User manual

ManualsBrandsEVOC ManualsComputer equipmentEC3-1816CLD2NA

特种计算机

Industrial Computer

产品说明书

User Manual

EC3-1816CLD2NA

Cedar Trail + NM10 3.5 寸主板

Cedar Trail+NM10 3.5-inch

Motherboard

版本：B00

Summary of content (49 pages)

PAGE 1
特种计算机 Industrial Computer 产品说明书 User Manual EC3-1816CLD2NA Cedar Trail + NM10 3.5 寸主板 Cedar Trail+NM10 Motherboard 版本：B00 3.
PAGE 2
Legal Information Warnings Please pay attention to the tips within the manual so as to avoid personal injury or property losses. The tips for personal injury are indicated in warning triangles while the tips only related to property losses have no warning triangles. The warning tips are listed as follows with the hazardous scale from severe to slight. Danger If handled carelessly, death or severe human injury will occur. Warning If handled carelessly, death or severe human injury might occur.
PAGE 3
Copyright Notice Information offered in this manual is believed to be correct at the time of printing, and is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of improper installation and/or use, or inability to use the product or documentation.
PAGE 4
About this manual Scope of the Manual The manual is appropriate for EVOC EC3-1816CLD2NA. Convention The term “the PC” or “the Product” within the manual usually stands for EVOC EC3-1816CLD2NA. Instructions Safety instructions To avoid property losses or individual injury, please pay attention to the safety instructions within the manual. The warnings within the manual are marked with warning triangle potential hazard.
PAGE 5
Contents 1. Product Introduction .................................................................................................1 1.1 Overview............................................................................................................1 1.2 Mechanical Dimensions, Weight and Environment............................................1 1.3 Typical Consumption .........................................................................................2 1.4 Microprocessor..............................
PAGE 6
2.8 USB Port .......................................................................................................... 11 2.9 LAN Port..........................................................................................................12 2.10 Audio Port ......................................................................................................13 2.11 Mouse/Keyboard Port.....................................................................................13 2.12 SATA Interface ...............
PAGE 7
Product Introduction 1. Product Introduction 1.1 Overview This motherboard contains Intel® Atom™D2550/N2600 + NM10 chipset (EC3-1816CLD2NA-D2550 contains Intel® Atom™ D2550 + NM10 chipset, EC3-1816CLD2NA-N2600 contains Intel® Atom™ N2600 + NM10 chipset), D2550 is 1M Cache 1.86GHz，N2600 is 1M Cache 1.6GHz；supports onboard 2GB DDR3 memory (EC3-1816CLD2NA-D2550 motherboard supports onboard 1066MHz 2GB memory; EC3-1816CLD2NA-N2600 motherboard supports onboard 800MHz 2GB memory).
PAGE 8
Product Introduction  Storage environment: Temperature: -40℃～80℃ Humidity: 5%～95% (non-condensing) 1.3 Typical Consumption The typical consumption is calculated based on the following configuration under idle status. EC3-1816CLD2NA-N2600 CPU：Onboard Intel® Atom ™ CPU N2600 @ 1.60GHz Memory: Onboard Samsung/DDRIII 1066/2G  +12V@0.68A；+5%/-3%； EC3-1816CLD2NA-D2550 CPU：Onboard Intel® Atom ™ CPU D2550 @ 1.86GHz Memory: Onboard Samsung/DDRIII 1066/2G  +12V@0.9A；+5%/-3%； 1.
PAGE 9
