Original Instructions Originalbetriebsanleitung Notice Originale Instrucciones Originales Oryginalna Instrukcja Instruções Originais Instrucțiuni Iniţiale Оригинальные Инструкции Orijinal Talimatlar 026-0001, 026-0002, 026-0003 027-0001C, 027-0002C, 027-0003C, 027-0004, 027-0006, 027-0010 027-0001, 027-0002, 027-0003 027-0001A, 027-0002A, 027-0003A, 027-0004A, 027-0006A GB2438285 Original written in UK English Date Published: 01 / 06 / 2018
www.evolutionpowertools.
www.evolutionpowertools.com EN (1.2) INTRODUCTION IMPORTANT Please read these operating and safety instructions carefully and completely. For your own safety, if you are uncertain about any aspect of using this equipment please access the relevant Technical Helpline, the number of which can be found on the Evolution Power Tools website. We operate several Helplines throughout our worldwide organization, but Technical help is also available from your supplier. (1.3) CONTACT: Web: www.evolutionpowertools.
www.evolutionpowertools.com SPECIFICATIONS USA R185CCS R185CCSX R185CCSX+ 027-0004 027-0004C 027-0004A 15A 15A 15A 3700 min-1 / rpm 3700 min-1 / rpm 3700 min-1 / rpm 10.8 lb 11.2 lb 11.2 lb Max.
www.evolutionpowertools.com EN UK / EU / AUS R165CCSL R185CCS R185CCSX R185CCSX+ 026-0001 / 026-0002 / 026-0003 027-0001C / 027-0002C / 027-0003C 027-0001 / 027-0002 / 027-0003 027-0001A / 027-0002A / 027-0003A 1200W 1600W 1600W 1600W 1200W 1600W 1600W 1600W 3700 min-1 / rpm 3900 min-1 / rpm 3900 min-1 / rpm 3900 min-1 / rpm 3700 min-1 / rpm 3700 min-1 / rpm 3700 min-1 / rpm 3700 min-1 / rpm 4.3 kg 4.9 kg 5.1 kg 5.
www.evolutionpowertools.com VIBRATION Work Surface • Consider the work surface material; its condition, density, strength, rigidity and orientation. (1.5) Note: The vibration measurement was made under standard conditions in accordance with: EN 62841-1: 2015, EN 62841-2-5: 2014 WARNING: The vibration emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used.
www.evolutionpowertools.com Read Instructions Double Insulated CE Certification ETL Certification Waste Electrical & Electronic Equipment Triman - Waste Collection & Recycling Warning (RCM) Regulatory Compliance Mark for electrical and electronic equipment. Australian/New Zealand Standard (1.9) INTENDED USE OF THIS POWER TOOL WARNING: This product is a Hand Operated Circular Saw and has been designed to be used with special Evolution blades.
www.evolutionpowertools.com the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. (2.2) 1) General Power Tool Safety Warnings [Work area safety] a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gasses or dust. Power tools create sparks which may ignite the dust or fumes.
www.evolutionpowertools.com (2.5) 4) General Power Tool Safety Warnings [Power tool use and care]. a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at a rate for which it was designed. b) Do not use the power tool if the switch does not turn it on or off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
www.evolutionpowertools.com b) Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece. c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece. d) Never hold the workpiece in your hands or across your leg while cutting. Secure the workpiece to a stable platform. It is important to support the work properly to minimise body exposure, blade binding, or loss of control.
www.evolutionpowertools.com accidentally dropped, the lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. b) Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris.
www.evolutionpowertools.com USA 18 16 1 17 15 14 2 3 19 13 4 20 12 11 5 10 6 9 7 8 1. CUT MATERIAL EJECTION PORT 13. PRECISION ENGINEERED SOLE PLATE 2. THUMB LEVER 14. BEVEL ADJUSTMENT THUMB LEVER 3. MULTI-MATERIAL TCT BLADE 15. PROTRACTOR SCALE 4. LOWER BLADE GUARD 16. ARBOR LOCK BUTTON 5. PARALLEL EDGE GUIDE 17. LED LIGHT 6. ERGONOMIC FRONT HANDLE 18. DUST PORT CONNECTOR 7. CARBON BRUSHES 19. 25/32” INNER BLADE FLANGE 8. 5/16” HEX KEY (BLADE CHANGE) 20.
www.evolutionpowertools.com EN USA 18 16 1 17 21 19 14 2 3 13 DE 4 20 12 11 5 10 6 15 22 7 9 FR 8 23 1. 2. 3. 4. 5. 6. 7. 8. 9. 24 CUT MATERIAL EJECTION PORT THUMB LEVER MULTI-MATERIAL TCT BLADE LOWER BLADE GUARD PARALLEL EDGE GUIDE ERGONOMIC FRONT HANDLE CARBON BRUSHES 5/16” HEX KEY (BLADE CHANGE) DEPTH ADJUSTMENT LEVER 25 10. 11. 12. 13. 14. 15. 16. 17.
