User's Manual
Table Of Contents
- EX-r Series GigE
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- Link Engineering and Site Planning
- Familiarization with the EX-r Series GigE Radios
- Initial Configuration and Back-to-Back Bench Test
- Time Division Duplex (TDD) Factors
- Link Orientation and Synchronization
- Radio A/B Configuration
- Radio Synchronization
- Offset Timing
- Virtual Local Area Network (VLAN)
- Simple Network Management Protocol (SNMP)
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Telnet into the Command Line Interface (CLI)
- Telnet
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- System Configuration Page
- Ethernet Interface Configuration Page
- VLAN Configuration Page
- T1/E1 Configuration Pages
- GPS Information Page
- Alarms Page
- Performance Page
- Event Log Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Reboot Page
- Manual Page
- Specifications
- 201872-003Interface Connections
- Antennas
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Dynamic Frequency Selection
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- Regulatory Domain Keys
- EIRP Limits for the United States and Canada
- EIRP Limits for Australia
- EIRP Limits for the European Union and ITU Countries
- Declaration of Conformity to the R&TTE Directive 1999/5/EC
- Copyright Notices
- END USER AGREEMENT
- Index
Exalt Installation and Management Guide
EX-r Series GigE Digital Microwave Radios
viii 201872-003
2015-10-23
About this Document
This manual provides a complete description of the EX-r Series GigE Digital Microwave Radios and
related software. This manual provides planners, engineers, installers, system administrators, and
technicians general and specific information related to the planning, installation, operation,
management, and maintenance of these devices.
Revision History
Icons
The following icons denote specific types of information:
Date Products and Release code--
2006-09-19 EX-5r & EX-5r-c v.1.0.0
2007-02-19 EX-4.9r v1.0
2007-02-23 EX-5r and EX-5r-c v.2.0.0 (GPS, Sync, SNMP feature release)
2007-04-20 EX-4.9r v.1.1 (AES feature release)
2007-07-27 EX-5r IP and EX-5r-c IP v 2.1.0
EX-5r and EX-5r-c v.2.1.0 (Regulatory Domain Key, Base License Key, and Dynamic Frequency
Selection feature releases)
2007-10-26 EX-5r, EX-5r-c, EX-5r-c IP v3.0 (Spectrum Analyzer, VLAN, Asymmetry, Legacy SNMP and Enhanced
Event Log feature releases)
2008-03-08 New chassis release
2008-05-23 EX-5r GigE & EX-5r-c GigE v1.0.0
2009-05-26 EX-4.5r/r-c GigE release. v1.0.0
2015-10-15 Updated to include current contact information.
Note: This symbol means take note. Notes contain helpful suggestions or references to
materials not contained in the manual.
Warning! This warning symbol means there is a risk of electric shock. This situation that
could cause bodily injury. Before working on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for preventing
accidents.
Caution! This symbol means be careful. There is a risk of doing something that might
result in equipment damage or loss of data. This is a general warning, caution, or risk of
danger.