Product Introduction  The maximum resolution and refresh rate supported by VGA is 1920×1200@60Hz, and that supported by LVDS is 1920×1080@60HZ. 1.8 Network Provides two 10/100/1000Mbps network ports; LAN1 supports Wake-On-LAN. 1.9 Audio HDA standard, supporting MIC-IN/LINE-IN/LINE-OUT. 1.10 Power Feature Single 12V power supply. 1.11 Watchdog  255 levels, programmable by minute or second;  Supports watchdog timeout interrupt or reset system. 1.
PAGE 10
Installation Instructions 2. Installation Instructions 2.1 Product Dimensions Drawing 146.1 130 102 65 .5 ?8 4.3 6.5 14.1 12.5 3.2 3.2 12.4 25 25 8.7 4.1 1.6 15.5 12.6 6.3 5.1 39 22 146.1 137.2 95.3 101.6 Unit: mm Warning! Please adopt appropriate screws and proper installation methods (including board allocation, CPU and heat sink installation, etc); otherwise, the board may be damaged. It is recommended to use M3x6 GB9074.4-88 screws at H1 ~ H4.
PAGE 11
Installation Instructions 2.
PAGE 12
Installation Instructions 2.3 Structure Diagram VGA DB15 D2550/ N2600 CPU CH A DP to LVDS Onbord DDR3 DDI1 DMI SATA II (1*7) SATA to CF SATA1 SATA2 NM10 Intel LAN1 RJ45 Connector PCI-E Port 2 Intel LAN2 RJ45 Connector PCI-E Port 4 USB Mini PCIE HDA Audio SPI SPI Flash LPC USB 2.0 X6 PCI-E Port1 SIO GPIO COM*4 PS/2 (K/M) WDT FAN Tip: How to identify the first pin of the jumpers and connectors 1.
PAGE 13
Installation Instructions 2.4 Jumper Setting 1. JCC1: Clear/Keep CMOS Setting (Pitch: 2.0mm) CMOS is powered by the button battery on board. Clearing CMOS will restore original settings (factory default). The steps are listed as follows: (1) Turn off the computer and unplug the power cable; (2) Instantly short circuit JCC1; (3) Turn on the computer; (4) Follow the prompt on screen to enter BIOS setup when booting the computer, load optimized defaults; (5) Save and exit. Please set as follows: JCC1 2.
PAGE 14
Installation Instructions 4. JCF1: CF Card Operating Voltage Selection (Pitch: 2.0mm) JCF1 5. Setup Function 1-2 Short +3.3V 2-3 Short +5V（Default） JLCD1: Select LCD Operating Voltage (Pitch: 2.0mm) Different LCD screens have different voltages; the board provides two voltage options, +3.3V and +5V. Only when the selected LCD voltage is in accord with the LCD screen operating voltage in use, can the LCD screen operate normally. Please set as follows: Setup JLCD1 Function 1-2 Short +3.
PAGE 15
Installation Instructions 2. This motherboard provides three 2×5Pin COM ports (pitch: 2.0mm). Their pin definitions are as follows: COM2～COM4 Pin Signal Pin Signal 1 DCD# 2 RXD 3 TXD 4 DTR# 5 GND 6 DSR# 7 RTS# 8 CTS# 9 RI# 10 NA 2.6 LCD Backlight Control Connector This board provides one 1×4Pin wafer LCD backlight control connector (pitch: 2.0mm).
PAGE 16
Installation Instructions 2.7 Display Port 1. This motherboard provides one standard DB15 VGA port. Its pin definitions are as follows: VGA1 2. Pin Signal Pin Signal 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 NC 10 GND 11 NC 12 DDCDATA 13 HSYNC 14 VSYNC 15 DDCCLK LVDS port This board provides one dual-channel 24bitLVDS port (LVDS1, LVDS2; pitch: 1.0mm). If single-channel 18-bit/24-bit LVDS screen is used, LVDS data cable must be connected to LVDS1.
PAGE 17
Installation Instructions LVDS2 Pin Signal Pin Signal 1 LVDSE_D0+ 2 LVDSE_D0- 3 GND 4 GND 5 LVDSE_D1+ 6 LVDSE_D1- 7 GND 8 GND 9 LVDSE_D2+ 10 LVDSE_D2- 11 GND 12 GND 13 LVDSE_CLK 14 LVDSE_CLK 15 GND 16 GND 17 LVDSE_D3+ 18 LVDSE_D3- 19 VDD 20 VDD Note: LVDSOx refers to the odd lines of dual-scan PANEL, and LVDSEx refers to the even lines of dual-scan PANEL.
PAGE 18
Installation Instructions 2.9 LAN Port The motherboard provides two 10/100/1000Mbps LAN ports: one is a RJ45 connector LAN1, the other is a 2×7 pin header (LAN2, pitch: 2.0mm).
PAGE 19
