Product manual

5 of 6
You can continue importing cartridges in the same manner until you have
filled as many cells as you want.
10.
10.10.
10. Press (as needed) to return to the Home screen.
REMOVING CARTRIDGES FROM THE AUTOLOADER
To remove cartridges:
1.
1.1.
1. At the Home screen, press , , or to access the main menus.
2.
2.2.
2. Press or until the command menu appears:
3.
3.3.
3. Press to see the menu selections, then press or until the
following screen appears:
4.
4.4.
4. Press to display the cell selection screen:
5.
5.5.
5. Press or to scroll through the occupied cell locations until the one
you want appears.
6.
6.6.
6. Press to start the export operation (or to cancel). When the
specified cartridge cell is in position at the cartridge access port, the door
slides open and the following message appears:
7.
7.7.
7. Reach through the access port, grasp the edge of the cartridge and pull it
straight out of the autoloader. Press any button to close the door. After the
door closes, the autoloader checks the cell to verify that the cartridge has
been removed. The autoloader also scans the affected cell to update its
cartridge inventory. The cell selection screen appears again with the next
available cell number:
You can continue removing cartridges in the same manner until you have
removed as many cartridges as necessary.
8.
8.8.
8. Press (as needed) to return to the Home screen.
Additional Information
For Magnum 1x7 Autoloader documentation, go to:
 www.exabyte.com/manuals
For tape drive documentation, go to:
 Hewlett-Packard—www1.hp.com/storage/tapestorage/ultriumdrives.html
 IBM—www.storage.ibm.com/tape/lto/oem/index.html
For Magnum 1x7 Autoloader technical support, go to:
 www.exabyte.com/contact
Quick Reference — Magnum 1x7 Autoloader
Operator Panel Buttons
The following table describes the actions performed by the operator panel
buttons. When the edges of a button are lit, the button is a valid choice for the
information currently displayed on the LCD. When the edges are dark, the
button is not a valid choice and performs no action.
Important
If you plan to store a cleaning cartridge in the
autoloader, you must store it in cell 7.
S e l e c t a C o m m a n d
E x p o r t
C a r t r i d g e s
E x p o r t C a r t r i d g e
F r o m C e l l # n
R e m o v e C a r t r i d g e
P r e s s A n y K e y
E x p o r t C a r t r i d g e
F r o m C e l l # n
Button Description
Next Choice (right arrow). Press this button to move forward
through the selections in a menu.
Note: If you are entering a password, press this button to move
forward through the available values at a character position. Press
and hold the button to move rapidly through the available
values.
Previous Choice (left arrow). Press this button to move backward
through the selections in a menu.
Note: If you are entering a password, press this button to move
backward through the available values at a character position.
Press and hold the button to move rapidly through the available
values.
Down a Level (down arrow). Press this button to move down into
a lower level of menus. For example, if the screen is displaying
one of the main menus, press this button to view that menu’s
sub-menus.
Note: If you are entering a password, press this button to move
forward through the character positions of the password.
Up a Level (up arrow) Press this button to return to the previous
level of menus. At the top level of menus, pressing this button
returns to the Home screen.
If you are making selections within a menu and change your mind
about a selection, press this button to return to the previous
screen without enacting the change.
Note: If you are entering a password, press this button to move
backward through the character positions of the password.
Select. Press this button to cause an operation displayed on the
LCD to be enacted. For example, if you are changing a SCSI ID,
pressing this button causes the new value you have entered to
take effect.
As confirmation, after you press this button, the original screen for
changing the value reappears and displays the new value.
REGISTER YOUR AUTOLOADER!
Be sure to register your Magnum 1x7 Autoloader for support
and product updates. You can register online at
www.exabyte.com/register.
Up a Level
Down a Level
Next
Previous
Select
Choice
Choice