特种计算机 Industrial Computer 产品说明书 User Manual ERC-1005 轨道交通 AFC 系统终端 AFC Terminal for Metro Version: C01
Legal Information Warnings Please pay attention to the tips within the manual so as to avoid personal injury or property losses. The tips for personal injury are indicated in warning triangles while the tips only related to property losses have no warning triangles. The warning tips are listed as follows with the hazardous scale from severe to slight. Danger If handled carelessly, death or severe human injury will occur. Warning If handled carelessly, death or severe human injury might occur.
Copyright Notice Information offered in this manual is believed to be correct at the time of printing, and is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of improper installation and/or use, or inability to use the product or documentation.
About this manual Scope of the Manual The manual is appropriate for EVOC ERC-1005. Convention The term “the Board” or “the Product” within the manual stands for EVOC ERC-1005. Instructions Safety instructions To avoid property losses or individual injury, please pay attention to the safety instructions within the manual. The warnings within the manual are marked with warning triangle , which is dependent upon the scale of the potential hazard.
Contents 1. Product Introduction .................................................................................................1 1.1 Overview.........................................................................................................1 1.2 Product Specifications ....................................................................................1 2. Application Scheme ..................................................................................................4 2.1 Transportation .......
4.4.6 Display Connector .............................................................................14 4.4.7 GPIO ..................................................................................................15 4.4.8 Mouse & Keyboard Connector (adopts standard 2-in-1 mouse & keyboard connector)..........................................................................16 4.4.9 Serial Port ..........................................................................................16 4.5 Operation Control ..
Product Introduction 1. Product Introduction 1.1 Overview ERC-1005 is a low-power fanless embedded PC, which contains Intel® Atom™ low power consumption CPU and supports WinXP, Linux, WinCE and Vxworks operating system.
Product Introduction Audio Function Expansion Bus Adopts HD standard, supporting MIC-IN/LINE-OUT Expandable to one standard PC/104 card External IO Connectors Dimensions (excluding the hangers) Main Performance Index Weight Ten serial ports: COM3 ~ COM5 are isolation serial ports; COM2, COM9 and COM10 support to switch among RS-232/RS-422/RS-485; while COM9 supports Modem wake-up function; Two 10/100/1000Mbps LAN ports; Two VGA display connectors; One LVDS connector (only supports
Product Introduction EMC Reliability Safety Mechanical and Environment Adaptability Power Feature GB 9254-2008 Radiation disturbance, class A; GB 9254-2008 Conducted susceptibility, class A; GB/T 17626.2.2006 Electrostatic discharge, level 2; GB/T 17626.4-2006 Burst Immunity, level 2; GB/T 17626.5-2008 Surge (Impact) immunity, level 2; GB/T 17626.6-2008 Conducted susceptibility, level 2; GB/T 17626.8-2006 Power frequency magnetic field, level 2; GB/T 17626.
Application Scheme 2. Application Scheme 2.1 Transportation Well-packaged products are suited for transportation by all kinds of vehicles. During transportation, products should not be put in open cabin or carriage. During transshipping, products should not be stored in open air without protection from the atmospheric conditions.
Application Scheme 2.3 Opening the Box and Initial Examination Opening the Box Please pay attention to the following issues when opening the box: ● Do not discard the original packing material. Please keep the original packing material for re-transportation. ● Please keep the documentation at a safe place. The documentation is required for initial device debugging, which is a component of the device.
Device Connection 3. Device Connection 3.1 Notices before Connection Warning Peripherals with reverse polarity must not be connected or built-in. Warning The device only operates when connected with grounded power. No operation is allowed when the device power is ungrounded or only impedance is grounded. Warning Rated voltage of the device in use shall be in accord with power feature of the product. Note: Only the peripheral devices approved for industrial application can be used.
Device Connection 3.3 Connecting the Device to Power Steps to connect the device to power: Please make sure the positive end and the negative end of the power cord are connected correctly when connecting the power cord ①. Please refer to the pin definitions of the power connector for detailed information. Connect the power cord with the connector ② and press down the switch ① with the silkscreen of “-”. The green power LED indicator on the rear panel of the PC is lit and the PC is powered on.
Instructions 4. Instructions 4.1 Product Outline 4.1.1 PC with Movable Scaffolding 4.1.
Instructions 4.2 Product Appearance and Installation Dimensions 4.2.
Instructions 4.2.
Instructions 4.
Instructions Rear View of the Device Item Description ⑤ GND screw ⑥ USB5/USB6 ⑦ Power switch ⑧ Power input terminal 4.4 Pin Definitions 4.4.1 Power Connector Pin Signal Name 1 + 2 - 3 NC 4 NC 4.4.2 Audio Connector Pin Signal Name 1 LINE_OUT 2 MIC_IN AUDIO 4.4.
Instructions 4.4.4 LAN Port (LAN1 and LAN2 are standard connectors) LILED (Dual-Color: O/G) LAN Speed Indicator Green 1000Mbps Data being transmitted Orange 100Mbps No data being transmitted Off 10Mbps ACTLED (Green) LAN Activity Status Indicator Blink Off 4.4.