Installation Instructions 2.10 Audio Port This board provides one 2×5Pin audio port (pitch: 2.0mm). AUDIO1 Pin Signal Pin Signal 1 LOUT_R 2 LOUT_L 3 GND_AUDIO 4 GND_AUDIO 5 LIN_R 6 LIN_L 7 GND_AUDIO 8 GND_AUDIO 9 MIC_L 10 MIC_R 2.11 Mouse/Keyboard Port This board provides one Mini DIN 1-to-2 PS/2 port. Pin Signal 1 KB_DATA 2 MS_DATA 3 GND KM1 4 +5V 5 KB_CLK 6 MS_CLK 2.12 SATA Interface This motherboard provides one double-layer SATA interface.
PAGE 20
Installation Instructions 2.13 SATA HDD Hot Plugging Notes for hot-swap of SATA hard disk: 1. The hard disk shall support SATA 2.0 and use 15-pin SATA hard disk power connector. 2. The driver of chipset shall support the hot-swap of SATA hard disk. 3. Hot-swap of SATA hard disk where the operating system is located is forbidden when system is powered-on. SATA Data Cable SATA Power Cable Please carry out hot plugging as follows. Improper operation may destroy the hard disk or result in data loss.
PAGE 21
Installation Instructions Step 3: Please connect the 15-pin SATA power connector (black) to the SATA hard disk. Step 4: Please connect the SATA data cable to the SATA hard disk. SATA HDD Hot Unplugging Steps Step 1: Uninstall the hard disk from the device manager. Step 2: Unplug the data cable from the SATA hard disk. Step 3: Unplug the SATA 15-pin power connector (black) from the SATA hard disk.
PAGE 22
Installation Instructions 2.14 GPIO Port GPIO1 (Pitch: 2.0mm) Pin Signal Pin Signal 1 GPIO1 2 GPIO5 3 GPIO2 4 GPIO6 5 GPIO3 6 GPIO7 7 GPIO4 8 GPIO8 9 GND 10 NC Note: By the factory default, the pin 1, 3, 5 and 7 of the connector are TTL input while pin 2, 4, 6, and 8 are CMOS output. The factory default state is high level and the voltage range for input/output signal is 0-5V. 2.15 Fan Connector The motherboard provides one 1×4Pin CPU fan connector (CPUFAN1, pitch: 2.54mm).
PAGE 23
Installation Instructions 2.16 Power Connector 1. AT power connector, single 12V power connector (pitch: 4.2mm) PWR1 2. Pin Signal 1 GND 2 GND 3 +12V 4 +12V SATA power connector Wafer 1x4P power connector (white, pitch: 2.54mm) PWR2 Pin Signal 1 +12V 2 GND 3 GND 4 +5V 2.17 Status Indicating and Control Connectors 1. Power switch and HDD indicator ports (Pitch: 2.54mm) FP1 2.
PAGE 24
Installation Instructions 3. Speaker output port (Pitch: 2.54mm) FP3 Pin Signal 1 SPEAKER 2 NC 3 GND 4 +5V 2.18 Mini-PCIe Port This board provides one Mini-PCIe slot, which supports WiFi wireless network card. MPCIE1 (on the back side of the board) - 18 - Pin Signal Pin Signal 1 WAKE# 2 +3.3VSB 3 NC 4 GND 5 NC 6 +1.
PAGE 25
Installation Instructions 37 GND 38 NC 39 41 +3.3V 40 GND +3.3V 42 NC 43 GND 44 NC 45 Reserved 46 NC 47 Reserved 48 +1.5V 49 Reserved 50 GND 51 Reserved 52 +3.3VSB 2.19 CF Card (optional) This motherboard provides CF card (optional), which can be set in the BIOS SETUP. Please refer to BIOS Setup part for detailed information. CF card is a sort of high speed memory, small in size and easy to use. The storage capacity varies with different cards in use, such as 128M, 256M.
PAGE 26
Installation Instructions - 20 - 13 VCC 38 VCC 14 GND 39 CSEL# 15 GND 40 VS2# 16 GND 41 RESET# 17 GND 42 IORDY 18 A2 43 DREQ 19 A1 44 DACK# 20 A0 45 DASP# 21 D0 46 ATA66_DET 22 D1 47 D8 23 D2 48 D9 24 WP/IOCS16# 49 D10 25 CD2# 50 GND EC3-1816CLD2NA
PAGE 27
BIOS Setup 3. BIOS Setup 3.1 UEFI Overview UEFI (Unified Extensible Firmware Interface) is the latest computer firmware to replace traditional BIOS. UEFI is solidified in the flash memory on the CPU board.
PAGE 28
BIOS Setup 3.3 Basic Function Setting for UEFI After starting SETUP program, the main interface of Aptio Setup Utility - Copyright (C) 2009 American Megatrends, Inc. will appear: Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 29
