User Manual

ManualsBrandsEvolve ManualsDomestic AppliancesT-100R

DCN: 100-22711-02 02/11 Evolve, Inc. 85 Denton Avenue, New Hyde Park, NY 11040 www.eguestcontrols.com

Page 1

Installation Guide

Model T-100R

Z-Wave Thermostat

This thermostat is compatible with most HVAC systems, including the following:

 24VAC systems Note: requires both the 24R and 24C (common) wires

 Standard gas/oil/electric heating systems

o 1 stage heating and cooling

o 2 stage heating and cooling

 Heat Pump systems:

o 1 stage heating and cooling

o 2 stage heating and cooling

o 2

or 3

stage Auxiliary heating (heat strips)

 Do NOT use for line voltage controls (120/240VAC)

Stop! Before removing your existing thermostat, be sure to label the

wires with the terminal markings on the old thermostat and record them

below.

Standard HVAC System Wiring

Terminal

Marking

Meaning

Typical Wire Color

Record the old thermostat wire

connections and terminal

marking here

24VAC Common

Blue

24VAC Return

Red

Fan

Green

W or W1

Heat stage 1

White

Y or Y1

Cool stage 1

Yellow

Heat stage 2

Orange

Cool stage 2

Black

Heat Pump HVAC System Wiring

Terminal

Marking

Meaning

Typical Wire Color

Record the old thermostat wire

connections and terminal

marking here

24VAC Common

Blue

24VAC Return

Red

Fan

Green

W or W1

Aux Heat

White

Y or Y1

Compressor stage 1

Yellow

O (or B*)

Change Over Valve

Orange (brown*)

Compressor stage 2

Black

* if you have a terminal marked “B” with a brown wire attached to it, that means you have a

changeover (C/O) with heating type heat pump system. Be sure to set the change over

type in the Installer Settings menu to C/O Type: w/Heat. Otherwise leave it set to

w/Cool.

Summary of content (8 pages)

PAGE 1
Installation Guide Model T-100R Z-Wave Thermostat This thermostat is compatible with most HVAC systems, including the following:   24VAC systems Note: requires both the 24R and 24C (common) wires Standard gas/oil/electric heating systems o 1 stage heating and cooling o 2 stage heating and cooling Heat Pump systems: o 1 stage heating and cooling o 2 stage heating and cooling o 2nd or 3rd stage Auxiliary heating (heat strips) Do NOT use for line voltage controls (120/240VAC)   Stop! Before removing
PAGE 2
INSTALLATION HVAC System Setup The thermostat requires that you setup the type and configuration of your HVAC system for proper operation. This is done in the Thermostat Info screen Setup button or the Installer Settings screen on the thermostat. The Installer Settings is a hidden screen. To access it, press the main menu button and when the main menu screen appears, press and hold the middle two buttons for 5 seconds.
PAGE 3
For Heat Pump systems: Change over valve (or reversing valve) type: Does your system change over with cooling operation or with heating operation? Check your existing thermostat connects to help determine this. If the original system had an orange wire connected to an “O” terminal, then you have a “changeover with cool” system. If you have a brown wire connected to the “B” terminal, then you have a “change over with heat” system.
PAGE 4
Delta Settings : The Delta T Setting is the delta, or difference between, the setpoint and current temp for determining when a heat or cool call comes on. The “delta” is the number of degrees away from setpoint. H/C Delta Range: 3 - 15 degrees. Default: 3F (1C) Sets the minimum separation between heating and cooling setpoints. Attempts to lower the cooling below the heating setpoint by this amount will PUSH the heating setpoint down to maintain this separation.
PAGE 5
Minimum Off Time (MOT) Range: 5-9 Minutes Default: 5 Sets the minimum off time before another heating/cooling cycle can begin. Provides compressor short cycle protection. Temp Response Range: 1-6 Default: 2 Adjust the temperature sensor sensitivity. Sets how fast the sensor responds to change. Fan Cycler The fan cycler function cycles the HVAC system fan for an ON period followed by an Off period continuously. Used to provide minimum air ventilation requirements.
PAGE 6
Installer Settings Summary Setting Range Default Display Lock Y or N N Locks out front buttons Y or N N Reduces delays for testing Std or HP Gas or Elec w/Heat or w/Cool Y or N Y or N Y or N 3 – 15 deg 1–8 0–8 1–8 Std Gas w/Cool N Y N 3 1 0 2 0–8 1–8 0–8 1–8 0–8 1–8 0–8 40-109F (4-42C) 44-113F (6-45C) 1-9 min 1-9 min 1-6 0 3 0 1 0 2 0 90F 60F 3 5 2 Service Mode Submenu Test Mode System Settings Submenu Mechanical Settings Submenu Sys Type Fan Type C/O Type 2nd Stage Heat Aux Heat 2nd Stage Coo
PAGE 7
Standard Gas/Electric HVAC System Wiring Thermostat back Optional 24R Connection for single transformer HVAC Systems RC and RH are jumpered together on thermostat board.
PAGE 8
Heat Pump HVAC System Wiring Thermostat back For Heat Pump systems, connect the 24R connection to either the 24RC or 24RH Cooling 24V Fan Cooling stage 1 Cooling stage 2 Remote Sensor 2 Remote Sensor 2 Sensor shield 24C 24RH W1 W2/O RS1 RS1 RSC H1 24RC G Y1 Y2 RS2 RS2 RSC Humidity Relay Com HC Shielded cable 24VAC Com 24V Heating Aux Heating Change Over Valve Remote Sensor 1 Remote Sensor 1 Sensor shield Humidity Relay Shielded cable Remote Indoor Sensor Remote Outside Sensor Heat Pump HVAC Syste