User's Manual
Table Of Contents
- EX-i Series GigE (FDD)
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- Telnet into the Command Line Interface (CLI)
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- NTP and Time Zone Configurations
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- System Configuration Page
- Allocation Page
- Ethernet Interface Configuration Page
- T1/E1 Configuration Pages
- MHS Configuration Page
- VLAN Configuration Page
- Ethernet Rate Limiting Page
- Ethernet Learning Page
- Syslog Configuration Page
- Ethernet Aggregation
- Cross Connect (X Connect) Page
- Alarms Page
- MHS Status Page
- Performance Page
- ATPC Statistics Page
- Event Log Page
- User Throughput Page
- Diagnostic Charts Page
- Ethernet Utilization Page
- PA Control Page
- Spectrum Analyzer
- Reboot Page
- Manual Page
- Specifications
- Interface Connections
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- EIRP Limits for the United States and Canada
- Licensing 6 and 11GHz Models
- Antennas 5GHz Models
- Copyright Notices
- END USER AGREEMENT
- Index
Exalt Installation and Management Guide
EX-i Series GigE (FDD)
202675-008 125
2016-06-01
Index
A
Adaptive Coded Modulation (ACM) parame-
ter 48
Administration Settings page 37
administrator privileges 32
Advance Encryption Standard 38
AES 38
AIS enabling/disabling 54
alarm conditions 35
Alarm connector 96
alarms 68, 76, 93
clearing 76
Ethernet 69
Link 68
T1/E1 Input 69
Temperature 69
Alarms page 68
AMI 54
antennas
alignment 28, 102
mounting 25
indoor 27
mounting height 7
polarization orientation 7
site preparation considerations 7
system grounding 7
transmission line 26
troubleshooting 102
B
B8ZS 54
back-to-back bench test 9, 104
back-to-back bench test configuration 104
bandwidth 7
Bandwidth parameter 45, 48
BER 79
browsers 31
C
cables
troubleshooting
improper RF cable termination 101
carrier-to-interference tolerance 7
CLI 30
menu options 31
root menu 30
connectors
Alarm 96
CONSOLE 97
DC 24
DC Power 98
Ethernet 95
front panel 16
T1/E1 94
Console connector 97
console interface 93
Current BER field 72
Current RSL field 73
D
date and time 37
DC connector 24
DC coupler 29
DC Power connector 98
DC power source 23
Diagnostic Charts page 79
dimensions 88
diplexer filter kit 8
diplexer orientation 20
diplexers 20
antenna connection 22
non-standard 21
waveguide and 22
E
E1 channels 55
effective isotropic radiated power (EIRP) 10
Errored Seconds (ES) field 72
Ethernet 7
Ethernet configuration parameters 45
Ethernet connectors 95
Ethernet interface 92
Ethernet Interface Configuration page 52
Event Log page 76
ExaltCalc tool 100
external loopback modes 58
F
factory default settings 24, 44
fade margin 7, 102
File Activation page 46
files
activating stored 46
default configuration file 44
G
gateway (default) 44
grounding 102