User's Manual
Table Of Contents
- EX-r Series GigE
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- Link Engineering and Site Planning
- Familiarization with the EX-r Series GigE Radios
- Initial Configuration and Back-to-Back Bench Test
- Time Division Duplex (TDD) Factors
- Link Orientation and Synchronization
- Radio A/B Configuration
- Radio Synchronization
- Offset Timing
- Virtual Local Area Network (VLAN)
- Simple Network Management Protocol (SNMP)
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Telnet into the Command Line Interface (CLI)
- Telnet
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- System Configuration Page
- Ethernet Interface Configuration Page
- VLAN Configuration Page
- T1/E1 Configuration Pages
- GPS Information Page
- Alarms Page
- Performance Page
- Event Log Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Reboot Page
- Manual Page
- Specifications
- 201872-003Interface Connections
- Antennas
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Dynamic Frequency Selection
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- Regulatory Domain Keys
- EIRP Limits for the United States and Canada
- EIRP Limits for Australia
- EIRP Limits for the European Union and ITU Countries
- Declaration of Conformity to the R&TTE Directive 1999/5/EC
- Copyright Notices
- END USER AGREEMENT
- Index
Exalt Installation and Management Guide
EX-r Series GigE Digital Microwave Radios
201872-003 24
2015-10-23
LED Indicators
Table 3 provides details of the LED indicators on the EX-r Series GigE radios. Note that there are two
LEDs, labeled top and bottom, associated with each connector. See Alarms Page
for information on
how the Exalt GUI displays LED status.
RESET Button
There is only one external control on the EX-r Series GigE radios system, a button labeled “RESET”
located on the power injector. This button performs a critical system parameter reset.
Use the reset function if the IP address and/or passwords are lost. Use the following steps to perform a
critical parameter reset:
1 Remove power from the radio by disconnecting the AC adapter from the power injector.
2 Hold down RESET button on the power injector while applying power.
Hold the RESET button down through the whole power cycle and monitor the DATA+POWER
left LED on the power injector. Release the RESET button only after the LED is in the steady state
(approximately 2 minutes).
3 Release the RESET button.
The following configurations are reset on the radio:
• IP address = 10.0.0.1
Table 3 LED indicators
Location Type Function
TDM 2&4 Green LED Solid when T1 clocking is present for input #2.
TDM 2&4
Bottom
Green LED Solid when T1 clocking is present for input #4.
TDM 1&3 Green LED Solid when T1 clocking is present for input #1.
TDM 1&3
Bottom
Green LED Solid when T1 clocking is present for input #3.
Sync Out Green LED Solid when radio is configured as sync source.
Sync Out Bottom Green LED Solid when synch source is external (GPS).
Ethernet 2 Green LED (Future implementation.)
Ethernet 2
Bottom
Green LED (Future implementation.)
Sync In/RSL Green LED Solid when valid Sync In connection is detected.
Sync In/RSL
Bottom
Green LED Unused.
Power/Ethernet Green LED Solid when proper power is applied.
Power/Ethernet
Bottom
Green LED (Future implementation)
Power Injector
DATA+POWER
Left
Green LED Solid when no alarm conditions are present.
Flashing when in Reset mode.
DATA+POWER
Right
Green LED Solid when proper power is applied.