User's Manual
Table Of Contents
- EX-i Series (TDD)
- Digital Microwave Radios
- Installation and Management Guide
- Legal Notice
- Open-Source License Information
- Table of Contents
- List of Figures
- List of Tables
- About this Document
- Introduction
- Pre-installation Tasks
- Link Engineering and Site Planning
- Familiarization with the i-Series Radios
- Initial Configuration and Back-to-Back Bench Test
- RF Output Power Setting
- Time Division Duplex (TDD) Factors
- Link Orientation and Synchronization
- Radio Synchronization
- Offset Timing
- Virtual Local Area Network (VLAN)
- Link Symmetry
- Simple Network Management Protocol (SNMP)
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- Telnet into the Command Line Interface (CLI)
- Exalt Graphical User Interface (GUI)
- Quick Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- Simple Network Management Protocol (SNMP) Configuration
- File Transfer Page
- File Activation Page
- Access Security Page
- System Configuration Page
- MHS Configuration Page
- Ethernet Interface Configuration Page
- VLAN Configuration Page
- T1/E1 Configuration Pages
- DS3 Configuration Page
- GPS Information Page
- Alarms Page
- MHS Status Page
- Performance Page
- Event Log Page
- User Throughput Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Ethernet Utilization Page
- Reboot Page
- Manual Page
- Specifications
- Interface Connections
- DIP Switch Settings (-16 Models Only)
- Antennas
- DC Coupler for Antenna Alignment
- Troubleshooting
- Back-to-back Bench Testing
- General Compliance and Safety
- Dynamic Frequency Selection
- Safety Notices
- Regulatory Notices
- Regulatory Compliance
- Regulatory Domain Keys
- EIRP Limits for the United States and Canada
- EIRP Limits for the European Union and ITU Countries
- EIRP Limits for Australia
- Declaration of Conformity to the R&TTE Directive 1999/5/EC
- END USER AGREEMENT
- Copyright Notices
- Index
Exalt Installation and Management Guide
EX-i Series (TDD) Digital Microwave Radios
2 206501-019
2016-05-24
The following models of radios are covered in this manual:
• EX-2.4i, 10/100 Ethernet + 4xT1/E1
– Configured for 100Mbps + 4xT1/E1 (32MHz/Mode2)
– With license-key upgrade for 200Mbps capacity (64MHz/Mode2)
– With license-key upgrade for FIPS-197 compliant 128-bit or 256-bit AES encryption
• EX-2.4i Lite, 10/100 Ethernet + 4xT1/E1
– Configured for 27Mbps (8MHz/Mode2 and 16MHz/Mode1)
– With license-key upgrade for 55Mbps
– With license-key upgrade for 100Mbps
– With license-key upgrade for 2xT1/E1
– With license-key upgrade for 4xT1/E1
– With license-key upgrade for FIPS-197 compliant 128-bit or 256-bit AES encryption
• EX-2.4i-16 (or EX-2.4i-16 K, exclusively for Korea), 10/100 Ethernet + 16xT1/E1
– Configured for 4xT1/E1, 100Mbps (32MHz/Mode2)
– With license-key upgrade for 8xT1/E1, 100Mbps (32MHz/Mode2)
– With license-key upgrade for 12xT1/E1, 100Mbps (32MHz/Mode2)
– With license-key upgrade for 16xT1/E1, 200Mbps (64MHz/Mode2)
– With license-key upgrade for FIPS-197 compliant 128-bit or 256-bit AES encryption
• EX-4.9i, 10/100 Ethernet + 4xT1/E1
– Configured for 2xT1/E1, 27Mbps (10MHz/Mode2, 20MHz/Mode1)
– With license-key upgrade for 4xT1/E1, 55Mbps (20MHz/Mode2)
– With license-key upgrade for FIPS-197 compliant 128-bit or 256-bit AES encryption
• EX-5i, 10/100 Ethernet + 4xT1/E1
– Configured for 100Mbps (32MHz/Mode2)
– With license-key upgrade for 200Mbps capacity (64MHz/Mode2)
– With license-key upgrade for FIPS-197 compliant 128-bit or 256-bit AES encryption
• EX-5i Lite, 10/100 Ethernet + 4xT1/E1
– Configured for 27Mbps (8MHz/Mode2 and 16MHz/Mode1)
– With license-key upgrade for 55Mbps
– With license-key upgrade for 100Mbps
– With license-key upgrade for 2xT1/E1
– With license-key upgrade for 4xT1/E1
– With license-key upgrade for FIPS-197 compliant 128-bit or 256-bit AES encryption
• EX-5i-DS3 10/100 Ethernet + 1xDS3 + 16xT1/E1
– Configured for 100Mbps + 4xT1/E1 (32MHz/Mode2)