BIOS Setup  Advanced Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 30
BIOS Setup Used to select resolution of onboard LVDS screen.  LVDS BackLight Value Used to select backlight brightness.  CPU Configuration Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 31
BIOS Setup  IDE Configuration Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Advanced SATA Port0 SATA Port1 SATA Controller(S) Configure SATA as Not Present Not Present [Enabled] [IDE] →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201. Copyright (C) 2009,American Megatrends, Inc. SATA Port0 ~ 5 dynamically detect whether there are SATA devices on motherboard.
PAGE 32
BIOS Setup  Legacy USB Support This option is used to support legacy USB devices (keyboard, mouse, storage device, etc). When it is set to Enabled, the USB devices can be used in the OS that does not support USB, such as DOS. When it is set to Disabled, the legacy devices cannot be used in the OS that does not support USB. Note: USB can be used in EFI application, such as in Shell.  Super IO Configuration Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 33
BIOS Setup * Serial Port0 ~ 3 This option is used to enabled or disable the current serial port. * Device Settings This option is used to display the current resource configuration of the serial port. * Change Settings This option is used to configure the resources (IO and IRQ) used by the serial port.  H/W Monitor Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Advanced PC Health Status System Temperature CPU Temperature CpuFan Speed Vcore V3.3 V5.0 V12.
PAGE 34
BIOS Setup  Vcore CPU core voltage.  V3.3/ V5.0/V12.0 Turn on/off the power to output voltage.  VBAT CMOS battery voltage.  PPM Configuration Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Advanced PPM Configuration EIST [Enabled] →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201. Copyright (C) 2008,American Megatrends, Inc.
PAGE 35
BIOS Setup  Clock Generator Configuration Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Advanced Clock Generator Configuration Spread Spectrum →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit [Disabled] Version 2.00.1201. Copyright (C) 2009,American Megatrends, Inc.  Spread Spectrum This option is used to control the spread spectrum function of the clock signal.
PAGE 36
BIOS Setup  Host Bridge Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Chipset  Intel IGD Configuration ******* Memory Information ********** Memory Frequency MHz(DDR3) Total Memory DIMM#0 DIMM#1 800 1024 MB Not Present 1024 MB →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201. Copyright (C) 2008,American Megatrends, Inc.
PAGE 37
BIOS Setup  South Bridge Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Chipset  TPT Devices  PCI Express Root Port 0  PCI Express Root Port 1  PCI Express Root Port 2  PCI Express Root Port 3 Restore AC Power Loss [Last State] →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201. Copyright (C) 2009,American Megatrends, Inc.
PAGE 38
BIOS Setup  TPT Devices Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Chipset Azalia Controller Select USB Mode UHCI #1 (ports 0 and 1) UHCI #2 (ports 2 and 3) UHCI #3 (ports 4 and 5) UHCI #4 (ports 6 and 7) USB 2.0(EHCI) Support [HD Audio] [By Controllers] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201.
PAGE 39
BIOS Setup  PCI Express Root Port X Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Chipset PCI Express Port X [Enabled] →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201. Copyright (C) 2008,American Megatrends, Inc.  PCI Express Port X This option is used to enable or disable the PCIE0-3 ports.  Boot Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 40