Instructions 4.4.6 Display Connector 1. Two VGAs, adopting standard DB15 connectors VGA1/VGA2 Pin Signal Name Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 NC 10 GND 11 NC 12 DDCDATA 13 HSYNC 14 VSYNC 15 DDCCLK 2. One single-channel 18bit LVDS connector, adopting standard DB24+4 connector; Note: this connector supports LVDS signals; please do not connect the DVI cable with the DVI connector on the display directly.
Instructions 4.4.7 GPIO GPIO1 is the digital GPIO while GPIO2 is the isolation GPIO; the pin definitions are as follows: GPIO1 GPIO2 Pin Signal Name Pin Signal Name 1 DI16 2 DI17 3 DI18 4 DI19 5 DI20 6 DI21 7 DI22 8 DI23 9 DI24 10 DI25 11 DI26 12 DI27 13 DI28 14 DI29 15 DI30 16 DI31 17 GND 18 GND 19 +5V 20 +12V Pin Signal Name Pin Signal Name 1 IDO0 2 IDO1 3 IDO2 4 IDO3 5 IDO4 6 IDO5 7 IDO6 8 IDO7 9 EO.GND 10 EO.
Instructions 4.4.8 Mouse & Keyboard Connector (adopts standard 2-in-1 mouse & keyboard connector) KM1 Pin Signal Name 1 KB_DATA 2 MS_DATA 3 GND 4 +5V 5 KB_CLK 6 MS_CLK 4.4.9 Serial Port COM1 and COM2 support RS-232/RS-422/RS-485 mode selection; COM1 supports Modem wake-up function. COM3 ~ COM5 are isolation serial ports: COM3 and COM5 only support RS-232 mode, COM4 can switch among RS-232/RS-422/RS485 mode. COM6 ~ COM10 support RS-232 mode.
Instructions RS-232/RS-422/RS-485 mode selection for COM1 (motherboard) Mode Selection Pin RS-232 Setting (Default) JP3/JP4/JP5 RS-422 RS-485 JP3 1-2 5-6 3-4 JP4 1-3, 2-4 3-5, 4-6 3-5, 4-6 JP5 1-3, 2-4 3-5, 4-6 3-5, 4-6 RS-232/RS-422/RS-485 mode selection for COM2 (motherboard) Mode Selection Pin RS-232 Setting (Default) JP8/JP9/JP10 RS-422 RS-485 JP8 1-2 5-6 3-4 JP9 1-3, 2-4 3-5, 4-6 3-5, 4-6 JP10 1-3, 2-4 3-5, 4-6 3-5, 4-6 Signal Name Pin COM3/COM4/COM5 RS-232 RS-422
Instructions RS-232/RS-422/RS-485 mode selection for COM port RS-232/RS-422/RS-485 mode selection for COM4 (IO board) Mode Selection Pin Setting RS-232 (Default) SW1 SW2 SW3 SW1 ~ SW5 SW4 SW5 - 18 - RS-422 RS-485 1 / ON OFF 2 / OFF ON 3 / ON ON 4 / NC NC 1 / OFF ON 2 / OFF ON 3 / NC NC 4 / NC NC 1 ON OFF OFF 2 OFF ON ON 3 NC NC NC 4 NC NC NC 1 / ON ON 2 / ON OFF 3 / ON ON 4 / ON OFF 1 ON OFF OFF 2 OFF ON ON 3 ON OFF OFF 4
Instructions 4.5 Operation Control Warning Pressing On/Off button won’t cut off the power of the PC! Caution Data loss might occur when implementing hardware reset on PC. Control Button Item ① ② ③ Description Power on/off button of the PC Clearing CMOS button Use a sharp-point object or clip to operate the Clearing CMOS button when the PC is powered off and disconnected from power supply. Pressing button signal will reset BIOS and restore the BIOS setting to factory default value.
Assembly and Maintenance 5. Assembly and Maintenance 5.
Assembly and Maintenance 5.2 Installing the Cover 1、 Remove the expansion board module; 2、 Loosen the six screws fixing the cover by screwdriver, two each on both sides and on the rear; 3、 Loosen the screws fixing the cover and the cover supporting bar by screwdriver; 4、 Uplift the cover vertically. 5.3 Removal and Installation of Motherboard 5.3.
Assembly and Maintenance 5.3.2 Removing the Motherboard 1、 Loosen the two captive screws on both sides of the motherboard panel; 2、 Horizontally open the assisting handles outward to remove the motherboard; 3、 Remove the expansion card in the same way. 5.
Assembly and Maintenance 5.
Installing the Drivers 6. Installing the Drivers Regarding the driver program of this product, please refer to the enclosed CD.
Appendix 7. Appendix 7.1 Troubleshooting and Solutions Common Malfunctions The device is not operating Reasons No power supply Please check the power supply and the power cable/connector. Improper device operating environment 1. Check with the environment conditions; 2. Please wait for twelve hours before powering on the device shipped in cold weather. The display has not been turned on Turn on the display The display is under “power saving” mode Press any key on the keyboard.
Appendix BIOS setting is correct while the time and date are incorrect. USB device has no response The computer is not booted or displays “Boot device not found” Insufficient backup battery capacity Replace the battery USB port is disabled in BIOS Use other USB ports or enable that port. USB 2.0 device is connected; however, USB 2.0 is disabled. Enable USB 2.0. USB port is supported by operating system. 1. Enable USB Legacy Support for the mouse and keyboard (Legacy USB is supported); 2.
