User's Manual
Table Of Contents
- Legal Notice
- Open-Source License Information
- About this Document
- General Compliance and Safety
- Regulatory Notices
- EU WEEE
- EU RoHS
- Regulatory Notices (4.9GHz Model)
- Safety Notices
- Exalt Limited Hardware Warranty
- Introduction
- Pre-installation Tasks
- System Installation and Initiation Process
- Installation
- Configuration and Management
- Command Line Interface (CLI)
- CLI Screens and Menus
- Exalt Graphical User Interface (GUI)
- Quick-Start
- Navigating the GUI
- Radio Information Page
- Administration Settings Page
- System Configuration Page
- Ethernet Interface Configuration Page
- T1/E1 Configuration Pages
- File Transfer Page
- File Activation Page
- Simple Network Management Protocol (SNMP) Configuration
- Alarms Page
- Performance Page
- Event Log Page
- Diagnostic Charts Page
- Spectrum Analyzer Page
- Reboot Page
- Manual Page
- Troubleshooting
- General Practices
- Typical Indications of Issues
- Improper RF Cable Termination
- Multipath Propagation
- RF Interference
- Path Obstruction
- Misaligned Antenna
- Faulty Antenna
- Improper Grounding
- Insufficient Link Margin
- Moisture in the Transmission System
- Physical Specifications
- Common System Specifications
- EX-2.4i System Specifications
- EX-4.9i System Specifications
- EX-5i System Specifications, 5.3 GHz Band
- EX-5i System Specifications, 5.4 GHz Band
- EX-5i System Specifications, 5.8 GHz Band
- Interfaces
- Back-to-back Bench Testing
- DC Coupler for Antenna Alignment
- Interface Connections
- DIP Switch Settings (-16 Models Only)
- Copyright Notices
- Index
Exalt Communications, Inc.
Exalt i-Series Installation and Management Guide
5000001 6
2007-04-15
Industry Canada (IC), Canada
This device complies with RSS-210 of Industry Canada. Operation is subject to the
following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause
undesired operation of the device.
Antennas Supported in Canada
The EX-2.4i is designed to operate with the antennas listed in Table 1, which have a
maximum gain of 30.3dBi. Antennas not included in the list or having a gain greater than
30.3dBi are strictly prohibited for use with this device. The required antenna impedance
is 50 Ohms.
Table 1 EX-2.4i supported antennas
Manufacturer Model # Descri
p
tion Gain
(
dBi
)
Andrew 19T-2440-1 16-inch Solid Parabolic Dish 19
Andrew 21T-2441-1 24-inch Solid Parabolic Dish 21
Andrew 18T-2400-1 Semi-parabolic Grid 17
Andrew 26T-2400-1 Semi-parabolic Grid 23
Andrew P2F-23 2-foot Solid Parabolic Dish 21.6
Andrew P4F-23 4-foo
t
Solid Parabolic Dish 27.3
Andrew KP3F-23 3-foot Grid Parabolic Dish 25.1
Andrew KP4F-23 4-foot Grid Parabolic Dish 27.5
Andrew KPR3F-23 2-foot Grid Parabolic Dish 23.6
Andrew KPR4F-23 4-foot Grid Parabolic Dish 27.3
Andrew QD-2402 11-inch Panel 16
Gabriel DFPS.5-23 6-inch Panel 10.3
Gabriel DFPS1-23 1-foot Panel 16.5
Gabriel P-24A36 3-foot Grid Parabolic Dish 25.7
Gabriel P-24A48 4-foot Grid Parabolic Dish 27.7
Gabriel SSP2-23 2-foot Solid Parabolic Dish 20.7
Gabriel SSP4-23 4-foot Solid Parabolic Dish 26.7
Gabriel SSP6-23 6-foot Solid Parabolic Dish 30.3
Gabriel HSSP2-23 2-foot Solid HP Parabolic Dish 20.5
Gabriel HSSP4-23 4-foot Solid HP Parabolic Dish 26.3
Gabriel HSSP6-23 6-foot Solid HP Parabolic Dish 30.0
RadioWaves SP1-2.4 1-foot Solid Parabolic Dish 14
RadioWaves SP2-2.4 2-foot Solid Parabolic Dish 21.3
RadioWaves SP3-2.4 3-foot Solid Parabolic Dish 24.3
RadioWaves SP4-2.4 4-foot Solid Parabolic Dish 27.2
RadioWaves SP6-2.4 6-foot Solid Parabolic Dish 30.3
RadioWaves G3-2.4 3-foot Grid Parabolic Dish 24.5