BIOS Setup This option is used to configure the system booting priorities. #1 represents the highest priorities while #n represents the lowest priorities.  Hard Drive BBS Priorities This option is used to configure the priorities of the legacy devices in BBS. #1 represents the highest priorities while #n represents the lowest priorities.  Security Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 41
BIOS Setup  Save & Exit Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Main Advanced Chipset Boot Security Save Changes and Reset Discard Changes and Reset Save & Exit →←：Select Screen ↑↓：Select Item Enter：Select +/-：Change Opt F1：General Help F2：Previous Values F3：Optimized Defaults F4：Save ESC：Exit Version 2.00.1201. Copyright (C) 2009,American Megatrends, Inc.  Save Changes and Reset The option is used to save changes and reset.
PAGE 42
BIOS Setup  APIC Advanced programmable interrupt controller. Most motherboards above P4 level support APIC and provide more than 16 interrupt sources, like IRQ16 - IRQ23; while some others can have up to 28 interrupt sources, such as motherboard supporting PCI-X. However, relevant OS are required to enable that function.  IO Port Address Only 16 IO address lines are designed for X86, from 0 ~ 0FFFFh; there is 64K for the system I/O address space.
PAGE 43
BIOS Setup  IRQ Assignment Table There are 15 interrupt sources of the system. Some are occupied by the system devices. Only the ones that are not occupied can be assigned to other devices. ISA device requests exclusive use of its interrupt. Only the plug and play ISA devices can be assigned by the UEFI or the OS. And several PCI devices share one interrupt, which is assigned by UEFI or OS.
PAGE 44
Installing the Drivers 4. Installing the Drivers Regarding the driver program of this product, please refer to the enclosed CD.
PAGE 45
Appendix 5. Appendix 5.1 BPI Function EVOC BPI (BIOS Programming Interface) is a cross-platform, easy-to-maintain software interface specification, which supports access to hardware under the Protected Mode of the operating system.
PAGE 46
Appendix 4. Easy Maintenance Traditional WDT and GPIO programming are closely related to the hardware with complicated test and debug process and software of different platforms; however, the software developed by BPI only requires one set of the maintenance software. 5. Low Cost Developing the applications by BPI will not result in additional hardware and software cost, but it will reduce the development difficulty, development cycle and time-to-market for the system integrator.
PAGE 47
Appendix 5.2 Troubleshooting and Solutions Common Fault Issues to be Checked 8. Please make sure whether the power cord is well connected; 9. Please make sure whether the adopted power supply meets the power requirement of the motherboard; 10. Please check whether the CPU has been properly installed Unable to bootup after powered on and whether the CPU has been buckled properly; 11. Remove and install the memory module again; 12. Replace the memory module; 13.
PAGE 48
Appendix normally. 1. Please make sure the CPU fan is operating normally; 2. Please check whether the reset button has been triggered by accident; System reboots 3. Please check whether the system is affected by virus using anti-virus software; automatically 4. Please check whether the memory module or the peripheral card is loose; 5. Please make sure the load carrying capability of the adopted power supply is enough; you may try to replace the power. 1.
PAGE 49
Appendix system; please choose “Add Hardware” in the “Control Panel” in Windows system to set.