Technical data

ManualsBrandseXact ManualsPower ToolPipeCut 360 system

Information

english

Exact PipeCut 360 System

Users manual

Guarantee of conformity with EU

requirements

We Exact Tools Oy, Mechelininkatu 15, 00100 Helsinki, Finland, guarantee

that the Exact PipeCut 360 Serial numbers 00000-99999 to which this

statement refers fulfills the basic health and safety requirements mentioned

in the (machine directive) EU directive 98/37/EY. Also the Exact PipeCut

360 fulfills the requirements of standard EN 60745-1:2003 + A1:2003

safety of hand-held electric motor operated tools and the applicable

parts of standard EN 60745-2-5 particular requirements for circular saws

and circular knives.

Also the Exact PipeCut 360 complies with the essential protection

requirements of the Council Directive 89/336/EEC as stated in the Article

4 and the tested product is in compliance with the following Product

Family standards: EN 55014-1 (2000), EN 55014-2 (1997), EN 61000-

3-3 (1995) + Am. A1 (2001)

Helsinki 30.06.2006

Seppo Makkonen

Managing Director

english

Summary of content (12 pages)

PAGE 1
Information english Exact PipeCut 360 System Users manual Guarantee of conformity with EU requirements We Exact Tools Oy, Mechelininkatu 15, 00100 Helsinki, Finland, guarantee that the Exact PipeCut 360 Serial numbers 00000-99999 to which this statement refers fulfills the basic health and safety requirements mentioned in the (machine directive) EU directive 98/37/EY.
PAGE 2
Contents Contents List of contents 1. Guarantee of conformity with EU requirements Foreword 3. Technical data 3. Electrical safety 4. Package contents Safety 5. Safety instructions 6. Use and limitations Operation 7. 8. 8. 8. 9. 9. 10. 10. 10.
PAGE 3
Foreword Kuva A Operating, safety, and servicing instructions Please read this operating, safety, and servicing instructions carefully before using the pipe saw. Also store this instruction book somewhere accessible to everyone using the pipe saw. In addition to these instructions, always follow the official work, health and safety regulations. The Exact PipeCut 360 is meant for professional use only.
PAGE 4
Foreword Exact PipeCut 360 pipecutting system, Package contents: Please check the package contains the following items: Pipesaw case Exact PipeCut 360 pipe saw Hard-metal blade 140 x 62 / Z 46 (fitted on the machine) Cutting holder and supporting holders x2 Hex socket key 2x (5 mm & 2 mm) Operating instructions 4
PAGE 5
Safety it cannot close in on the sawn gap and clamp onto the blade. The machine works at its best and safest when it is used the way for which it was designed. Safety Instructions In order to prevent, electrical shocks, injuries, and the risk of fire the following basic safety instructions should be followed. Dress suitably Do not use clothing that is too loose or jewellery when using the pipe saw as they could get caught on moving parts of the machine.
PAGE 6
Safety Extension cables outside When you work outdoors, always use an extension cable that is made and approved for outdoor use. Intended use and limitations The Exact PipeCut 360 pipe saw is intended for use as a pipe fitter’s tool at the installation site. The Exact PipeCut 200 pipe saw can only be used to cut round pipes, with a diameter of 75 to 360 mm and a maximum wall thickness of 8mm with steel and 12mm with plastics.
PAGE 7
Operation Fig. A 1.UNLOCK button 2.Power switch 3.Power-switch locking lever 4.Blade-guard cover 5.Blade-guard finger screw 6.Moving blade-guard 7.Edge of moving blade-guard 8.Adjusting wheel 9.Operating handle 10.Spindle-lock button 11.Blade-guard finger screw 12.Motor unit 13.Overload protection 14. Rating plate 15.Gripper unit 16.Gripper adjustment handle 17.
PAGE 8
Operation Fig C Exact PipeCut 200 pipecutting system operating instructions Before operating the tool Ensure that the motor unit is in the upright position. The yellow mark of the UNLOCK button is visible. Check that the blade is correctly fitted, in good condition and suitable for the material to be cut. Ensure the pipe saw guide wheels rotate.
PAGE 9
Operation Fig E Attaching the pipe saw to the pipe Open the pipe saw's gripper unit enough to suit the diameter of the pipe by rotating the adjustment handle located at the rear of the saw (Fig. E/1). Position the pipe saw on top of the pipe so that the edge of the lower blade guard is at the cutting mark. Fasten the pipe saw to the pipe by turning the gripper adjustment handle until the gripper grips firmly the pipe to be cut (Fig E/2). Lock the mechanism by turning the gripper safety (Fig E/3).
PAGE 10
Operation Select the sawing speed as per the material and the thickness of the wall. Too high speed can damage the blade, overload the pipe saw and give a poor sawing result. Fig J When the pipe is cut off, push the UNLOCK button forward until the yellow mark is visible and the locking is released (Fig L/1). Now raise the motor unit to starting position (Fig L/2). Release the power switch (Fig L/3).
PAGE 11
Operation, maintenance The wheel can be adjusted in 9 positions; mid position and 4 steps to left and right. To adjust the wheel, loosen the locking screw (Fig N/1) and turn the wheel center clockwise or counterclockwise to the desired position (Fig N/2), and lock the wheel again (Fig N/3). If the blade has wandered too much to the right, adjust wheel center clockwise. It the misalignment is to the left, adjust counterclockwise. The number of steps depend on the actual misalignment.
PAGE 12
Environment, guarantee Blade Check the condition of the blade. Replace a bent, blunt, or otherwise damaged blade with a new one. Using a blunt blade can overload the pipe saw’s electric motor. When you notice that the blade is blunt, do not continue sawing with it, as the blade may become so badly damaged that it will not be worth sharpening. A blade in sufficiently good condition can be sharpened a few times by a professional sharpening company. Use only Exactblades. Environment Separate collection.