www.evolutionpowertools.com USA 18 16 1 17 21 14 2 3 19 13 4 20 12 11 5 10 6 15 22 7 9 8 1. CUT MATERIAL EJECTION PORT 13. PRECISION ENGINEERED TRACK COMPATIBLE SOLE PLATE 2. THUMB LEVER 14. THUMB LEVER 3. MULTI-MATERIAL TCT BLADE 15. REAR PROTRACTOR SCALE 4. LOWER BLADE GUARD 16. ARBOR LOCK BUTTON 5. PARALLEL EDGE GUIDE 17. LED LIGHT 6. ERGONOMIC FRONT HANDLE 18. DUST PORT CONNECTOR 7. CARBON BRUSHES 19. 25/32” INNER BLADE FLANGE 8. 8MM HEX KEY (BLADE CHANGE) 20.
www.evolutionpowertools.com EN UK / EU / AUS 1 16 15 2 14 3 DE 13 4 12 5 11 10 6 9 7 FR 8 1. CUT MATERIAL EJECTION PORT 12. UPPER BLADE GUARD 2. THUMB LEVER 13. PRECISION ENGINEERED SOLE PLATE 3. MULTI-MATERIAL TCT BLADE 14. THUMB LEVER 4. LOWER BLADE GUARD 15. PROTRACTOR SCALE 5. PARALLEL EDGE GUIDE 16. ARBOR LOCK BUTTON 6. ERGONOMIC FRONT HANDLE 7. CARBON BRUSHES 8. 8MM HEX KEY (BLADE CHANGE) 9. DEPTH ADJUSTMENT LOCKING LEVER 10. DEPTH SCALE ES 11.
www.evolutionpowertools.com UK / EU 17 16 1 15 14 2 3 13 4 12 11 5 10 6 9 7 8 1. CUT MATERIAL EJECTION PORT 12. UPPER BLADE GUARD 2. THUMB LEVER 13. PRECISION ENGINEERED SOLE PLATE 3. MULTI-MATERIAL TCT BLADE 14. THUMB LEVER 4. LOWER BLADE GUARD 15. PROTRACTOR SCALE 5. PARALLEL EDGE GUIDE 16. ARBOR LOCK BUTTON 6. ERGONOMIC FRONT HANDLE 17. DUST PORT CONNECTOR 7. CARBON BRUSHES 8. 8MM HEX KEY (BLADE CHANGE) 9. DEPTH ADJUSTMENT LOCKING LEVER 10. DEPTH SCALE 11.
www.evolutionpowertools.com EN UK / EU 17 16 1 18 20 14 2 3 13 4 DE 21 12 5 11 6 22 10 7 15 9 8 1. CUT MATERIAL EJECTION PORT 12. UPPER BLADE GUARD 2. THUMB LEVER 13. PRECISION ENGINEERED TRACK COMPATIBLE SOLE PLATE 3. MULTI-MATERIAL TCT BLADE 4. LOWER BLADE GUARD 5. PARALLEL EDGE GUIDE 6. ERGONOMIC FRONT HANDLE 7. CARBON BRUSHES 8. 8MM HEX KEY (BLADE CHANGE) 9. DEPTH ADJUSTMENT LOCKING LEVER FR 19 14. THUMB LEVER 15. REAR PROTRACTOR SCALE 16. ARBOR LOCK BUTTON 17.
www.evolutionpowertools.com UK / EU 17 16 1 18 14 2 3 13 4 12 11 5 10 6 15 19 7 9 8 1. CUT MATERIAL EJECTION PORT 12. UPPER BLADE GUARD 2. THUMB LEVER 13. PRECISION ENGINEERED TRACK COMPATIBLE SOLE PLATE 3. MULTI-MATERIAL TCT BLADE 14. THUMB LEVER 4. LOWER BLADE GUARD 15. REAR PROTRACTOR SCALE 5. PARALLEL EDGE GUIDE 16. ARBOR LOCK BUTTON 6. ERGONOMIC FRONT HANDLE 17. DUST PORT CONNECTOR 7. CARBON BRUSHES 18. TRACK ADJUST TURN BUTTONS 8. 8MM HEX KEY (BLADE CHANGE) 19.
www.evolutionpowertools.com EN Fig. 1 Fig. 2 Fig. 3 DE Fig. 4 Fig. 5 Fig. 6 FR Fig. 7a Fig. 7b Fig. 7c ES Fig. 8 Fig. 9 Fig.
www.evolutionpowertools.com Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 21 Fig. 22 1 -2mm Fig.
