 waveguide flange adapters to connect to the primary waveguide (11GHz)
• Additional diplexers for redundant and other applications.
Inspect the outer packaging and the contents of the boxes upon receipt. If you suspect any shipping
damage or issues with the contents, contact Exalt Customer Care (see
Introduction).
Initial Configuration and Back-to-Back Bench Test
Every Exalt digital microwave radio goes through extensive quality testing and performance
evaluation over the full operating temperature range prior to shipment. However, before installation, it
is strongly advised to perform several tests and tasks that are much more difficult to perform once the
Note: Register your system as soon as possible. A 2-year Warranty period applies to
products registered within 90 days of purchase. The Warranty period is reduced to 1-year for
unregistered products and products registered after the first 90 days. See
END USER
AGREEMENT.