User's Manual

ManualsBrandsExalt Wireless ManualsElectronicsEX-5i Digital Microwave Radio

Table Of Contents

Legal Notice
Open-Source License Information
About this Document
- Revision History
- Icons
General Compliance and Safety
Regulatory Notices
- General
- Federal Communications Commission (FCC), United States
- Industry Canada (IC), Canada
  - Antennas Supported in Canada
- Europe/ITU (ETSI and CE Mark)
  - Declaration of Conformity to the R&TTE Directive 1999/5/EC
EU WEEE
EU RoHS
Regulatory Notices (4.9GHz Model)
Safety Notices
Exalt Limited Hardware Warranty
- Registration
- Exclusions
- RMA Procedures
Introduction
- Related Documentation and Software
- Basic Features
Pre-installation Tasks
- Link Engineering and Site Planning
- Familiarization with i-Series Radios
  - Shipping Box Contents
- Back-to-Back Bench Test and Configuration
- RF Output Power Setting
- Time Division Duplex (TDD) Factors
- Link Orientation and Synchronization
  - Radio A/B Configuration
    - Temporary Hardware Configuration Key (Standard Models Only)
    - DIP Switch Configuration (-16 Models Only)
- Radio Synchronization
System Installation and Initiation Process
- Record Keeping
Installation
- Mechanical Configuration and Mounting
  - Rack Mounting
  - Table or Rack Shelf Mounting the System
- Radio Ports and Indicators
- Power
- Antenna/Transmission System
- Antenna Alignment
Configuration and Management
- Command Line Interface (CLI)
  - Connect to the Radio with a Serial Connection
  - Connect to the Radio through a Telnet Connection
- CLI Screens and Menus
- Exalt Graphical User Interface (GUI)
  - Preparing to Connect
  - Make Connections
  - Log In
  - Login Privileges
- Quick-Start
- Navigating the GUI
  - Summary Status Section
  - Navigation Panel
- Radio Information Page
- Administration Settings Page
- System Configuration Page
- Ethernet Interface Configuration Page
- T1/E1 Configuration Pages
  - T1 Interface Configuration Page
  - E1 Interface Configuration Page
  - T1/E1 Loopback
- File Transfer Page
- File Activation Page
- Simple Network Management Protocol (SNMP) Configuration
- Alarms Page
- Performance Page
- Event Log Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Reboot Page
- Manual Page
Troubleshooting
- General Practices
- Typical Indications of Issues
- Improper RF Cable Termination
- Multipath Propagation
- RF Interference
- Path Obstruction
- Misaligned Antenna
- Faulty Antenna
- Improper Grounding
- Insufficient Link Margin
- Moisture in the Transmission System
- Physical Specifications
- Common System Specifications
- EX-2.4i System Specifications
- EX-4.9i System Specifications
- EX-5i System Specifications, 5.3 GHz Band
- EX-5i System Specifications, 5.4 GHz Band
- EX-5i System Specifications, 5.8 GHz Band
- Interfaces
  - RF
Back-to-back Bench Testing
- Basic Test
- Specification Performance Verification
DC Coupler for Antenna Alignment
- Required Items
- Interconnections
Interface Connections
- T1/E1 Connections
- Ethernet Connections
- Sync Connections
- Alarm Connector
- Console Connector
- DC Power Connector
DIP Switch Settings (-16 Models Only)
Copyright Notices
- Net-SNMP
Index

Exalt Communications, Inc.

Exalt i-Series Installation and Management Guide

5000001 84

2007-04-15

Figure 27 T1 Interface Configuration page (standard models)

E1 Interface Configuration Page

This page allows the administrator to enable/disable each individual E1 channel. The AIS

can also be enabled and disabled for each input. If enabled, the radio places an AIS code

on the output of the associated interface if and when the link fails or when there is no E1

signal available from the far end to provide the user at the local end. Loopback controls

are also provided (see T1/E1 Loopback on page 85).