www.evolutionpowertools.com EU Dust Port Connector EN US Dust Port Connector Fig. 23 Fig. 24 Fig. 25 DE Fig. 26 Fig. 27 Fig. 28 FR Fig. 29 Fig. 30 Fig. 31 ES Fig. 32 Fig. 33 Fig.
www.evolutionpowertools.com (10) PREPARATION WARNING: Always disconnect the machine from the power source before making any adjustments. Note: These machines are equipped with an approved power cord and plug for the intended country of use. Do not alter or modify the power cord. (10.1) INSTALLING / REMOVING A BLADE WARNING: Use only genuine Evolution blades (or those approved by Evolution Power Tools), which are designed for use in these machines.
www.evolutionpowertools.com (11) PARALLEL EDGE GUIDE A Parallel Edge Guide (Fig. 8) which can be particularly helpful when rip cutting, is supplied with all CCS machines. The guide can be fitted to the front of the sole plate. The guides arm should be inserted through the rectangular slots positioned at either side (front) of the pressed steel sole plate, and slid under the centrally located adjustment locking screw. (Fig. 9) Note: The Parallel Edge Guide can be fitted on either side of the sole plate.
www.evolutionpowertools.com the following general advice on safe operational procedures and practices for the consideration of the operator. This advice cannot be exhaustive as Evolution has no influence on the type of workshops or working environments in which these machines may be used. We recommend that the operator seeks advice from a competent authority or the workshop supervisor if they are at unsure of any aspect of using these machines.
www.evolutionpowertools.com CUTTING TRACKS Evolution CCSX series machines (refer to the Specification Page for applicable models) have been engineered and featured in such a way as to make them Cutting Track compatible. Note: Any circular saw that is capable of being used with a Cutting Track will have a channel along the under surface of the sole plate (Fig. 16) Evolution machines so equipped can be attached to, and used with most Cutting Tracks (Guides) currently available.
www.evolutionpowertools.com appropriate helpline. The replacement self adhesive Linear Seal supplied is a direct substitution to the fitted original. Simply pull the old seal gently from the track and replace with the new seal. Before the first use of the Evolution Cutting Track the cut line sealing strip (Fig. 21) needs to match the saw and blade. To match saw to track: • Fully assemble the Cutting Track. • Refer to the section entitled ‘Track Positioning and Clamping’.
www.evolutionpowertools.com position the Track on the workpiece and secure by tightening the clamps. • Ensure that the edge of the linear seal runs exactly along the marked out cutting line. WARNING: The Cutting Track must overhang the worpiece at the ‘lead in’ edge. (Fig. 24) The lower blade guard will need to be retracted manually and pivot upwards into the upper blade guard as the circular saw is placed on the track. WARNING: In this position the blade is exposed.
www.evolutionpowertools.com Front of Blade Guide (Fig. 29) Note: Evolution machines compatible with Note: If you are unsure of which features are provided on your machine, consult the Specification Page provided in this manual. The LED Light is positioned to the left hand (LH) side of the blade. (Fig. 27) The beam from the LED will light up the left hand side of the blade and also illuminate any marking out lines present on the workpiece.
www.evolutionpowertools.com The cable should not pose a trip (or any other type) of hazard to the operator or any bystanders. • Do not force the machine. • Allow the speed of the saw blade do the work. Cutting performance will not be improved by applying excessive pressure to the machine and blade life will be reduced. • When using the parallel edge guide, ensure that it is parallel with the blade.
www.evolutionpowertools.com R165CCSL & 185CCS Turn the adjustment screw (Fig. 31) clockwise or counter clockwise using a 4mm Hex Key (not supplied) until the blade is at exactly 90˚ to the sole plate. R185CCSX & 185CCSX+ Turn the adjustment screws (Fig. 32) clockwise or counter clockwise using a 3mm Hex Key (not supplied) until the blade is at exactly 90˚ to the sole plate. To check 45˚ position (R185CCSX & 185CCSX+ ): • Set the blade to the 45˚ position with the tilting mechanism against its stop.
www.evolutionpowertools.com EN EC DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below.
AUS EU Total Tools (Importing) Pty Ltd 20 Thackray Road Port Melbourne Vic 3207 Evolution Power Tools SAS 61 Avenue Lafontaine 33560, Carbon-Blanc Bordeaux T: 03 9261 1900 T: +33 (0)5 57 30 61 89 UK USA T: +44 (0)114 251 1022 T: 866-EVO-TOOL Evolution Power Tools Ltd Venture One, Longacre Close Holbrook Industrial Estate Sheffield, S20 3FR Evolution Power Tools LLC 8363 Research Drive Davenport, IA 52806 EPT QR CODE 027-9201.
